Hogar Controls Hogar Pebble HC-TB-ZW Manual
- June 8, 2024
- Hogar Controls
Table of Contents
- Hogar Controls
- Hogar Pebble
- SKU: HC-TB-ZW
- Quickstart
- Important safety information
- What is Z-Wave?
- Product Description
- Prepare for Installation / Reset
- Inclusion/Exclusion
- Communication to a Sleeping device (Wakeup)
- Quick trouble shooting
- Association – one device controls an other device
- Technical Data
- Supported Command Classes
- Controlled Command Classes
- Explanation of Z-Wave specific terms
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Hogar Controls
Hogar Pebble
SKU: HC-TB-ZW
Quickstart
This is a
secure
Wall Controller
for
CEPT (Europe).
Please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
1. Put the controller into INCLUSION mode. Follow the instructionsprovided by
the controller manufacturer.2. Press and hold the config button for more than
2 seconds. ALL indicator lights will blink 3 times. At this point release the
config button, the device will start the inclusion process.
Please refer to the
Manufacturers
Manual for more information.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in
this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any
loss or damage resulting from failure to comply with the instructions in this
manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal
instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart
Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message ( two-
way
communication) and every mains powered node can act as a repeater for other
nodes
( meshed network ) in case the receiver is not in direct wireless range of
the
transmitter.
This device and every other certified Z-Wave device can be used together
with any other
certified Z-Wave device regardless of brand and origin as long as both are
suited for the
same frequency range.
If a device supports secure communication it will communicate with other
devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to
maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc.
please refer
to www.z-wave.info.
Product Description
The Pebble from Hogar Controls is a wireless touch button that combines elegant design and functionality into a simple, personalized device to control everything in your home. Enabled with a smart touch interface, this suave, compact device can do much more than your run-of-the-mill remote control ever could. Easily attach the Pebble on any glass, wooden or metal surface, or carry around in your pocket to control smart lighting, music, shades, thermostats and much more in your smart home or ofce.It is a compact, battery- powered, Z-wave Plus compatible device that allows you to control various devices through the Z-wave network. As it is based on Z-Wave communication technology, the device can be controlled remotely from anywhere using the internet.When paired with the HC Pro, our smart home controller, the Pebble lets you design, set and activate up to 9 personalized scenes with different gestures like touch, tap, double tap, press, press and hold, swipe left, swipe right, swipe up, swipe down, swipe clockwise, swipe anticlockwise.Set the ambiance for date night, wake up to your own personal mix of actions, or have the house locked and secured before you go to bed. Imagine your home at your ngertips because, with Pebble, it is just a matter of touch-and-go.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory
default
state. Please make sure to reset the device into factory default. You can do
this by
performing an Exclusion operation as described below in the manual. Every
Z-Wave
controller is able to perform this operation however it is recommended to use
the primary
controller of the previous network to make sure the very device is excluded
properly
from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave
controller. This
procedure should only be used when the primary controller is inoperable.
Please use this procedure only when the network primary controller is missing or otherwise inoperable.To reset the device, use stick press and hold Config button till all LEDs are ON (about 5 seconds). The device is successfully removed from the network and reset.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The
device needs
to be added to an existing wireless network to communicate with the
devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called
Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network.
This
controller is turned into exclusion respective inclusion mode. Inclusion and
Exclusion is
then performed doing a special manual action right on the device.
Inclusion
1. Put the controller into INCLUSION mode. Follow the instructionsprovided by the controller manufacturer.2. Press and hold the config button for more than 2 seconds. ALL indicator lights will blink 3 times. At this point release the config button, the device will start the inclusion process.
Exclusion
1. Put the controller into EXCLUSION mode. Follow the instructions provided by the controller manufacturer.2. Press and hold the config button for more than 2 seconds. ALL indicator lights will blink. At this point release the configbutton, the device will start the exclusion process.
Communication to a Sleeping device (Wakeup)
This device is battery operated and turned into deep sleep state most of the
time
to save battery life time. Communication with the device is limited. In order
to
communicate with the device, a static controller C is needed in the
network.
This controller will maintain a mailbox for the battery operated devices and
store
commands that can not be received during deep sleep state. Without such a
controller,
communication may become impossible and/or the battery life time is
significantly
decreased.
This device will wakeup regularly and announce the wakeup
state by sending out a so called Wakeup Notification. The controller can then
empty the mailbox. Therefore, the device needs to be configured with the
desired
wakeup interval and the node ID of the controller. If the device was included
by
a static controller this controller will usually perform all necessary
configurations. The wakeup interval is a tradeoff between maximal battery
life time and the desired responses of the device. To wakeup the device please
perform
the following action:
- Touch the center of the touch area, all indicator LEDs will blink ON then OFF, after all LEDs are OFF, the device will wake up.2) Then touch on the touch area 3 times, the device will send Wakeup Notification.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one
device
controlling another device is called association. In order to control a
different
device, the controlling device needs to maintain a list of devices that will
receive
controlling commands. These lists are called association groups and they are
always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’
Command.
Association Groups:
Group NumberMaximum NodesDescription
1| 3| Name: LifelineCommands:- Device Reset Locally Notification – Battery
Report – Central Scene Notification
---|---|---
2| 3| Name: Basic On-OffCommands:- Basic SetWhen Single touch: device send
Basic Set ON to 2nd association group.When Double touch: device send Basic Set
OFF to 2nd association group.
Technical Data
Hardware Platform | ZM5202 |
---|---|
Device Type | Wall Controller |
Network Operation | Reporting Sleeping Slave |
Firmware Version | HW: 1 FW: 1.03 |
Z-Wave Version | 6.71.03 |
Certification ID | ZC10-18106271 |
Z-Wave Product Id | 0x0293.0x0003.0x0113 |
Firmware Updatable | |
Z-Wave Scene Type | |
Security V2 | S2_UNAUTHENTICATED |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Battery
- Central Scene V3
- Device Reset Locally
- Manufacturer Specific V2
- Multi Channel Association V3
- Powerlevel
- Security 2
- Supervision
- Transport Service V2
- Version V3
- Wake Up V2
- Zwaveplus Info V2
Controlled Command Classes
- Basic
Explanation of Z-Wave specific terms
-
Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers. -
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls. -
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network. -
Inclusion — is the process of adding new Z-Wave devices into a network.
-
Exclusion — is the process of removing Z-Wave devices from the network.
-
Association — is a control relationship between a controlling device and
a controlled device. -
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate. -
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>