Hisense HL3215STG Integrated WIFI& Bluetooth BLE Dual-mode Module Instructions
- June 9, 2024
- Hisense
Table of Contents
HL3215STG Integrated WIFI & Bluetooth BLE Dual-mode
Module Instructions
HL3215STG Integrated WIFI& Bluetooth BLE Dual-mode Module
HL3215STG is an integrated WIFI& Bluetooth BLE dual-mode module，BK7231M_QFN32– integrated MCU/WLAN MAC/ Baseband/RF single chip scheme. ARM9 32-bit MCU core, 120MHz main frequency, built-in 256KBRAM.
- Supports 802.11b/G/N WIFI standard.
- Supports 802.11b/ G/N standards, HT-20
- Supports Station, Soft AP, Station+Soft AP
- With 20MHz bandwidth, the maximum transmission rate reaches 72.2Mbps
- Module built-in onboard antenna (for the antenna part, please refer to the antenna specification)
- working voltage：DC 3.3-3.6V，
- Supports BLE 5.2standard，
- Supports 802.11 b/g/n 1×1 protocol
- 802.11b: 1, 2, 5.5, 11
- 802.11g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n HT20: MCS0~7
- Supports STA/AP/Direct/Repeaternetwork model
- Supports SGI、Green-Field Preamble and A-MPDU
- Supports WPA,WPA2,WAPI security regime
- Supports 50 MHz SDIO port
- On – chip 2M FLASH, can be expanded to 4M, support transparent download
Function description
HLW3215-TG is a Wi-Fi module used in home appliances, and the first batch of home appliances are dishwasher and oven. The hardware and software architecture based on the module can realize the networking and the control of home appliances. Dishwasher and oven are controlled by the module to achieve their local control functions. They are connected to the cloud server through Wi-Fi and Bluetooth. Users can control the dishwasher and oven through the mobile terminal App to achieve remote control, and can connect to the Hisense Connectlife intelligent platform with intelligent and convenient use experience. In addition, the module supports OTA upgrades and can also assist in OTA upgrades of the MCU plate for dishwashers and ovens.
We will retain control over the final installation of the modular such that
compliance of the end product is assured. If any hardware modify or RF control
software modify will be made by host manufacturer, C2PC or new certificate
should be apply to get approval,if those change and modification made by host
manufacturer not expressly approved by the party responsible for compliance
,then it is illegal.
The host device must be labeled to display the FCC ID of the module “Contains
FCC ID: 2A9F9HL3215STG”
The devices must be installed and used in strict accordance with the
manufacturer’s instructions as described in the user documentation that comes
with the product.
Any company of the host device which install the modular with modular approval
should perform the test of radiated & conducted emission and spurious
emission, etc. according to FCC part 15C : 15.407,15.247 and 15.209 & 15.207
,15B Class B requirement, Only if the test result comply with FCC part 15C :
15.407,15.247 and 15.209 & 15.207 ,15B Class B requirement，then the host can
be sold legally.
FCC STATEMENT
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices . This
modular cannot be installed in any portable device if without further
certification such as C2PC with SAR. This modular complies with FCC RF
radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This modular must be installed and operated with a
minimum distance of 20 cm between the radiator and user body.
IC warning
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
RF warning statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
IC Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices only. This
modular cannot be installed in any portable device.
This modular complies with IC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This modular must be
installed and operated with a minimum distance of 20 cm between the radiator
and user body.
If the IC number is not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must
also display a label referring to the enclosed module. This exterior label
can use wording such as the following: “Contains IC: 29823-HL3215STG” when the
module is installed inside another device, the user manual of this device must
contain below warning statements;
- This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The devices must be installed and used in strict accordance with the
manufacturer’s instructions as described in the user documentation that comes
with the product.