CLEAR WATER II Cartridge Standard System Instruction Manual

CLEAR WATER II Cartridge Standard System

CLEARWATER II CARTRIDGE FILTER SYSTEM OWNER’S MANUAL

Our ClearWater II Cartridge Filter System is shipped from Waterway complete with everything you need right in the box. Assemble filter system only after above-ground pool is installed. Fill pool with water.
Do not raise water level above pool return line.

The pool equipment should be located between pool skimmer and return line. The filtration system should not be closer than 2 ft. and not further than 5 ft. from the pool. The ClearWater II Cartridge Filter System needs to be on a completely flat surface (e.g. patio block, cement slab, etc.). The pump will require a 110 volt/20 amp service.

WARNING: A GFCI is required. Follow national and local building and safety codes.

Before opening shipping carton, make sure box is in the upright position. Inside the carton, you will find:

1. One base
2. One pump (packaged in separate box)
3. One filter
4. Two lengths of 6 ft. hose
5. One bag with fittings

INSTALLATION INSTRUCTIONS

WARNING! READ ALL INSTRUCTIONS AND WARNING LABELS BEFORE OPERATING FILTER!

1. Place filter and base on a level, secure surface. Place the pump on the base to the left of the filter. The pump should now be facing the filter marked “Inlet”. There is no need to disassemble filter or pump assemblies.

2. Open pump trap lid and remove 2″ gasket. Place 2″ gasket into union nut. Hand tighten union nut to suction side of pump (Detail 5).

3. Secure pump to the base using the pin & anchor assemblies (Detail 4).

4. Open fittings bag and remove coupling assembly (Detail 2).
   Assemble 2″ gasket, coupling, coupling O-Ring, and 2″ union nut, and thread into inlet side of filter.

5. Thread 2″ union nut to pump discharge (Detail 3). Thread hose adapter with O-Ring, to pump trap suction side (Detail 1).

6. From the fittings package, remove 11/2″ hose adapter and O-ring (Detail 2). Thread into the outlet side of the filter tank.

7. Remove 4 hose clamps from the fittings bag. Select one of the hose lengths and slip one clamp over the end of hose adapter. Place the end of the hose on to the hose adapter (pump suction) and the other end to the hose adapter end of the pool skimmer. Repeat steps with filter outlet to pool return.

8. Remove the Lid Handle (#4a) from the fittings bag and attach it to the top of the Lid Assembly (#4) as shown (Detail 6). Secure ClearWater Filter to ClearWater Filter Base using #16a Phillips Head Screws (2) (Detail 7 & 8). Fill pool until water level is halfway up length of skimmer throat.

9. Open air release knob. Stand clear from the filter before starting the pump. Plug in and turn on pump. Air will pass out of the filter through the air release knob. Return to filter to close the air release knob only when a steady stream of water (not air or air and water mix) is discharged.
   NOTE: To remove Lid Assembly, take off Filter Nut (#6) insert Filter Wrench (#9a) in notch between Filter Body (#9) and Lid Assembly (#4) twist and separate as shown in Detail 7.

CLEARWATER II CARTRIDGE FILTER SYSTEM REPLACEMENT PARTS

CLEANING INSTRUCTIONS

If the pressure gauge on your filter reads 5 PSI or higher than the original starting pressure, the filter needs to be cleaned. The ClearWater II Cartridge Filter System features the exclusive 1-2-3 Safety Locking System to ensure safe and simple filter maintenance.

1. Turn off pump. WARNING: Never attempt to clean filter while pump is running. This is a pressurized vessel. It could cause severe injury or harm to your person. Plug skimmer and pool return lines or drain pool water level to below pool return line.
2. Slowly open the air release knob on top of filter until the pressure gauge reads “0”. Open drain cap at bottom of filter and allow water to flow.
3. Press the yellow safety latch on the underside of the locking nut and turn the nut counterclockwise to remove the lid. Rinse the cartridge element with a garden hose. There is no need to remove the element from the filter.
4. Reassemble lid and follow startup procedures from original instructions.

My Original Starting Pressure is ____ PSI (Pounds per
Square Inch). I should clean the filter at ____ PSI.

WARRANTY

For product registration visit: www.waterwayplastics.com.
For Warranty questions or claims please contact point of purchase.

Designed,Engineered & Manufactured in the USA.

2200 East Sturgis Road, Oxnard CA 93030 • Phone 805.981.0262 • Fax 805.981.9403
www.waterwayplastics.com
waterway@waterwayplastics.com

References

• Waterway Plastics – Pool & Spa Supplies

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>