NINTENDO SWITCH 500-137-1 Afterglow LED Wireless Deluxe Gaming Controller User Guide
- June 8, 2024
- Nintendo Switch
Table of Contents
NINTENDO SWITCH 500-137-1 Afterglow LED Wireless Deluxe Gaming Controller
WARNING:
CHOKING HAZARD – Small parts. Not for children under 3 years.
Initial Setup
First press A/B/X/Y or the Dap to wake the controller. In the home screen, select [Controllers] > [Change Grip/Order]. On the next screen, press and hold the Sync button for at least 2 seconds. Once paired, the player indicator will be illuminated.
Tip: To unpair hold down the sync button for at least 1 second
Charging the Controller
Connect the controller using the micro USB to the dock. The controller will
breathe red while being charged.
Tip: When the controller is low on battery the LED’s will turn off and
blink red every 30 seconds.
Program Back Buttons
Press any button you would like mapped and the function button LED will flash
3 times indicating a successfully mapped function.
While holding down the function button, press the back button you would like to map a function to and the function button LED will start flashing.
TIP: To disable the back button, double tap the back button while holding down the function button.
Light Modes
To cycle though the light modes, hold down the function button and press
either L or R.
Mode 1 – The LEDs are on and set to your color.
Mode 2 – The LEDs fade in and out to set color.
Mode 3 – The LEDs will cycle through all colors.
Mode 4 – The LEDs will react to the movement of the sticks.
Adjusting the Lights
To change the LED color, hold down the Function button and use the Left/Right
on the Dyad to change the color of the LEDs. Save the color setting by
releasing the Function button.
Tip: For a white color hold down the function button and click the left
stick.
To adjust the brightness, hold down the function button and click the ZR/ZL
buttons to increase or decrease brightness. To return to 100% brightness,
cycle though all brightness levels.
LIMITED WARRANTY
-
Coverage and Term
-
DP warrants that this product will be free from manufacturing defects for two years from the
original date of purchase. Manufacturing defects are those defects in materials and/or workmanship, subject to final determination by PDP’s customer service department. This warranty applies only to original purchasers with a valid proof of purchase from an authorized PDP retailer that clearly shows the date of purchase.
Exclusive Remedy and Exclusions -
The exclusive remedy for valid claims will be the repair, replacement or refund of the product. This warranty does not cover defects caused by accidents, improper or abusive use of the product, unauthorized or improper modifications, repairs or handling.
How to Get Service -
Purchasers should contact the PDP customer service department at 800-331-3844 (US and Canada only) or +442036957905 (UK only) or by visiting support.pdp.com or support.pdp-eu.com. Inquiries are typically answered within twenty-four business hours.
Your Rights Under Applicable Law -
This warranty does not affect the legal rights of customers under applicable state, provincial or national laws governing the sale of consumer goods.
Additional Information for Australian Consumers -
DP products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits given to you under our express warranty are in addition to other rights and remedies you have under the Australian Consumer Law and other laws.
FCC AND IC STATEMENT FOR WIRELESS PRODUCTS
CAUTION:
Changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment. The equipment
complies with FCC RF exposure limits set forth for an uncontrolled
environment. The equipment must not be co-located or operating in conjunction
with any other antenna or transmitter. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada,. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
© 2021 Performance Designed Products LLC. PDP, Afterglow and their respective
logos are trademarks and/or registered trademarks of Performance Designed
Products LLC. All rights reserved.
© 2021 Nintendo. Nintendo Switch is a trademark of Nintendo. Licensed by
Nintendo. All rights reserved. All other logos and trademarks are the property
of their respective owners. Please keep this information for future reference.
Need Help?
Visit support.pdp.com or talk to us at (800) 331•3844 (USA and Ccrnc1da only)
or +4420369S790S (UK only).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>