LIVING glow CP-CL02P RGB Motion Sensor Under Cabinet Light User Manual

June 9, 2024
LIVING glow

CP-CL02P RGB Motion Sensor Under Cabinet Light
User ManualLIVING glow CP-CL02P RGB Motion Sensor Under Cabinet
Light RGB Motion Sensor Under Cabinet Light
User Manual
Model: CP-CL02P

CP-CL02P RGB Motion Sensor Under Cabinet Light

Remove the protective film from the under cabinet light before use
Includes: 4 Under Cabinet Light Bars, 2 Remote Controls, 1 UL Approved 5V 2A Power Adapter, 1 3ft USB 4 in 1 Power Cord, 4 Mounting Brackets & 4 Sticker Mounting Pads.
How to use the RGB motion sensor under cabinet light
The Light has 3 working modes. ( ON- OFF – AUTO)

  1. Remove plastic protective film from the top of the light.
  2. Slide the switch on the light to ON, the light will come on and stay always on. Short press the top round button to change colors from White – Red – Green-Blue. Long press (more than 3 seconds) the top round button to J UMP mode
  3. Slide switch to OFF to turn the light off.
  4. Slide switch from ON to AUTO, the light will flash 2 times to motion sensor mode. The under cabinet light will turn on automatically when motion is detected in dark area, it will turn off automatically after approximately 90 seconds when no motion is detected. The light color only can be white in auto mode. Short press the round button on the under cabinet light to select brightness 30%-60%-100%.The under cabinet light has memory function in motion sensor mode, it will remember and stay in the same brightness as the last choice,but if we switch off or turn off the under cabinet light by controller and then turn on the under cabinet light, it will go back to 60% brightness white color.
  5. Slide the switch to “OFF” to save battery power if you do not use the light for a long time.

How to use the remote control

LIVING glow CP-CL02P RGB Motion Sensor Under Cabinet Light - remote control
1

| Turn light on and off.
---|---
| Motion sensor mode.
| Use color buttons to directly select single color mode.
| Dynamic color changing modes.
| 30% brightness energy saving mode.
| Decrease or Increase brightness of single color mode, decrease or increase speed of FADE / JUMP mode. Default brightness turns on at 60 % brightness.
| 2 hours/4 hours/6 hours turn off timer .

How to charge the RGB motion sensor under cabinet light
Please use original power adapter and USB cord to charge the RGB motion plastic under cabinet light, the indicator turns red when the RGB motion plastic under cabinet light is charging, it turns green when the under cabinet light is fully charged.
How to install the RGB motion sensor under cabinet light

  1. Sticks directly to an ironwork type surface.LIVING glow CP-CL02P RGB Motion Sensor Under Cabinet Light - remote control 8
  2. Use provided metal bracket , to stick the under cabinet light anywhere that doesn’t have an ironwork type surface.

Specification

Product Dimension 11.9 x 1.57 x 0.73 in
Input Voltage 120V 60Hz
Battery 3.7V 1000mAh
Charge Time 2-3 hrs when charge 1-2 units together, 3-4 hrs when charge 3-4

units together
Control Distance| approx. 16 – 26 ft
Runtime| Daylight 100% brightness – approx. 4 hrs,approx. RGB – 5-6 hrs
Max Lumen Output| 160 lm±10%
Standby Time| Approx. 90 seconds
Sensor Range| approx. 9.8- 13 Feet

Warning: Keep away from heat, do not store the under cabinet light in areas over 122 degrees F. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Responsible Party: KMS LLC. 811 E Waterman, Wichita Ks 67202, 1-800-752-5262
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Warranty: (6 Month limited)
In order to utilize the warranty,you must provide proof of purchase receipt that falls within the warranty time frame. If you would like to register your product you can go to WWW.LIVINGGLOW.COM or complete and mail the attached registration card to:
KMS LLC. ATTN: CUSTOMER SERVIC E 811 E WATERMAN WICHITA, KS 67202
For questions or part(s) on your Living Glow Under Cabinet Lights please visit our website at WWW.LIVINGGLOW.COM or email CUSTOMERSERVICE@1KMS.COM If you have no online access please call 800-752-5262 x 251
For Parts, please provide the model number, copy of receipt from purchase, name/part number and a brief description of the part needed,your name and the mailing address where you would like the replacement part to be sent. If you are unable to register your warranty online at WWW.LIVINGGLOW.COM Please fill out and mail the attached registration card to the address listed above. Keep your information in a safe place for reference.

WARRANTY REGISTRATION CARD

Name:…………………….
Phone #:——————–
Email:…………………….
Address:…………………………..
City:…………………………………..
St:…………………………………….
Zip:————————–
Product Description:…………………..
Date of Purchase:……………………………
Store Purchased From:……………………
Brand:…………………………………………
Model #:…………………………………
Serial #:…………………………………….

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals