TAURUS LIGHT LZB1260 High-Power LED Zoom Bar 1260 User Manual
- June 4, 2024
- TAURUS LIGHT
Table of Contents
Tilt Bar Zoom 1260
12pcs 60W RGBW 4in1 LED
User ManualKEEP THIS MANUAL FOR FUTURE NEEDS
Unpacking
Thank you for choosing our product. For your own safety, please read this
manual before installing the device. This manual covers important information
on installation and applications. Please install and operate the fixture with
the following instructions. Meanwhile, please keep this manual well for future
needs.
This fixture is made of a new type of high-temperature strength engineering
plastics and cast aluminum casing with a nice outlook. The fixture is designed
and manufactured strictly following CE standards, complying with international
standard DMX512 protocol. It’s available independently controlled and linkable
with each other for operation. And it is applicable for large-scale live
performances, theaters, studios, nightclubs, and discos.
4-IN-1 LEDs(RGBW) feature high brightness and stability. Please carefully
unpack it when you receive the fixture and check whether it is damaged during
the transportation. And please check whether the following items are included
inside the box:
LED Pixel Zoom bar—-One
3-Pin Signal Cable—-One
Omega Bracket—-Two
Power Cable—-One
Safety Cable—-one
User Manual—-One
Fixture size
Unit of length: mm
Safety Instructions
CAUTION! Be careful with your operations. With a dangerous voltage, you
can suffer a dangerous electric shock when touching wires!
This device has left the factory in perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for
the user to follow the safety instructions and warning notes written in this
user manual.
Important:
Damages caused by the disregard of this user manual are not subject to a
warranty. The dealer will not accept liability for any resulting defects or
problems.
If the device has been exposed to temperature changes due to environmental
changes, do not switch it on immediately. The arising condensation could
damage the device. Leave the device switched off until it has reached room
temperature.
This device falls under protection-class I. Therefore it is essential that the
device be earthed.
The electric connection must carry out by a qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of
this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this
would be the case, replacement of the cable must be done by an authorized
dealer.
Always disconnect from the mains, when the device is not in use or before
cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the
power cord.
During the initial start-up, some smoke or smell may arise. This is a normal
process and does not necessarily mean that the device is defective, it should
decrease gradually.
Please don’t project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm
distance from the wall for smooth airflow, so there should be no shelter for
fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall
be exclusively replaced by the manufacturer or his service agent or a
similarly qualified person in order
to avoid a hazard.
Don’t use the fixture in RGBW full-on for more than 10 minutes in case of
high-temperature damage to the fixtures.
Operation Instructions
-
The fixture is for beam effect purposes.
-
Don’t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environmental changes. So
make sure to operate the fixture until it is at normal temperature. -
This light should be kept away from strong shaking during any transportation or movement.
-
Don’t pull up the light by only the head, or it might cause damage to the mechanical parts.
-
Don’t expose the fixture to overheating, moisture, or environment with too much dust when installing it. And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
-
Make sure the installation place is in good safe condition before installing the fixture.
-
Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture.
-
Make sure the lens are in good condition. It’s recommended to replace the units if there are any damages or severe scratches.
-
Make sure the fixture is operated by qualified personnel who know the fixture before use.
-
Keep the original packages if any second shipment is needed.
-
Don’t try to change the fixtures without any instruction from the manufacturer or the appointed repair agencies.
-
It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
Mounting and Installation
Cautions: For added protection mount the fixtures in areas outside
walking paths, seating areas, or in areas where the fixture might be reached
by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation
area can hold a minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety
attachment, such as an appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing
the fixture from a periodic safety inspection of all installation material and
the fixture. If you lack these qualifications, do not attempt the installation
yourself. Improper installation can result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting
the main power cord to the appropriate wall outlet.
Clamp Mounting: The LED Pixel Zoom bar provides a unique mounting bracket
assembly that integrates the bottom of the base, and the safety cable rigging
point in one unit (see the illustration below). When mounting this fixture to
the truss be sure to secure an appropriately rated clamp to the included omega
bracket using an M10 screw fitted through the center hole of the “omega
bracket”. As an added safety measure be sure to attach at least one properly
rated safety cable to the fixture using one of the safety cable rigging points
integrated into the base assembly
Regardless of the rigging option you choose for your LED pixel Zoom par, always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle.
DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your
controller and the other side to the male 3-pin XLR input of the moving head.
(5-pin connect way is similar)
You can chain multiple Moving heads to be connected together through serial
linking. The cable needed should be a two-core, screened cable with XLR input
and output connectors. Please refer to the diagram below.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3, which is then plugged into the output XLR socket of the last fixture in the chain. Please see the illustrations below.
DMX Channel
1. 56 Channels
Channel | Value | Function |
---|---|---|
1 | 0-255 | Y Movement |
2 | 0-255 | Y movement fine |
3 | 000-007 |
008-247
248-255| Y Speed
Normal
From slow to fast
Normal
4| 000-255| Zoom
5| 0-255| Dimmer
6| 0-255| Dimmer fine
7| 000-031
032-063
064-095
096-127
128-159
160-191
192-223
224-255| Strobe
Close
Open
From fast to slow
Open
Pulse: From fast to slow
Open
Random: From fast to slow
Open
8| 000-100
101-160
161-255| Function
None
Motor reset
None
9| 000-255| LED1R
10| 000-255| LED1G
11| 000-255| LED1B
12| 000-255| LED1W
13| 000-255| LED2R
14| 000-255| LED2G
15| 000-255| LED2B
16| 000-255| LED2W
.| .| .
.| .| .
.| .| .
.| .| .
53| 000-255| LED12R
54| 000-255| LED12G
55| 000-255| LED12B
56| 000-255| LED12W
2. 40 Channels
Channel | Value | Function |
---|---|---|
1 | 0-255 | Y Movement |
2 | 0-255 | Y movement fine |
3 | 0-255 | Zoom |
4 | 000-255 | 101-160 reset(hold 3 second) |
5 | 0-255 | LED 1 Dimmer |
6 | LED 1 Strobe | |
0-9 | nose |
10-130
131-255| The pulse from slow to fast
Random from slow to fast
7| 0-8| RGBW
9-18| R
19-28| G
29-38| B
39-48| RG
49-58| RB
59-68| GB
69-78| RW
79-88| RGB
89-98| W
99-255| Color Auto
8| 0-255| LED2 Dimmer
9| | LED 2 Strobe
0-9| Close
10-130| The pulse from slow to fast
131-255| Random from slow to fast
10| 0-8| RGBW
9-18| R
19-28| G
29-38| B
39-48| RG
49-58| RB
59-68| GB
69-78| RW
79-88| RGB
89-98| W
99-255| Color Auto
.
–
•| .
.
•| .
.
•
38| 0-255| LED12 Dimmer
39| | Strobe
0-9| Close
| 10-130| The pulse from slow to fast
---|---|---
131-255| Random from slow to fast
40| 0-8| RGBW
9-18| R
19-28| G
29-38| B
39-48| RG
49-58| RB
59-68| GB
69-78| RW
79-88| RGB
89-98| W
99-255| Color Auto
3. 16 Channels
Channel
| Value|
Function
---|---|---
1| 000-255| Y movement
2| 000-255| Y movement fine
3| 000-255| Zoom
4| 000-255| Dimmer
5| 000-255| Dimmer Fine
6| 000-031
032-063
064-095
096-127
128-159
160-191
192-223
224-255| Strobe
Close
Open
From fast to slow
Open
The pulse from fast to slow
Open
Random from fast to slow
Open
7| 000-008
009-038
039-068
069-098
099-128
129-158
159-187
188-255| None
Effect 1
Effect 2
Effect 3
Effect 4
Effect S
Effect 6
Effect 7
8| 000-255| Effect with font color
9| 000-255| Effect with back color
10| 000-255| Built-in program: 0-9 none, each 10 Dmx value one effect
11| 000-255| Built-in Speed
12| 000-255| R
13| 000-255| G
14| 000-25| B
15| 000-25| W
16| 000-10
0
101-16
0| Function
None
Motor reset
None
Features and Specifications:
- Input voltage: AC90-AC240 50-60HZ
- LED Source: 12x60W RGBW 4in1 LED
- RGBW color mixing, pixel control
- Color Temp: 8000K
- Light source life: 50,000 hours on average
- Dimming: 0-100% linear dimming
- Maximum power: 680W
- Tilt Movement: 220°+16 bit Smooth
- Strobe: 1-25 times/second
- Zoom angle: 3°-40°
- DMX Channels: 16/40/56CH
- IP Rated: IP20
- Size: 1080x130x315mm