FABTECH 4 Inch Uniball UCA 2021 to 22 Ford Bronco 2 Door 4WD Instructions
- June 4, 2024
- FABTECH
Table of Contents
4 Inch Uniball UCA 2021 to 22 Ford Bronco 2 Door 4WD
Instruction Manual
| FTS22356| FORD BRONCO 2.25” DLSS RESI (REAR 2-DOOR)
---|---|---
1| FT82077D| 2.5” DLSS C/O W/RESI (DRIVER)
1| FT82077P| 2.5” DLSS C/0 W/RESI (PASSENGER)
2| FT30977| RESI MOUNT
1| FT82075i| INSTRUCTIONS
1| FT86126| HARDWARE SUBASSEMBLY
| FT86126| HARDWARE SUBASSEMBLY
---|---|---
4| FT30964| MISALIGNMENT SPACER
1| FT86125| HARDWARE KIT
Thank you for purchasing Dirt Logic shocks, the finest off-road shock in the industry. Each unit is built to exacting standards and is properly tuned specifically for your vehicle. Dirt Logic shocks are designed and built to both beautify and upgrade your suspension system.
How To Care For Your Dirt Logic Shocks
Dirt Logic shocks have been designed as a take-apart, serviceable, race-style
unit. That means, just like a race shock, it will need to be maintained and
periodically rebuilt. The tight tolerances of this provide the exceptional
ride and performance you are paying for but do require maintenance which is
normal in a take-apart shock like a Dirt Logic.
Externally, the shock should be kept clean at all times and kept free of dirt,
road salt or other corrosive elements. The unit should be routinely washed
with a pH-balanced cleaner to keep the finish looking new. Do not use any
abrasive or aggressive cleaners or degreasers as it will harm the finish for
life including the aluminum anodizing.
Internally, the shock has high-performance seals that allow the shock to cycle
at very high rates and provide exceptional damping in aggressive off-road
conditions. These seals are wearable items and may need to be replaced
periodically to keep the shock functioning correctly. Our in-house Shock Lab
is equipped to handle these needs when necessary.
Caution – Read Before Installing
Stop – Call FABTECH customer service if any component of this product is
missing. Do not return it to the place of purchase!
For technical assistance call:
909-597-7800
This Dirt Logic Shock is shipped pressurized with Nitrogen. Do not remove the
tamper cap or the warranty will be void.
If this shock is equipped with a reservoir hose, do not loosen or remove the
hose or the warranty will be void.
If this shock is equipped with a coil, be aware that the coil has some amount
of preload from the factory and should not be removed. Removal of the coil
will void the warranty.
If this shock product needs to be returned for any reason, it must be returned
in its original packaging or the warranty will be void.
Dirt Logic Shocks come with a one-year warranty from the original date of
purchase for defects in material or workmanship.
A spanner wrench can be purchased for future adjustment. (FTS89905 for 4.0,
FTS98008 for 2.5, FTS98006 for 2.0)
If adjustment is needed. Jack up the vehicle to relieve tension on the Dirt
Logic coil over before making adjustments or the top cap may come loose.
Should you have any questions regarding your Dirt Logic Shocks, please feel
free to contact us.
INSTRUCTIONS
-
Install the new driver-side Coilover using the supplied 3/8” hardware for the upper mount. NOTE: Install the innermost bolts first then install the outer two along with FT30977 (Resi Mount) Torque to 45 ft-lbs. SEE FIGURES 1-3.
-
Install the lower Coilover to the axle mount using factory hardware as well as two FT30964 (Misalignments). Torque to 160 ft-lbs. SEE FIGURE 4
-
Mount the rest to the mount using the supplied clamps.
SEE FIGURE 5
-
Repeat the steps on the passenger side.
-
Continue with the rest of the installation instructions for the other component parts.
For technical assistance call: 909-597-7800
Product Warranty and Warnings
Fabtech provides a Limited Lifetime Warranty to the original retail purchaser
who owns the vehicle, on which the product was originally installed, for
defects in workmanship and materials.
The Limited Lifetime Warranty excludes the following Fabtech items; bushings,
bump stops, ball joints, tie rod ends, limiting straps, cross shafts, Heim
joints, and driveshafts. These parts are subject to wear and are not
considered defective when worn.
They are warranted for 60 days from the date of purchase for defects in
workmanship.
Dirt Logic and Performance Coilover take-apart shocks are considered
serviceable shocks with a one year warranty on leakage only. Service seal kits
are available separately for future maintenance. All other shocks are covered
under our Limited Lifetime Warranty.
Fabtech does not warrant any product for finish, alterations, modifications,
and/or installation contrary to Fabtech’s instructions.
Alterations to the finish of the parts including but not limited to painting,
powder coating, plating, and/or welding will void all warranties. Some finish
damage may occur to parts during shipping, which is considered normal and is
not covered under warranty.
Fabtech products are not designed nor intended to be installed on vehicles
used in race applications or for racing purposes or similar activities. (A
“RACE” is defined as any contest between two or more vehicles, or any contest
of one or more vehicles against the clock, whether or not such contest is for
a prize). This warranty does not include coverage for police or taxi vehicles,
race vehicles, or vehicles used for government or commercial purposes. Also
excluded from this warranty are sales outside of the United States of
America.
Installation of most suspension products will raise the center of gravity of
the vehicle and will cause the vehicle to handle differently than stock. It
may increase the vehicle’s susceptibility to a rollover, on-road, and off-
road, at all speeds. Extreme care should be taken to operate the vehicle
safely at all times to prevent rollover or loss of control resulting in
serious injury or death.
Fabtech front-end Desert Guards may impair the deployment or operation of
vehicles equipped with supplemental restraining systems/air bag systems and
should not be installed if the vehicle is equipped as so.
Fabtech makes every effort to ensure the suspension product compatibility with
all vehicles listed on the website, but due to unknown auto manufacturer’s
production changes and/or inconstancies by the auto manufacturer, Fabtech
cannot be responsible for 100% compatibility, including the fitment of tire
and wheel sizes listed. The Tire and Wheel sizes listed in Fabtech’s website
are only a guideline for street driving with noted fender trimming. Fabtech is
not responsible for damages to the vehicle’s body or tires. Fabtech is not
responsible for premature wear of factory components due to the installation
of oversized tires and wheels.
Fabtech’s obligation under this warranty is limited to the repair or
replacement, at the Fabtech option, of the defective product only.
All costs of removal, installation or re-installation, freight charges, and
incidental or consequential damages are expressly excluded from this warranty.
Fabtech is not responsible for damages and/or warranty of other vehicle parts
related or nonrelated to the installed Fabtech product. This warranty is
expressly in lieu of all other warranties expressed or implied. This warranty
shall not apply to any product that has been subject to accident, negligence,
alteration, abuse or misuse as determined by Fabtech.
Fabtech suspension components must be installed as a complete system including
shocks as shown on our website. All warranties will become void if Fabtech
parts are combined and/or substituted with other aftermarket suspension
products.
Combination and/or substitution of other aftermarket suspension parts may
cause premature wear and/or product failure resulting in an accident causing
injury or death. Fabtech does not warrant products not manufactured by
Fabtech.
Depending on the condition of the factory suspension components retained after
the installation of a Fabtech suspension, not all vehicles may have the same
ride stance front to rear as described in the website. The blue color of
suspension components shown in all Fabtech photographs is for display purposes
only. The majority of all Fabtech components will be black specifically where
noted with part numbers ending in BK.
Installation of Fabtech products may void the vehicle’s factory warranty; it
is the consumer’s responsibility to check with their local vehicle’s dealer
for warranty disposition before the installation of the product. Some state
laws may prohibit the modification of suspension to a vehicle in whole or in
part. It is the responsibility of the installer and consumer to consult local
laws prior to the installation of any Fabtech suspension product to comply
with such written laws.
It is the responsibility of the distributor and/or the retailer to review all
warranties and warnings of Fabtech products with the consumer prior to
purchase.
Fabtech reserves the right to super cede, discontinue, change the design,
finish, part number, and/or application of parts when deemed necessary without
written notice. Fabtech is not responsible for misprints or typographical
errors within the website or price sheet.
For the most recent Product Warranty and Warnings visit our website
www.fabtechmotorsports.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>