SVGA 100W, 850W, 750W, 650W G7 Power Supply User Guide
- June 9, 2024
- SVGA
Table of Contents
SVGA 100W, 850W, 750W, 650W G7 Power Supply
Introduction: Premium Power
Introducing the EVGA SuperNOVA G7 – the most efficient, micro-sized 80 Plus® Gold-certified ATX power supply available. At only 130mm length, these power supplies find enough space to pack a half-bridge, LLC Resonant Controller and DC-DC design, along with 100% Japanese Capacitors and better layout placement to allow the SuperNOVA G7 to reach near-Platinum efficiency. Despite its size, these units remain whisper quiet with a 120mm FDB fan and EVGA ECO Mode to keep the power supply silent at medium to low loads, which can be monitored in real-time with the System Load Indicator Bars on the side of the power supply. Backed with EVGA’s 10-Year Limited Warranty and a full suite of protections, the EVGA SuperNOVA G7 is ready for play.
Safety Information
WARNING 1 : This unit has no user-serviceable parts inside. Opening the casing presents a risk of electrocution and will void the product’s warranty. EVGA will not be responsible for any result of improper use, including but not limited to, any use of the product outside of its intended purpose or use inconsistent with the warranty terms available online. (Warranty information is available at www.evga.com/support/warranty and this manual is available at www.evga.com/manuals).
WARNING 2 : Only use included cables or cables purchased from EVGA.com
that are specifically labeled for your PSU.
Using incorrect cables runs the risk of catastrophic failure.
What’s in the Box
Included with your EVGA SuperNOVA 650 / 750 / 850 / 1000 G7 power supply are the following items for proper installation and optional testing :
650 G7
- (1) EVGA Power Supply
- (1) EVGA Manual
- (4) Mounting Screws
- (1) EVGA PSU Tester (24-Pin)
- (1) 24-Pin ATX Cable
- (1) 8(4+4)-Pin EPS/ATX12V CPU Cable
- (1) 8(6+2)-Pin PCI-E VGA Cable
- (1) 2 x 8(6+2)-Pin PCI-E VGA Cable
- (2) 3 SATA Cables
- (1) 4 Molex Cable
- (1) Molex to FDD Adapter
- (1) Power Cord Cable (optional)
750 / 850 G7
- (1) EVGA Power Supply
- (1) EVGA Manual
- (4) Mounting Screws
- (1) EVGA PSU Tester (24-Pin)
- (1) 24-Pin ATX Cable
- (2) 8(4+4)-Pin EPS/ATX12V CPU Cables
- (2) 8(6+2)-Pin PCI-E VGA Cables
- (2) 2 x 8(6+2)-Pin PCI-E VGA Cables
- (3) 3 SATA Cables
- (1) 4 Molex Cable
- (1) Molex to FDD Adapter
- (1) Power Cord Cable (optional)
1000 G7
- (1) EVGA Power Supply
- (1) EVGA Manual
- (4) Mounting Screws
- (1) EVGA PSU Tester (24-Pin)
- (1) 24-Pin ATX Cable
- (2) 8(4+4)-Pin EPS/ATX12V CPU Cables
- (2) 8(6+2)-Pin PCI-E VGA Cables
- (3) 2 x 8(6+2)-Pin PCI-E VGA Cables
- (4) 3 SATA Cables
- (1) 4 Molex Cable
- (1) Molex to FDD Adapter
- (1) Power Cord Cable (optional)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Features
STABLE POWER
The G7 series has outstanding electrical performance with ultra stable voltage
and extremely clean power output. This can help you achieve the highest
possible overclock (optional) and provide the most stable and reliable power
to all components. The G7 series also has high efficiency up to 90% (115V~) /
92% (230V~) efficiency and is 80 PLUS® GOLD certified.
ECO THERMAL CONTROL SYSTEM
The EVGA ECO Intelligent Thermal Control System provides silent operation at
low loads, improved efficiencyand longer life span of the fan. Enabled by a
simple switch directly on the power supply, the “No Fan Spin” feature is ideal
for users looking to reduce ambient noise overall. Save on energy costs and
unnecessary fan usage with the EVGA ECO Thermal Control System.
TOP QUALITY PROTECTIONS
The G7 series comes equipped with the most comprehensive protection set
possible, including Over Voltage Protection (OVP), Under Voltage Protection
(UVP), Over Power Protection (OPP), Short Circuit Protection (SCP), Over
Current Protection (OCP), and Over Temperature Protection (OTP). This product
is also covered by an exceptional 10-year warranty and EVGA’s legendary
customer service and support.
SUPERIOR BUILD QUALITY
The G7 series is built to the highest standards, using 100% Japanese
capacitors rated at 105 degrees Celsius and high quality brand-name
semiconductor components for the highest performance and reliability. The
Ultra Quiet 120 mm Fluid Dynamic Bearing fan provides adequate cooling to
allow near silent operation.
MODULAR DESIGN
Reduce clutter in the case, improve ambient temperatures with better airflow
overall and provide a clean look to any system. Modular PSU designs allow the
user to disconnect the cables from the power supply side if they are not
needed for the specific configuration. This can help free up space inside the
case and improve cable management as well as airflow throughout the system.
SYSTEM LOAD INDICATOR BARS
The G7 series features real-time system load indicator bars on the side of the
power supply to display the current system load of the power supply in 20%
increments. The first indicator light notifies you that your system load is
between 0-20% of its rated wattage. The second bar will light up to notify you
that you are using between 20-40% of the rated system wattage, and each
successive bar will light up once it attains the next 20% of its rated
wattage. If the fifth bar lights up, this means that you are using between
80-100% of the rated wattage and you should consider upgrading to a higher
wattage power supply.
Installation
-
Remove the power supply from its packaging.
-
(Optional) Using the provided PSU testing tool, connect the 24-Pin cable to the PSU, then attach the testing tool to the 24-Pin cable. Connect the ATX power cable to the PSU and plug the PWR cable into the outlet or surge protector/UPS you plan to use. Once connected, turn the power switch to the ON position. (If the ECO mode is set to ON, the fan will not spin)
Please note : If you are using a water cooling configuration, this testing tool provides a simple, safe, option for bleeding/ draining/ testing water cooling components without the need of a paperclip or other device. -
Use the screws provided with your case to install the power supply into your computer.
NOTE : It is recommended to install the power supply with the fan facing down. However, if your case places the power supply at the bottom of the case and there are no ventilation holes available, it may be best to install the power supply with the fan facing up for greater efficiency and reliability .
-
Connect the 24-Pin ATX cable to the PSU and the motherboard.
-
Connect the 4+4-Pin EPS12V cable to the motherboard. (Optional) – If you plan on extreme overclocking and your motherboard supports additional
8- Pin or 4-Pin CPU power connectors,connect the second 4+4-Pin EPS12V cable. This is only needed for heavy overclocking or for Dual CPU motherboards .
-
Connect the 6/6+2-Pin PCI-E cables to your graphics card(s).
NOTE 1 : Do not attempt to plug an 8-Pin PCI-E cable into a 6-Pin connector without first detaching the two extra pins.
NOTE 2 : We recommend to use a single PCI-E cable to connect per port on graphic cards if your video card requires high power such as equipped with more than 2 PCI-E connectors 6pin + 8pin and 8pin + 8pin. -
Connect SATA power cables to all data drives or optical drives (hard drives, solid state drives, optical drives).
-
Connect the peripheral “Molex” 4-Pin connectors for fans, pumps, legacy components and other devices/adapters.
-
Connect the AC power cord to your power supply and to the wall. Check all connections to assure a solid connection and turn the power switch on the power supply to the ON position.
Q&A
Q : I see there are more than four screw holes on the back of the power
supply, but the packaging only offers (4) screws, are some missing?
A : Nothing is missing; you will only need to attach the EVGA power supply to
the case with four screws. The power supply offers more than (4) holes to
provide optimal compatibility for today’s varied case designs.
Q : My EVGA Power Supply includes (2) EPS cables for my motherboard, do I
need to connect up both?
A : Motherboards only require (1) 4+4 or 8-Pin EPS connection. On some models,
an additional 4+4-Pin or 8-Pin connection on the motherboard may be found for
dual CPU configurations or for extreme overclocking. If your motherboard
supports dual 4+4-Pin EPS connections, please refer to your motherboard
manufacturer’s manual for details on the proper function and power of the EPS
connections.
Q : What is the ECO Thermal Control System?
A : The ECO Thermal Control System, when enabled, allows the fan on your EVGA
power supply to shut off during low to moderate operation loads. The EVGA
power supply’s fan will automatically turn back on when needed, based on the
loading the power supply reaches. The fan will also increase in RPM when
needed, based on the load operation being requested from the components
connected. This prevents unnecessary rotation, reduces ambient noise levels
and will increase the life span of the fan due to the fan not spinning when
not required. Please Note : If the ECO Thermal Control is disabled the fan
will always spin, even at low loads. The fan will also increase in RPM as
needed automatically, based on the power draw from connected components.
Q : What if I want to use power adapters for my graphics
card(s)/motherboard/peripherals?
A : EVGA always recommends the use of direct power connections from the power
supply to power all components.
Q : Does it matter which end of the cable I plug into the power supply?
A : Yes, the connections going to the power supply will not have “break downs”
like the EPS (CPU) has 4+4 on one side and full 8-Pin on the other. Check each
cable as it is labeled appropriately to match the power supply side, and
connect only the same ‘‘matching” cable directly to the power supply as
referenced on each connector.
Q : If I have an issue or a question, can I get support?
A : ALL EVGA products are backed by top tier warranties as well as technical
support. Support can be reached for your power supply at :
- USA : +1-888-881-3842 option 1, option 3. or contact us via email at [email protected] .
- Europe : +49 89 189 049 11 or by email via eu.evga.com/support .
SuperNOVA 650 / 750 / 850 / 1000 G7 Cable Configuration
| 650 G7 | Modular Connector | Connector Per Cable | Cable Qty |
|---|---|---|---|
| MB | ATX 24-Pin x 1 | 1 | |
| CPU | EPS/ATX12V 8(4+4)-Pin x 1 | 1 | |
| VGA1,VGA2 | PCI-E 8(6+2)-Pin x 1 | 1 | |
| PCI-E 8(6+2)-Pin x 2 | 1 | ||
| SATA1, SATA2 | SATA 5-Pin x 3 | 2 | |
| PERIF | Molex 4-Pin x 4 | 1 | |
| FDD | Molex to FDD Adapter | 1 |
750 G7
850 G7| Modular Connector| Connector Per Cable| Cable Qty
---|---|---|---
MB| ATX 24-Pin x 1| 1
CPU| EPS/ATX12V 8(4+4)-Pin x 1| 2
VGA1, VGA2, VGA3 , VGA4| PCI-E 8(6+2)-Pin x 1| 2
PCI-E 8(6+2)-Pin x 2| 2
SATA1, SATA2, SATA3| SATA 5-Pin x 3| 3
PERIF| Molex 4-Pin x 4| 1
FDD| Molex to FDD Adapter| 1
| 1000 G7 | Modular Connector | Connector Per Cable | Cable Qty |
|---|---|---|---|
| MB | ATX 24-Pin x 1 | 1 | |
| CPU | EPS/ATX12V 8(4+4)-Pin x 1 | 2 | |
| VGA1,VGA2,VGA3,VGA4, VGA5 | PCI-E 8(6+2)-Pin x 1 | 2 | |
| PCI-E 8(6+2)-Pin x 2 | 3 |
SATA1, SATA2 ,SATA3,
SATA4| SATA 5-Pin x 3| 4
PERIF| Molex 4-Pin x 4| 1
FDD| Molex to FDD Adapter| 1
Dimensions: 86mm (H) x 150mm (W) x 130mm (L)
SuperNOVA 650 / 750 / 850 / 1000 G7 Specifications
| SuperNOVA 650 G7|
---|---|---
AC Input| 100-240V~, 9-4.5A, 60/50Hz
DC Output __| +3.3V| +5V| +12V| -12V| +5Vsb
MAX output, A| 24A| 24A| 54.1A| 0.5A| 3A
Combined, W| 120W| 650W| 6W| 15W
Output power, Pcont| 650W @ +50°C
| SuperNOVA 750 G7|
---|---|---
AC Input| 100-240V~, 10-5A, 60/50Hz
DC Output __| +3.3V| +5V| +12V| -12V| +5Vsb
MAX output, A| 24A| 24A| 62.5A| 0.5A| 3A
Combined, W| 120W| 750W| 6W| 15W
Output power, Pcont| 750W @ +50°C
| SuperNOVA 850 G7|
---|---|---
AC Input| 100-240V~, 12-6A, 60/50Hz
DC Output __| +3.3V| +5V| +12V| -12V| +5Vsb
MAX output, A| 24A| 24A| 70.8A| 0.5A| 3A
Combined, W| 120W| 850W| 6W| 15W
Output power, Pcont| 850W @ +50°C
| SuperNOVA 1000 G7|
---|---|---
AC Input| 100-240V~, 13-6.5A, 60/50Hz
DC Output __| +3.3V| +5V| +12V| -12V| +5Vsb
MAX output, A| 24A| 24A| 83.3A| 0.5A| 3A
Combined, W| 120W| 1000W| 6W| 15W
Output power, Pcont| 1000W @ +50°C
Protection: Over Voltage Protection (OVP), Under Voltage Protection (UVP), Short Circuit Protection (SCP), Over Power Protection (OPP), Over Current Protection (OCP), Over Temperature Protection (OTP).
References
- EVGA - BR - Suporte - Manuais de Produtos
- EVGA - BR - Warranty - Graphics Cards
- EVGA - DE - Garantie - Grafikkarten
- EVGA - EU - Support - Home
- EVGA - Intelligent Innovation - Official Website
- EVGA - Support - Product Manuals
- EVGA - Warranty - Graphics Cards