GRACO Snugessentials i-Size Infant Child Restraint Owner’s Manual
- June 8, 2024
- Graco
Table of Contents
- Snugessentials i-Size Infant Child Restraint
- IMPORTANT **
- Product Information
- Concerns on Installation
- Handle Adjustment
- Installation with base
- Securing Child in the Enhanced Child Restraint
- Installation without base
- Detaching Seat Pad
- Care and Maintenance
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SNUGESSENTIALS™ i-SIZE INFANT CHILD RESTRAINT
ATTACHED TO ISOFAMILY BASE
IMPORTANT! KEEP FOR FUTURE REFERENCE.
I so Family Base sold separately**
must be used to meet i-Size standard
Owner’s Manual
Parts List
Fitting Guide
**
gracobaby.eu • gracobaby.pl
GIM-0055I
Snugessentials i-Size Infant Child Restraint
1 Handle
2 Hood
3 Head Support
4 Shoulder Harness
5 Harness Buckle
6 Shoulder Harness
7 Harness Adjustment Button
8 Adjustment Webbing| 9 Handle Button
10 Side Guide
11 Instructional Manual (under Seat Covers)
12 Infant Insert
13 Stroller Fix Release Button
14 Harness Slot
15 Rear Guide
16 Shoulder Harness
17 Crotch strap
---|---
1 Load Leg Indicator
2 Load Leg
3 Load Leg Adjustment Button
4 ISOFIX Connector| 5 ISOFIX Releasing Button
6 Shell Indicator
7 ISOFIX Guides
8 ISOFIX Adjustment Button
---|---
IMPORTANT **
**
READ THESE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THEM FOR FUTURE
REFERENCE. YOUR CHILD’S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW THESE
INSTRUCTIONS. WARNING: IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
Please check before you purchase this enhanced child restraint to make sure it
can be installed properly in your vehicle. NO enhanced child restraint can
guarantee full protection from injury in an accident. However, proper use of
this enhanced child restraint will reduce the risk of serious injury or death
to your child.
To use this enhanced child restraint with the ISOFIX connections according to
the ECE R129/02 Regulation, your child must meet the following requirements.
Child height 40cm-75cm/ Child weight ≤13kg (Child age< 12 months).
To use this infant carrier module with vehicle belt, your child must meet the
following requirements. Child weight ≤13kg/ Child age< 12 months.
Any straps of enhanced child restraint should be tightened and not twisted.
DO NOT install this enhanced child restraint without following the
instructions in this manual or you may put your child at serious risk of
injury or death.
NEVER leave your child unattended with this enhanced child restraint.
DO NOT make any modification to this enhanced child restraint or use it along
with component parts from other manufacturers.
DO NOT use this enhanced child restraint if it has damaged or missing parts.
DO NOT have your child in large/ oversized clothes because this may prevent
your child from being properly and securely fastened by the shoulder harness
straps and the crotch strap between the legs.
DO NOT leave this enhanced child restraint or other items unbelted or
unsecured in your vehicle because an unsecured enhanced child restraint can be
thrown around and may injure occupants in a sharp turn, sudden stop, or
collision.
DO NOT place a rear-facing enhanced child restraint on front seat with air
bag. Death or serious injury may occur. Please refer to vehicle owner’ s
manual for more information.
NEVER use a second-hand enhanced child restraint or an enhanced child
restraint whose history you do not know because it may have structural damage
that compromises your child’ s safety.
NEVER use ropes or any other substitutes to secure enhanced child restraint in
vehicle or to secure child into enhanced child restraint.
DO NOT use this enhanced child restraint without the soft goods.
The soft goods should not be replaced with any besides the ones recommended by
the manufacturer. The soft goods constitute an integral part of the enhanced
child restraint performance.
DO NOT put anything other than the recommended inner cushions in this enhanced
child restraint.
Be sure that the enhanced child restraint is installed in such a way that no
part of it interferes with movable seats or in the operation of vehicle doors.
DO NOT continue to use this enhanced child restraint after it has uered any
type of crash, even a minor one. Replace immediately as there may be
invisible, structural damage from the crash.
Remove this infant carrier module and base from the vehicle seat when it is
not in regular use.
Consult the distributor for issues concerning maintenance, repair and part
replacement.
To avoid the risk of falling out, always secure the child using the child
harness when the child is placed in infant carrier module, even when the
enhanced child restraint is not in the vehicle. Before carrying the infant
carrier module by hand, ensure that the child is fastened with the child
harness, and that the handle is correctly locked in a vertical position.
To avoid serious injury or death, NEVER place infant carrier module on
elevated surface seat with child in it. The parts of this enhanced child
restraint should not be lubricated in any way.
Always secure child in enhanced child restraint, even on short trips, as this
is when most accidents occur.
Please keep this enhanced child restraint away from sunlight, because it may
be too hot for child’s skin. Always touch the enhanced child restraint before
placing child in it.
Product Information
“i-Size” (Integral Universal ISOFIX Enhanced Child Restraint Systems) is a category of Enhanced Child Restraint System for use in all i-Size seating position of a vehicle.
- According to the ECE R129/02 Regulation, the product is a Universal ISOFIX Class ISO/ R2 enhanced child restraint and should be fitted using the ISOFIX connections.
- This is an “i-Size” Enhanced Child Restraint System. It is approved according to Regulation No.129, for use in, i-Size compatible vehicle seating positions as indicated by vehicle manufacturers in the vehicle users’ manual.
- If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.
It is approved to ECE R129/02 series of amendments, not all vehicle
manufacture’s handbooks list i-Size compatibility yet. This seat and base is
also approved for use in ISOFIX compatible vehicles. Please refer to the
vehicle manufacturer’s website or consult your dealer.
It will fit vehicles with positions approved as i-Size ISOFIX positions (as
detailed in the vehicle handbook), depending on the category of the enhanced
child restraint and of the fixture.
Concerns on Installation
See images 1 – 3
1 DO NOT install this enhanced child restraint on vehicle seats that face
sideways or rearward with respect to the moving direction of the vehicle.
It is recommended to install this enhanced child restraint on the rear vehicle
seat. DO NOT install this enhanced child restraint on vehicle seats movable
during installation.
2 DO NOT place rear-facing enhanced child restraint on front seat with air
bag, because death or serious injury may occur. Please reference vehicle
owner’ s
manual for more information.
3 This infant carrier is suitable for vehicle seats with i-Size ISOFIX anchor
points with the Base.
Handle Adjustment
See image 4
4 To adjust the handle, squeeze the handle buttons on both sides to release it
, and then rotate the handle until it clicks into any of the 4 positions.
The handle of the infant carrier module can be adjusted to 4 positions.
Position A – Position for car, hand or stroller transportation. Position B&C –
Rocking position.
Position D – Baby chair position.
Installation with base
See images 5 – 15
5 Fit the ISOFIX guides with the ISOFIX anchor points. The ISOFIX guides can
protect the surface of the vehicle seat from being torn. They can also guide
the ISOFIX connectors.
6 Unfold the load leg from storage compartment.
7 Line up the ISOFIX connectors with the ISOFIX guides, and then click both
ISOFIX connectors into the ISOFIX anchor points.
8 Make sure that both ISOFIX connectors are securely attached to their ISOFIX
anchor points. There should be two audible clicks and the colors of the
indicators on the both ISOFIX connectors should be completely green. Check to
make sure the base is securely installed by pulling on the both ISOFIX
connectors.
9 After placing the base on the vehicle seat, extend the load leg to floor.
When the load leg indicator shows green, it means it is installed correctly.
When the load leg indicator shows red, it means the load leg is in the wrong
position. Make sure the load leg is in full contact with the vehicle floor
pan.
Squeeze the load leg releasing button, then shorten the load leg upwards. The
completely assembled base is shown as 10 This infant carrier is suitable for
vehicle seats with i-Size ISOFIX anchor points with the Base.
The ISOFIX connectors must be attached and locked onto the ISOFIX anchor
points. The load leg must be installed correctly with green indicator.
11 Push the infant carrier down into the base, if the enhanced child restraint
is secure, the enhanced child restraint indicator shows green. 12 Pull up on
the infant carrier to be sure it is securely latched into the base.
13 Press the ISOFIX adjustment button and push the base back against the
vehicle seat until tight.
14 To release the infant carrier, pull the infant carrier up while pull out
the stroller fix release button.
15 To remove the base, press the secondary lock button first and then the
ISOFIX releasing button on the ISOFIX connectors before removing the base from
the vehicle seat.
Securing Child in the Enhanced Child Restraint
See images 16 – 25
16 While pressing the harness adjustment button, pull completely the two
shoulder harnesses of the enhanced child restraint.
17 Unlock the buckle of the harnesses by pressing the red button.
18 Do not remove the Head Support before the baby sitting. 19 20 Infant insert
is for children’s protection. Children under 60cm are suitable to use the
infant insert. 21
22 Check that shoulder harness straps are set at proper height.
23 Place child into the infant carrier module and lock the buckle. 24
25 Tighten the shoulder harnesses by pulling adjustment webbing.
Installation without base
See images 26 – 30
DO NOT install this infant carrier module on vehicle seats with Lap Belts.
26 This infant carrier module is suitable for vehicle seats with a 3-point
retractor safety belt only.
27 Place the infant carrier module onto the vehicle seat where you wish to put
it.
28 Pull the vehicle safety belt out and lock it into the vehicle buckle,
sliding the vehicle lap belt into the side guides of the infant carrier
module.
29 Slide diagonal belt into the rear guide. The infant carrier module can not
be used if the vehicle safety belt buckle (female buckle end) is too long to
anchor the infant carrier module securely.
30 Pull the vehicle shoulder belt to fasten the infant carrier module tightly
and securely.
Detaching Seat Pad
See images 31 – 32
To re-assemble the soft goods, reverse the aforementioned steps.
Care and Maintenance
See images 33 – 34
Wash the seat cover and inner padding with cold water (temperature below
30°C).
Do not iron the soft goods.
Do not bleach or dry clean the soft goods.
Do not use undiluted detergents, gasoline or other organic solvent to wash the
infant carrier module.
It may cause damage to the enhanced child restraint.
Do not twist the seat cover and inner padding in an attempt to dry.
It may leave the seat cover and inner padding with wrinkles.
Hang dry the seat cover and inner padding in the shade.
Remove the enhanced child restraint from the vehicle seat if it is not going
to be used for a long period of time. Put the enhanced child restraint in a
cool, dry place and somewhere your child cannot access it.
Store the instruction manual in the slot where the manual icon is shown. To
purchase replacement parts or accessories, please contact us at the following:
gracobaby.eu
www.gracobaby.pl
Product of:
Wonder Brands Limited
FLAT/RM 1501, 15/F, Capital Centre,
151 Gloucester Road,
Wan Chai, Hong Kong
Customer Service
gracobaby.eu
www.gracobaby.pl
For UK and ROI
Customerservices.uk@gracobaby.eu
+44 0800 952 0063
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>