SKMEI 1464 Men OLED Display Watch User Manual

Table of Contents

SKMEI 1464 Men OLED Display Watch User Manual

INSTRUCTION

B:Synchronous needle function
In the Time mode, press E key to set the needle function, press and hold down E key to move the minutehandquickly

C:Product mode loop

Product mode loop

D:Product function mode

Product function mode

E:Product function settings

Time and date setting function

In the Time mode, press A key for 3 seconds to enter the time setting state. At this time“, 12H”flashes, pressBkey“second”starts to flash,then press B key to select setting item (flashing) as following sequence:
Press C key to increase the selected value, and press D key to decrease the selected value.
Press A key to confirm and return to the Time mode.

Stopwatch and segment timing function

The measurement range is 23 hours 59 minutes 59.99 seconds.
Set stopwatch: In the stopwatch mode, press C key to start running the second, then press C key tostoprunning,press A key to remove when the running seconds stop
When the stopwatch is running, press B key to switch to other display modes,the stopwatchwill continuetomeasure time.

Countdown function

The countdown timer can be set from 1 second to 24 hours. An alarm sounds when the countdownreacheszero.
Press C key to start/stop the countdown; when the countdown stops, press A key,the countdowntimewillautomatically return to the initial setting time.
When the countdown reaches to zero, the alarm sounds for about 10 seconds or until you stopit bypressinganybutton. the countdown time is automatically reset to the initially setting time after the alarmstops.
Timing setting: In the countdown mode, hold down A key for 3 seconds until the “hour”starts toflash, pressBkeyto select setting item (flashing) as following sequence:
Press C key to increase the selected value, and press D key to decrease the selected value.
Press A key to confirm and return to the Countdown mode

Alarm function

Alarm function

In the relative mode, press A key to turn on/off the alarm and Chime Hourly function.
In the Alarm mode, hold down A key for 3 seconds until the“hour”starts to flash, press B key toselectsettingitem (flashing) as following.
Press C key to increase the selected value, and press D key to decrease the selected value.
Press A key to confirm and return to the Alarm mode.

Remarks：

In any mode, the alarm will sound for 10 seconds when it reaches the preset time. During thealarm, pressanybutton can stop ringing.
The intermittent alarm sounds once every 5 minutes, sounds 7 times in total. You can press any keytointerruptthe ringing.
After turned on Chime Hourly function,the watch will beep twice at each hour.

Dual time function

In the Dual time mode, hold down A key for 3 seconds until the “hour”starts to flash, press B key toselectflashingitem.
Press C key to increase the selected value, and press D key to decrease the selected value.
Press A key to confirm and return to the Dual time mode

Pedometer function

In Pedometer mode, press C key to“turn on/pause”the function.
In Pedometer mode,press A key to switch the mode as following
In Pedometer mode,hold down A key for 3 seconds to start setting
Metric/Inch: The default is metric system, press C key to switch to metric or imperial.
Set weight: The default weight is 50kg (20IN), adjustable range: 20-200kg/44-440Lb;
Set step distance: the default step distance is 70cm (154LB), adjustable range: 30-200cm/12-79in;
Press C key to increase the selected value, and press D key to decrease the selected value.Metric/Imperial hasnofast adjust function.
Press A key to confirm and return to the Pedometer mode

Step record query function

In the Step record mode, press C key to query historical data within 7 days, and press A key to viewthedataforacertain day

Compass function

In Compass mode, turn the movement to display the compass angle.
hold down A key for 3 seconds into the Compass calibration mode.
In Compass calibration mode 1,press C key when the arrow points to the 6 position , when OKappearsthenintoCalibration mode 2.
In Compass calibration mode 2, hold the watch upside down ,press C key when the arrowpointstothe12position, when OK appears then the calibration is completed and back to the Compass mode.
Magnetic declination correction
Press C key to increase the selected value, and press D key to decrease the selected value.
Press A key to confirm and return to the Compass mode.