MATRIX Labs

MATRIX Creator

SKU: MATRIX.C1.US

Quickstart

This is a ****

Hardware Device
for
U.S. / Canada / Mexico.

To run this device please connect it to your mains power supply.

To add this device to your network execute the following action:
MATRIX Creator is a Z-Wave Plus Hardware Platform Product. It provides communication with the Z-Wave SerialAPI running on the Z-Wave module in the MATRIX Creator. Refer to Sigma design Z-Wave Specification (http://zwavepublic.com/specifications) and developer resources (http://zwavepublic.com/developer).

Please refer to the
Manufacturers Manual for more information.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

MATRIX Creator is a Raspberry Pi development board with an IoT-ready platform that lets users build computer vision, home automation, robotics, and other custom hardware solutions. From a hardware perspective, MATRIX Creator is an all inclusive solution, consolidating an ultraviolet sensor, pressure sensor, 3D accelerometer, 3D gyroscope, 3D magnetometer, humidity sensor, 8 MEMs microphone array, a temperature sensor, 35 RGBW LEDs array, as well as a Xilinx Spartan 6 FPGA and an Atmel ARM Cortex M3 microcontroller. Connectivity and communication standards are equally abundant, consisting of Zigbee, Z-Wave, NFC, IR RX/TX, 2 ADC Channels, 17 digital GPIOs, SPI, I2C, UART.https://creator.matrix.one/

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

Factory reset should be done by software. Please refer to the documentation (https://matrix-io.github.io/matrix-documentation/API/zwave/)

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

MATRIX Creator is a Z-Wave Plus Hardware Platform Product. It provides communication with the Z-Wave SerialAPI running on the Z-Wave module in the MATRIX Creator. Refer to Sigma design Z-Wave Specification (http://zwavepublic.com/specifications) and developer resources (http://zwavepublic.com/developer).

Exclusion

MATRIX Creator is a Z-Wave Plus Hardware Platform Product. It provides communication with the Z-Wave SerialAPI running on the Z-Wave module in the MATRIX Creator. Refer to Sigma design Z-Wave Specification (http://zwavepublic.com/specifications) and developer resources (http://zwavepublic.com/developer).

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

Special Operations as Z-Wave Controller

As long as this device is not included into a Z-Wave network of a different controller
it is able to manage its own Z-Wave network as primary controller. As a primary controller
the device can include and exclude other devices in its own network, manage associations,
and reorganize the network in case of problems. The following controller functions
are supported:

Inclusion of other devices

Communication between two Z-Wave devices only works if both belong to the same
wireless network. Joining a network is called inclusion and is initiated by a controller.
The controller needs to be turned into the inclusion mode. Once in this inclusion mode
the other device needs to confirm the inclusion – typically by pressing a button.

If current primary controller in your network is in special SIS mode this and
any other secondary controller can also include and exclude devices.

To become
primary a contoller have to be resetted and then include a device.

MATRIX Creator is a Z-Wave Plus Hardware Platform Product. It provides communication with the Z-Wave SerialAPI running on the Z-Wave module in the MATRIX Creator. Refer to Sigma design Z-Wave Specification (http://zwavepublic.com/specifications) and developer resources (http://zwavepublic.com/developer).

Exclusion of other devices

The primary controller can exclude devices from the Z-Wave network. During exclusion
the relationship between the device and the network of this controller is terminated.
No communication between the device and other devices still in the network can happen
after a successful exclusion. The controller needs to be turned into the exclusion mode.
Once in this exclusion mode the other device needs to confirm the exclusion – typically
by pressing a button.

Attention: Removing a device from the network means that it is turned back
into factory default status. This process can also exclude devices from it’s previous
network.

MATRIX Creator is a Z-Wave Plus Hardware Platform Product. It provides communication with the Z-Wave SerialAPI running on the Z-Wave module in the MATRIX Creator. Refer to Sigma design Z-Wave Specification (http://zwavepublic.com/specifications) and developer resources (http://zwavepublic.com/developer).

Technical Data

TemperatureAtmospheric PressureBarometric PressureHumidityLoudnessLuminanceRotationUltraviolet Index
Frequency| XXfrequency
Maximum transmission power| XXantenna

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>