SmartCam View RS-SS-1555 Wireless IP Camera User Guide
- June 9, 2024
- SmartCam View
Table of Contents
SmartCam View RS-SS-1555 Wireless IP Camera
INTRODUCTION
Thank you for using SmartCam View. Please setup the camera by following the steps below:
- In order to connect the camera stably, please install it in the range that could strongly accept the Wi-Fi signal of the home wireless router. Before installing the camera, please determine the installation location(flat surface or wall) When the camera is installed in a place where is difficult to obtain Wi-Fi signal, please use a Wi-Fi extender to extend the Wi-Fi network range.
- Connect power adapter to the camera Please keep the wires away from children to avoid any potential danger. In order to get the best image quality, please don’t touch the camera lens with your hands. Please make sure to use the matching power adapter cable, or the camera may not work properly.
APP Installation
- Download the APP
- Download the “SmartCam View” app from the App Store(IOS devices) or Google Play (Android devices).
- Scan the QR code below to download the APP
- Connect the power connector to the camera and plug the power adapter into a power outlet. Wait until the camera status LED turns solid red.
- Create an account and tap “Add Device” to add a device into your device list, follow the instructions to complete the setup.
Recommended system specifications
- Wi-Fi 802.11 b/g/n
- IOS 11.0 or higher
- Android OS 6.0 or higher
Application pre-check function
- Make full use of SmartCam View to monitor your home(the supported functions may be varied by different models) :
- Event notification
- Motion/Human/Vehicle/Package/Sound detection
- Customized real-time monitoring
- Voice intercom
Register an account
- Run SmartCam View,then tap < Sign up>.
- Input user’s information then tap < Get Verification Code>, Verification code will be sent to your email. Input the verification code,read and accept the relevant privacy policy,then tap < Sign up>.
- Return to the login interface, input user name and password, Choose Region, then tap < login>.
- After tap < login> will reach the Home menu.
Adding Device
- Connect power adapter to the camera. Plug the adapter into an outlet. Wait until the camera indicator light on. Tap button < Add Device> in the middle of Home menu .
- Aim the scanning window at the QR code on the camera.
- Tap button < Yes, The LED is already slowly blinking Red> when the camera LED is blinking in red.
- Tap button < CONNECT> to connect camera hotspot
- Select a 2.4 GHz WIFI network for the camera to connect and input the WIFI password, tap button < save> to connect WIFI.
- Waiting for the WIFI connecting
- Device was added successfully and tap < NEXT>
- Set a device name, you can choose or customize a device name you want.
- Choose the accurate region in where you want to setup your devices.
- Please insert micro SD card and tap < NEXT> to format Micro SD. If you forgot to insert Micro SD, you can insert Micro SD and tap < Check again>
- Tap < Format> to format micro SD card.
- Tap < Got it> after formatting successfully.
- Select a desired way to mount the camera according to the installation Guide.
- Tap < Finish> to finish camera configuration.
Mounting the Camera
Mount bullet camera onto a wall
- Rotate the camera to adjust the view angle and check it by using the live stream which you can access in the SmartCam View app.
Place cube camera on a table
- Keep a gap of more than 10 inches (25cm) between objects to the side of the camera lens to avoid overexposure caused by infrared light reflection
- Keep a gap of more than 10 inches (25cm) between objects to the side of the camera lens to avoid overexposure caused by infrared light reflection.
Place PT camera on a table
- Keep a gap of more than 10 inches (25cm) between objects to the side of the camera lens to avoid overexposure caused by infrared light reflection
Mount the PT camera on celling
Mount the battery camera onto a wall
- Keep a gap of more than 10 inches (25cm) between objects to the side of the camera lens to avoid overexposure caused by infrared light reflection.
Mount with magnetic bracket
Mount with fixed bracket
Note: Before mounting the camera:
- Unplug the camera power connector from the power adapter.
- Find a spot where the camera can easily reach a power outlet.
- Make sure the camera receives a strong Wi-Fi connection in the spot where you want to mount it so that it can stream video to your SmartCam view app
FCC
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s) and Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC & IC Radiation Exposure Statement:
This equipment complies with FCC and Canada radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>