BOSE 772238-0110 PowerMatch Amplifiers User Manual
- June 9, 2024
- Bose
Table of Contents
BOSE 772238-0110 PowerMatch Amplifiers User Manual
Installation Information
Thank you for selecting Bose® Power Match® amplifiers. This document is intended to provide professional installers with basic installation and safety guidelines for using the Amp Link Digital Input Card accessory with Power Match® amplifiers. Please read this document before attempting installation.
The INPUT RJ-45 connector receives up to 24 digital channels from a Bose AmpLink product. The amp also supports a THRU path for daisy-chaining all 24 digital audio channels to other Bose Amp Link products, at a maximum distance of 10 m between products.
CAUTION: Shielded EIA/TIA 568B straight CAT 5 cable, or equivalent, is required for proper Amp Lin operation. Un shielded cable is not supported and may cause Amp Link audio to operate improperly. Do NOT connect either of RJ-45 ports to an Ethernet-based network.
To install the AmpLink Digital Input Card:
-
Turn off and unplug the amplifier.
-
Detach the rear expansion slot cover plate by removing the two screws. See Fig. 1.
Fig. 1. Remove cover plate from rear expansion slot -
Align the AmpLink card with the plastic card guides in the open slot; insert until the rear panel is flush with the rear of the amplifier. See Fig 2.
Fig. 2. Insert AmpLink card into amplifier -
Screw the card into place.
-
Set the channel select switch appropriately.
-
Plug in the power cord and turn on the amplifier.
-
Using the front panel, navigate to the FIRMWARE VERSION screen (MAIN MENU>UTILITY>FIRMWARE VERSION).
-
Check the amplifier LCD screen to view whether the AmpLink card has been identified. See Fig 3.
Fig. 3. Amplifier LCD screen after AmpLink card is installed -
If the card does not appear in the FIRMWARE VERSION screen, repeat steps 1 through 7. Be sure that the card is completely pushed into the slot and that the card is properly aligned with the card guides
Safety Information
AUTION: This product is intended for installation by
professional installers only!
CAUTION: Make no modification to system or accessories. Unauthorized alterations may compromise safety, regulatory compliance, and system performance.
CAUTION: This accessory is for use with Bose PowerMatch amplifiers only
CAUTION: Electro-Static Discharge (ESD) sensitive device. Handle with care.
Regulatory Information
This product conforms to all applicable EU directive requirements. The complete declaration of conformity can be found at: www.Bose.com/compliance
This product conforms to all applicable Electromagnetic Compatibility Regulations 2016 and all other applicable UK regulations. The complete declaration of conformity can be found at: www.Bose.com/compliance
Customer Support
China Importer: Bose Electronics (Shanghai) Company Limited, Level 6,
Tower D, No. 2337 Gudai Rd. Minhang District, Shanghai 201100
UK Importer: Bose Limited Bose House, Quayside Chatham Maritime, Chatham,
Kent, ME4 4QZ, United Kingdom
EU Importer: Bose Products B.V., Gorslaan 60, 1441 RG Purmerend, The
Netherlands
Mexico Importer: Bose de México, S. de R.L. de C.V. , Paseo de las Palmas
405-204, Lomas de Chapultepec, 11000 México, D.F. For importer &
service information: +5255 (5202) 3545
Taiwan Importer: Bose Taiwan Branch, 9F-A1, No. 10, Section 3, Minsheng
East Road, Taipei City 104, Taiwan.
Phone Number: +886-2-2514 7676
Your product is covered by a limited warranty. Visit pro.Bose.com for
warranty details.
Bose Corporation
Framing ham, MA 01701 USA
Corporate Center: 508-879-7330
Americas Professional Systems,
Technical Support: 800-994-2673
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>