Godox M200D Photography LED Video Light Instruction Manual

: June 8, 2024
: Godox

Godox M200D Photography LED Video Light

IMPORTANT SAFETY INSTRUCTIONS

When using your photographic equipment, basic safety precautions should always be followed, including the following:

Read and understand all instructions before using.
Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use.
Care must be taken as burns can occur from touching hot parts.
The appliance switch is provided with the symbols 0 indicating off and 1 indicating on. The symbols and may be used for this purpose.
Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged – until it has been examined by a qualified serviceman.
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.
Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Never yank cord to pull plug from outlet Grasp plug and pull to disconnect.
Let appliance cool completely before putting away. Loop cord loosely around appliance when storing.
To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
To reduce the risk of electric shock, do not disassemble this appliance, but take it to a qualified serviceman when service or repair work is required. Incorrect reassembly can cause electric shock when the appliance is used subsequently.
The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury to persons.
Connect this appliance to a grounded outlet
Disconnect this unit from its source of supply before replacing the projection lamp.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to flt in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

SAVE THESE INSTRUCTIONS

Foreword
Thank you for purchasing’ Godox M200D/M300D is a LED Light product with superior performance. It has a separation design of light body and controller. high brightness, low consumption, high power, ultra-high CRI and various dimming curves functions, quite suitable for large photo studios, broadcast studios, outdoor or large-scale field scenes.

Features:

Strong power to create bright light output
0%-100% step less brightness adjustment controls the brightness in subtle scenes.
4 dimming curves: linear, S-curve, exponential, and logarithmic.
Bowens mount is perfectly compatible with more optical accessories.
Various professional control methods: Bluetooth control/DMX512 remote control/2.4G wireless control.
Super high color rendering index: CRle96, TLCle97
12 simulated light effects: flash, lightning, TV, broken bulb, etc.
Two power supply methods: AC power supply (1 00V~240V)and V-mount battery power supply (14.8V or 26V).
The side with yellow battery removal button supports unilateral power supply.
2.4 inches TFT panel,4 buttons, 1 knob, clear UI interface.

Warning

Always keep this product dry. Do not use in rain or in damp conditions.
Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
Keep out of reach of children.
As this product do not have waterproof function, please take measures of waterproof in rainy or damp environment.
Do not leave or store the product if the ambient temperature reads over 40°C.
Do not use the product in the presence of flammable gases, chemicals and other similar materials.
CAUTION: Hot parts1When the product is always on and flickering. please do not touch the high temperature part of the LED head.
When replacing product accessories. please turn off the LED light and perform a cold cut.
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
The lamp shall be changed if it has become damaged or thermally deformed.
The luminaire is intended for professional use only.

Name of Body

Light Body

Light Body Screen Print
Bowens Mount
LED Bead
Metal U-bracket
Mount Fixing Pusher
DC INPUT Port
Handle Direction Adjustment Button
Locking handle
Sleeve Knob

Controller

Black Battery Removal Button
V- mount Battery Box
AC INPUT Port
48V DC Port
Yellow Battery Removal Button
Fan Switch Button
/FX Button
Menu Button
Power Switch Button
SET Adjustment Knob
DC OUTPUT Port
DMX IN XLR Port
DMX OUT XLR Port

Remote Control {Separately Sold Accessory)

Power Switch Button
SET Setting Button
Reduction Button
CH / GR Button
Increase Button
RST- Reset Mark(Press Reduction Button and Increase Button simultaneously to reset)

What’s in the Box (M300D/M200D)

Light Body *1
Connecting Cord *1
5m Power Cord *1
Controller Clamp *1
Connecting Cord Fixed Rope *1
Lamp Cover *1
Carry Bag CB49 *1
Controller *1
Bowens-mount Reflector RFT-19 *1
Instruction Manual *1

Separately Sold Accessories

Better shooting effects and using experience matched with following accessories: Fresnel Attachment for COB LED lights, RC-A6 Remote Control. Safety Wire Rope and Spotlight Attachment.

Installation and Disassembly Guide

Connect the Controller and Light Body
Press and hold the spring latch button of the connecting cord, insert the connecting cord into the DC INTPUT Port of the light body, insert the other end of the connecting cord into the DC OUTPUT Port of the controller to complete the connection.
Mount on the tripod
Adjust the light body to a proper angle, rotate the screw of sleeve knob to install the light body on the tripod, then rotate the screw of sleeve knob to fix the light body on the tripod.
The inclination angle of the light body could be adjusted by loosening the bracket angle adjustment handle and then screwing down the handle afterwards.
Note: The tripod belongs to separately sold accessories.
Tips: Press the handle direction adjustment button to adjust the handle by 360′.
Mount on the light stand
Loosen the handle of the controller clamp, then insert the light stand and rotate the handle to tighten. Finally, insert the V port of the controller into the clamp slot.
Tip: Press and hold the mount fixing pusher can easily remove the controller.
Installation and disassembly the lamp cover Installation:
Press the Mount Fixing pusher top-down, put the lamp cover on Bowens Mount, and rotate clockwise to tighten it.
Disassembly: Press the Mount Fixing pusher top-down, then rotate counterclockwise to remove it.
Note: Make sure to remove the lamp cover before use to avoid overheating damage. Put on the lamp cover to protect the lamp when not in use.
Installation and disassembly the standard reflector
Installation: Press the Mount Fixing pusher top-down, put the reflector on Bowens Mount, and rotate clockwise to tighten it.
Disassembly: Press the Mount Fixing pusher top-down, then rotate counterclockwise to remove it.

Connect to DMX Controller

The Connection operation diagram of Controller and DMX Controller is as follows:

Power Supply

AC Power Supply

Note: Please press the latch button when installing or disassembling the power cord and connecting cord.
V-mount battery power supply

Note: The light can be supplied by 14.BV or 26V V-mount battery. Only the side with yellow battery removal button supports unilateral charging, one with. When it is powered by two batteries and one of which is low, the device still can’t work normally even if the other one is full. The corresponding battery icon will blink in low battery mode. It is recommended to check whether both batteries have sufficient power when using two batteries.

Display Screen

Controller Operation Instruction

Turn On/Off
Press the controller< > Button for 1 second after connecting to the power supply to turn on or off.
Brightness Adjustment
Turn the SET adjustment knob on the main interface to adjust brightness from 0% to 7 00%, with an increment of 1 % in each level. Rotate clockwise to increase brightness, and counterclockwise to decrease brightness. The brightness will increase or decrease by 1 % unit in normal rotation speed; and increase or decrease by 10% unit in rapid rotation speed.

Note: Short press the SET adjustment knob once in main interface can turn off the light brightness, press again to resume the light brightness.
Menu Setting
Short press< MENU> Menu Button to enter the menu interface, displayed in order with Wireless, Bluetooth, OMX, Fan, Dimmer, Screen Bright, Language, Reset, Version & Upgrade.
Turn and short press the SET adjustment knob on the menu interface to select and enter the corresponding setting options interface.
Wireless The Wireless interface is displayed in order with Wireless Switch, Channel, Group and ID. Short press & turn the SET adjustment knob to complete the settings of Wireless Switch, Channel, Group and ID.
Bluetooth
The Bluetooth interface is displayed in order with Bluetooth Switch, Reset and MAC Code.
Short press & turn the SET adjustment knob to complete the settings of Bluetooth Switch and Bluetooth Reset.

For more smartphone APP operations, please open the “help” in “Godoxlight”APP to gain detailed guidance.

Note: the APP can be used directly on the firstly installed device (smartphone or tablet). When changing to other mobile device, the light shall be reset before the normal usage of APP.
DMX
The DMX Setting interface is displayed with Address. Turn the SET adjustment knob to choose address from OFF or l -512, the light will be in DMX OFF or ON rnode respectively. Afterwards, short press the SET adjustment knob to return to the previous menu interface.

DMX Practical Form

Address Code / Operation Mode	CCT	FX
n(Mode)	0-51	52-255
n+l	DMX•(l 00/255) Integer 0-100% brightness adjustment	DMX•(l 00/255)

Integer 0-100% brightness adjustment
n+2| | OMX• (Total Light Effect/255)

For Example: Total Light
Effect 8,DMX=l 60, Light
Effect N0. 0 l 60•8/255°5

n+3| 0-85: Light Effect Level I
86-177: Light Effect Level II
172-255: Light Effect Level Ill|
n+4| |
n+5| |

Fan
Turn the SET adjustment knob on the Fan interface to choose from AUTO, OFF, LOW, HIGH modes.
Note: Enter mute mode when turning off the fan. Short press the fan switch button to turn on or turn off the fan
Dimmer
Turn the SET adjustment knob on the Dimmer interface to choose linear/S-curve/exponential/ logarithmic dimming curve.
Screen Bright
Turn the SET adjustment knob on the Screen Bright interface to choose l, 2, 3 levels of screen brightness.
Language
Turn the SET adjustment knob on the Language interface to choose English or Simplified Chinese.
Reset
Turn the SET adjustment knob on the Reset interface to choose “Yes” or “No” and short press to confirm. If you choose “Yes”, the system will initiate resetting program and resetting progress bar is displayed on the screen, after which it will return to the main interface.
Version & Upgrade
The Version Code displayed on the Version & Upgrade interface is the firmware version of the product.

Light Effect Setting

Short press < /FX> button to enter FX Light Effect interface, turn the SET adjustment knob to choose flash, lightning, broken bulb or 1V scenes.
Note: Short press the SET adjustment knob to change the rate and adjust brightness after choosing one of the above Light Effects.

Connecting Cord Issue

When the connecting cord is not correctly connected to the light or controller, a separated icon of connecting cord and device is displayed on the panel. Please check the connecting ports of the controller and light.

Switch from AC Power Supply to V-Mount Battery Power Supply

Unplug the power cord and install V-mount battery then turn on the product.

Note: If you install the V-mount battery before unplugging the power cord, and the brightness value is set higher than the maximum brightness that the battery can be turned on, then you switch to V-mount battery power supply by unplugging the power cord, the light and the controller will automatically power off. The machine can only resume normal operation after reboot.

Maximum Brightness of M200D in Different States

CCT mode: Maximum Brightness(%) in Auto Cooling Mode or High-Speed Cooling Mode when supplied by V-mount battery

V-mount battery	linear	S-curve	exponential	logarithmic
14.BV(single)	40%	42%	70%	10%
14.BV(double)	80%	55%	90%	30%
25V(single)	80%	55%	90%	30%
14.8V+26V	100%	100%	100%	100%
26V(double)	100%	100%	100%	100%

CCT mode: Maximum Brightness(%) in Fan Off Mode when supplied by V-mount battery

V-mount battery	linear	S-curve	exponential	logarithm ic
14.BV(single)	20%	38%	60%	7%
14 8V(double)	20%	38%	60%	7%
26V(single)	20%	38%	60%	7%
14.8V+26V	20%	38%	60%	7%
26V(double)	20%	38%	60%	7%

CCT mode: Maximum Brightness (%) in Low-Speed Cooling Mode when supplied by V-mount battery

V-mount battery	linear	S-curve	exponential	logarithmic
14.BV(single)	40%	42%	70%	70%
14 8V(double)	60%	48%	80%	18%
26V(single)	60%	48%	80%	18%
14.8V+26V	60%	48%	80%	18%
26V(double)	60%	48%	80%	78%

CCT mode: Maximum Brightness(%) in different Fan Mode when supplied by AC power

Fan Mode	linear	S-curve	exponential	logarithmic
Auto Cooling	100%	100%	100%	100%
Off	20%	38%	60%	7%
Low-Speed Cooling	60%	48%	80%	18%
High-Speed Coo ling	100%	100%	100%	100%

FX mode: Maximum Brightness(%) in different Fan Mode when supplied by AC power

Auto Cooling	100%
Off	20%
Low-Speed Cooling	60%
High-Speed Coo ling	100%

FX mode: Maximum Brightness (%) in different Fan Mode when supplied by V-mount battery

V-mount battery	Auto Cooling	Off	Low-Speed Cooling	High-Speed Cooling
14.SV(single)	40%	20%	40%	40%
14 SV(double)	80%	20%	60%	80%
26V(single)	80%	20%	60%	80%
14.8V+26V	100%	20%	60%	100%
26V(double)	100%	20%	60%	100%

Maximum Brightness of M300D in Different States

V-mount battery	linear	S-curve	exponential	logarithmic
14.SV( single)	30%	40%	65%	8%
14.SV(double)	60%	48%	80%	20%
26V(single)	60%	48%	80%	20%
14.8V+26V	90%	65%	95%	50%
26V(double)	100%	100%	100%	100%

CCT mode: Maximum Brightness(%) in Fan Off Mode when supplied by V-mount battery

V-mount battery	linear	S-curve	exponential	logarithmic
14.SV(single)	20%	38%	60%	7%
14 SV(double)	20%	38%	60%	7%
26V(single)	20%	38%	60%	7%
14.8V+26V	20%	38%	60%	7%
26V(double)	20%	38%	60%	7%

CCT mode: Maximum Brightness(%) in Low-Speed Cooling Mode when supplied by V-mount battery

V-mount battery	linear	S-curve	exponential	logarithmic
14.8V(single)	30%	40%	65%	8%
14.8V(double)	60%	48%	80%	20%
26V(single)	60%	48%	80%	20%
14.8V+26V	60%	48%	80%	20%
26V(double)	60%	48%	80%	20%

CCT mode: Maximum Brightness(%) in different Fan Mode when supplied by AC power

Fan Mode	linear	S-curve	exponential	logarithmic
Auto Cooling	100%	100%	100%	100%
Off	20%	38%	60%	7%
Low-Speed Cooling	60%	48%	80%	20%
High-Speed Cooling	100%	100%	100%	100%

FX mode: Maximum Brightness(%) in different Fan Mode when supplied by AC power

Auto Cooling	100%
Off	20%
Low-Speed Cooling	60%
High-Speed Cooling	100%

FX mode: Maximum Brightness (%) in different Fan Mode when supplied by V-mount battery

V-mount battery	Auto Cooling	Off	Low-Speed Cooling	High-Speed Cooling
14.SV(single)	30%	20%	30%	30%
14 SV(double)	60%	20%	60%	60%
26V(single)	60%	25%	60%	60%
14.8V+26V	90%	20%	60%	90%
26V(double)	100%	20%	60%	100%

Note: The dimming curve is not adjustable in FX mode, it is linear in default. The above data is based on 26V 270Wh 10.5Ah battery and 14.8V 150Wh 10.2Ah battery.

Software Upgrade

Download the new firmware to the U disk from the official website (http://www.godox.eom.cn/Downloads.html).
Turn off the LED light. Insert the U disk with new firmware into the USB upgrade port.
Turn on the LED Light. and it will automatically enter the upgrading interface ..
It will return to main interface after completion.

Notes:

New firmware must be downloaded from the official website, and keep only one BIN file in the root directory of the USB disk.
The USB port can only support firmware upgrade function.

Over-Temperature Protection

If the temperature of the light body is too high, the Over-Temperature Protection icon flashes on the main interface, the light body can be used normally.
If the temperature of the light body exceeds the limit of Over-Temperature Protection, the Over-Temperature Protection icon flashes on the main interface and the screen works properly after the light goes out in 3 seconds. When the temperature decreases to 50″C, the Over-Temperature Protection icon disappears, then the light body can resume working.

Fan Troubleshooting

If icon appeared and blinking and fan off icon is also appeared on the display, It might be the fan failure. Please contact with customer service.

Maintenance

This product, except consumables e.g. adapter and power cable, is supported with a one-year warranty.
Maintenance of the light must be performed by our authorized maintenance department which can provide original accessories.
Unauthorized service will void the warranty.
If the product breaks down or gets wet, please do not use it until repaired by professionals.
If there is anything abnormal during LED light’s working, please turn it off immediately and identify the reasons.

Illuminance Testing Data

M200D

Testing Conditions| Illuminance Unit| l m| 2 m| 3 m

Bare lamp

| lux| 8430| 2210| 1080
fc| 784| 205| 100
With reflector| lux| 98500| 20500| 8850
fc| 9151| 1904| 822

M300D

Testing Conditions| Illuminance Testing Data| l m| 2 m| 3 m

Bare lamp

| lux| 12300| 3790| 1540
le| 1140| 293| 143

With reflector

| lux| 99100| 21100| 8980
fc| 9200| 1960| 835

Note: The above tests are all based on the condition of 100% brightness.

Technical Data

Mode	M200D	M300D
Power	230W (Max)	330W(Max)
Light Head Input	48V/4.7A	48V/7A
Controller AC Power Input	100-240V~50/60Hz
Controller Power Input	DC48V
V-mount battery (optional) Specifications	14.SV, l 50Wh / 26V 270Wh
Channel	32(1~32)
Group	16(0~9, A~F)
ID	1~99, OFF
Color-Temperature	5600K
CRI	≥ 96
TLC I	≥ 97
Working Environment Temperature	-20 C~40’C
FX Light Effect	12 kinds within 4 types
Controlling Method	Support DMX512, 2.4G Wireless Control, Bluetooth APP
Dimming Curve	4 types: linear/S-curve/ exponential/logarithmic
Mute Mode	YES
2.4G Wireless Control Distance	≈ 60m
Bluetooth Transmission Distance	≈ 30m
Display Screen	2.4 inches
Light Body Dimension	425.1•232.3•141.2mm
Controller Dimension	270.4•123.6•132mm
Light Body Weight	≈ 3.34kg
Controller Weight	≈ 2.74kg
Bluetooth Transmission Frequency	2402 00-2480 00MHz
Maximum Transmit Power	5dbm

Product design and specifications are subject to change without notice.

Maintenance

This product, except consumables e.g. cable, is supported with a one-year warranty.
Avoid sudden impacts and the product should be dedusted regularly.
Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by professionals.
Changes made to the specifications or designs may not be reflected in this manual.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement The device can be used in portable exposure condition without restriction. Declaration of Conformity:
GODOX Photo Equipment Co, Ltd. hereby declares that the This equipment are in compliance with the essential requirements and other relevant provisions of EU Directive 2014/53/EU. They are allowed to be used in all EU member states.
For more information of Doc, Please click this web link:
http://www.godox.com/DOC/Godox__M300D_M200D_DOC.pdf

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

Applicable Products

The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached, etc.) are not included in this warranty scope.

Warranty Period

The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases

The guarantee and service offered by this document are not applicable in the following cases:

The product or accessory has expired its warranty period;
Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc;
Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;
The original identifying information of product or accessory is modified, alternated, or removed;
No valid warranty card;
Breakage or damage caused by using illegally authorized, nonstandard or non-public released software;
Breakage or damage caused by force majeure or accident;
Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.