AKAI APC Key 25 Controller with Keyboard User Manual
- June 8, 2024
- AKAI
Table of Contents
AKAI APC Key 25 Controller with Keyboard User Manual
Introduction
Box Contents
- APC Key 25: USB Cable
- Ableton Live Lite (download): User Guide
- Software Download Cards: Safety & Warranty Manual
Support
For the latest information about this product (system requirements,
compatibility information, etc.) and product registration, visit
akaipro.com/apckey25.
For additional product support, visit akaipro.com/support.
Setup
-
Use the included USB cable to connect APC Key 25’s USB port to an available USB port on your computer (powered on).
-
On your computer, open Ableton Live.
-
In Ableton Live, open the Preferences:
• Windows: Options > Preferences
• Mac OS X: Live > Preferences -
Click the MIDI/Sync Tab.
-
Click an available Control Surface drop-down menu and select APC Key 25.
-
Click an available Input drop-down menu and select APC Key 25.
-
Click an available Output drop-down menu and select APC Key 25.
-
Close the Preferences window.
You can now use APC Key 25 with Ableton Live.
Basic Operation
Refer to this section to learn how to do basic tasks in Ableton Live using APC Key 25.
Important: Before doing any of the following, set up APC Key 25 as a controller in Ableton Live (described in the Setup section above).
To launch a clip, press one of the Clip Buttons (in the 8×5 matrix) that is lit amber, which means there is a clip loaded to that slot but is not playing. The Clip Button will light green when it is playing.
To stop a clip:
- Press and hold Shift and press the first Scene Launch Button (Clip Stop). This puts the Clip Stop Buttons at the bottom of the 8×5 matrix of Clip Buttons in Clip Stop Mode.
- Press the Clip Stop Button in the same track (column) as the clip you want to stop.
To launch a scene, press one of the five Scene Launch Buttons to the right of
the 8×5 matrix
of Clip Buttons.
To move around the matrix of clips, press and hold Shift and press one of the left four Clip Stop Buttons (▲ ,▼ ,◄, ► ) to shift the viewable 8×5 matrix. In the software, this is represented by a red rectangle around the clips.
To solo a track:
- Press and hold Shift and press the second Scene Launch Button (Solo). This puts the Clip Stop Buttons at the bottom of the 8×5 matrix of Clip Buttons in Solo Mode.
- Press the Clip Stop Button in the same track (column) as the clip you want to solo.
To record-arm a track:
- Press and hold Shift and press the third Scene Launch Button (Rec Arm). This puts the Clip Stop Buttons at the bottom of the 8×5 matrix of Clip Buttons in Record-Arm Mode.
- Press the Clip Stop Button in the same track (column) as the clip you want to recordarm.
To mute a track:
- Press and hold Shift and press the fourth Scene Launch Button (Mute). This puts the Clip Stop Buttons at the bottom of the 8×5 matrix of Clip Buttons in Mute Mode.
- Press the Clip Stop Button in the same track (column) as the clip you want to mute.
To select a track:
- Press and hold Shift and press the fifth Scene Launch Button (Select). This puts the Clip Stop Buttons at the bottom of the 8×5 matrix of Clip Buttons in Select Mode.
- Press the Clip Stop Button in the same track (column) as the clip you want to select.
To stop all clips, press the Stop All Clips button.
To adjust volumes, press and hold Shift and press the fifth Clip Stop Button
(Volume) to put APC Key 25’s Knobs in Volume Mode. The eight Knobs will
control the volume levels of the first eight tracks in Ableton Live.
To adjust panning, press and hold Shift and press the sixth Clip Stop Button (Pan) to put APC Key 25’s Knobs in Pan Mode. The eight Knobs will control the panning positions of the first eight tracks in Ableton Live.
To adjust send levels, press and hold Shift and press the seventh Clip Stop Button (Send) to put APC Key 25’s Knobs in Send Mode. The eight Knobs will control the levels of Send A for the first eight tracks in Ableton Live.
Tip: Repeat this action to set the knobs to control the levels of subsequent sends (e.g., Send B, Send C, etc.).
To adjust devices, press and hold Shift and press the eighth (last) Clip Stop Button (Device) to put APC Key 25’s Knobs in Device Mode. The eight Knobs will control the eight Macro Controls of the current device in Ableton Live.
Features
- USB Port: Use a standard USB cable to connect this port to a USB port on your computer. The computer’s USB port provides power to APC Key 25. This connection is also used to send and receive MIDI data to and from your computer.
- Kensington Lock Slot: You may use this Kensington lock slot to secure the APC Key 25 to a table or other surface.
- Keyboard: This 25-note keyboard is velocity-sensitive and, in conjunction with the Oct Up and Oct Down buttons, can control a ten-octave range.
- Sustain: Press and hold this button to sustain all currently held notes (similar to the sustain pedal on a piano). This button is a momentary button, sustaining only when the button is pressed and held.
- Oct Down / Oct Up: Use these buttons to shift the keyboard’s range up or down. Press both buttons simultaneously to reset the octave shift to “zero.”
- Play/Pause: Press this to start/resume or pause playback in Ableton Live.
- Rec: Press this to start recording in Ableton Live.
- Stop All Clips: Press this button to stop all clips when they reach the end.
- Clip Stop Buttons: Normally, you can press one of these buttons to stop the clip in the corresponding track—represented by the column of five Clip Buttons just above it.
You can change their functions by pressing and holding Shift and then pressing one of the Scene Launch buttons: Clip Stop, Solo, Rec Arm, Mute, or Select. Each button puts the Clip Stop Buttons in a different mode:
- Clip Stop Mode: The Clip Stop Buttons will stop their corresponding tracks (the default mode).
- Solo Mode: The Clip Stop Buttons will solo their corresponding tracks.
- Record-Arm Mode: The Clip Stop Buttons will record-arm their corresponding tracks.
- Mute Mode: The Clip Stop Buttons will mute their corresponding tracks.
- Select Mode: The Clip Stop Buttons will select their corresponding tracks.
Press and hold Shift and press one of the left four Clip Stop Buttons (▲ ,▼ ,◄, ►) to shift the viewable 8×5 matrix of clips. In Ableton Live’s Session View, this is indicated by a red rectangle around the clips.
10. Knobs: Normally, you can use these knobs to control various
parameters in Ableton Live.
You can use the right four Clip Stop Buttons (Volume, Pan, Send, Device) to
put the knobs in Volume Mode, Pan Mode, Send Mode, or Device Mode.
Press and hold Shift and press one of the right four Clip Stop Buttons (Volume, Pan, Send, Device) to put APC Key 25’s Knobs in the corresponding mode:
- Volume Mode: The eight knobs will control the volume levels of the first eight tracks in Ableton Live.
- Pan Mode: The eight knobs will control the panning positions of the first eight tracks in Ableton Live.
- Send Mode: The eight knobs will control the levels of Send A for the first eight tracks in Ableton Live. Repeat this action to set the knobs to control the levels of subsequent sends (e.g., Send B, Send C, etc.).
- Device Mode: The eight knobs will control the eight Macro Controls of the current device in Ableton Live.
11. Clip Buttons: While in Ableton Live’s Session View, use these buttons in this 8×5 to launch clips. Each Clip Button represents a single clip slot. The eight columns represent eight tracks while the five rows represent five scenes. In Clip Launch Mode, the buttons’ LED colors represent the following:
- Off: Clip is empty.
- Amber: Clip is loaded but not playing.
- Green: Clip is loaded and playing.
- Red: Clip present and recording.
You can launch the entire scene by pressing the Scene Launch buttons to the right of the row of clips.
12. Scene Launch Buttons: Normally, you can press one of these buttons
to launch the corresponding scene—represented by the row of eight Clip Buttons
to its left.
Press and hold Shift and then press one of these buttons to change the
function of the Clip Stop Buttons, which can then stop, solo, record-arm,
mute, or select their corresponding tracks (see #9. Clip Stop Buttons above).
13. Shift: Press and hold this button and then press a Scene Launch button to change the function of the Clip Stop Buttons (see #9. Clip Stop Buttons above).
Press and hold this button and then press one of the left four Clip Stop Buttons (▲ ,▼ ,◄, ►) to shift the viewable 8×5 matrix of clips. In Ableton Live’s Session View, this is indicated by a red rectangle around the clips.
Press and hold Shift and press one of the right four Clip Stop Buttons (Volume, Pan, Send, Device) to put APC Key 25’s Knobs in the corresponding mode (see #10. Knobs above).
Technical Specifications
Trademarks and Licenses
Akai Professional is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries.
Ableton is a trademark of Ableton AG.
Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other
countries.
Windows is a registered trademark of Microsoft Corporation in the United
States and other countries.
Kensington and the K & Lock logo are registered trademarks of ACCO Brands.
All other product or company names are trademarks or registered trademarks of
their respective owners.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>