HILTI HIT-HY 200-A V3 Injectable Adhesive Anchors Instruction Manual
- June 4, 2024
- HILTI
Table of Contents
HIT-HY 200-A V3 Injectable Adhesive Anchors
Instruction Manual
qr.hilti.com/manual/?id=2334935
HIT-HY 200-A V3 Injectable Adhesive Anchors
Hilti HIT-HY 200-A V3
Hilti HIT-HY 200-R V3
|
---|---
Warning
Contains: hydroxypropyl methacrylate
(A) 2,2‘-(m-tolylimino)diethanol (A) 1,4-Butanediol-methacrylate (A) dibenzoyl
peroxide (B) May cause an allergic skin reaction. (A, B) causes serious eye
irritation. (B) Very toxic to aquatic life with long-lasting effects. (B)
Hilti HIT-HY 200-A/R V3
The latest version is available online, use the QR code on the front page
1 Uncracked concrete;
2 Cracked concrete;
3 Grout-filled CMU;
4 Dry base material;
5 Water saturated base material;
6 Waterfilled borehole in concrete;
7 Threaded rod, Threaded sleeve;| 8 Rebar;
9 HIT-Z, HIT-Z-R;
10 Hammer drilling;
11 Hollow drill bit;
12 Diamond coring;
13 Roughening tool;
14 Temperature of base material;| 15 cartridge temperature;
16 Working time;
17 Curing time;
18 Roughening time;
19 Blowing time;
20 ECO mode;
21 Automatic filter cleaning
---|---|---
Hilti HIT-HY 200-A/R V3
Adhesive anchoring system for rebar and anchor fastenings in concrete.
Hilti HIT-HY 200-A/-R V3
Contains: hydroxypropyl methacrylate (A) 2,2‘-(m-tolylimino) diethanol (A)
1,4-Butandioldimethacrylat (A) dibenzoyl peroxide (B)
-
Warning May cause an allergic skin reaction. (A, B)
-
Causes serious eye irritation. (B)
-
Very toxic to aquatic life with long-lasting effects. (B)
-
Do not get in eyes, on skin or on clothing.
-
Wear eye protection, protective clothing, and protective gloves.
-
IF ON SKIN: Wash with plenty of water.
-
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
-
If skin irritation or rash occurs: Get medical advice/attention.
-
If eye irritation persists: Get medical advice/attention.
Disposal considerations: Empty packs: Leave the mixer attached and dispose of
via the local Green Dot recovery system or EAK waste material code: 150102
plastic packaging Full or partially emptied packs: Must be disposed of as
special waste in accordance with official regulations. UK waste material code:
08 04 09 waste adhesives and sealants containing organic solvents or other
dangerous substances. or EAK waste material code: 20 01 27 paint, inks,
adhesives, and resins containing dangerous substances.
Product Information: Always keep these instructions together with the product
even when given to other persons. Material Safety Data Sheet: Review the MSDS
before use. Check expiration date: See imprint on foil pack manifold
(month/year). Do not use expired products. Foil pack temperature during usage:
0 °C to 40 °C / 32 °F to 104 °F. The base material temperature at the time of
installation: HAS-U, HIT-V, HIS, Rebar: between -10 °C and 40 °C / 14 °F and
104 °F.; HIT-Z: between +5°C and 40°C / 41°F and 104°F. Conditions for
transport and storage: Keep in a cool, dry, and dark place between 5 °C and 25
°C / 41 °F and 77 °F.
For any application not covered by this document / beyond the values
specified, please contact Hilti. Partly used foil packs must remain in the
cassette and has to be used within 4 weeks. Leave the mixer attached to the
foil pack manifold and store it within the cassette under the recommended
storage conditions. If reused, attach a new mixer and discard the initial
quantity of anchor adhesive.
Failure to observe these installation instructions, use of non-Hilti anchors,
poor or questionable concrete conditions, or unique applications may affect
the reliability or performance of the fastenings.
NOTICE
The surface of the HIT-Z anchor rod must not be altered in any way.
The thread of HIT-Z must stay free from dirt and dust during the
installation procedure and its cones must be fully embedded into mortar
(especially at minimum embedment). Torque moment must always be applied on
HIT-Z nut and washer installed above a solid baseplate laying on concrete.
Improper handling may cause mortar splashes.
Always wear safety glasses, gloves, and protective clothes during
installation. | Never start dispensing without a mixer properly screwed on. |
Attach a new mixer prior to dispensing a new foil pack (ensure a snug fit). |
Use only the type of mixer (HIT-RE-M) supplied with the adhesive. Do not
modify the mixer in any way. | Never use damaged foil packs and/or damaged or
unclean foil pack holders (cassettes).
**Poor load values / potential failure of fastening points due to
inadequate borehole cleaning.
Hilti hollow drill bits TE-CD, and TE-YD must be used in conjunction with a
properly maintained Hilti vacuum cleaner with model and suction capacity
(volumetric flow rate) as specified in the accessory table. | The boreholes
must be free of debris, dust, water, ice, oil, grease and other contaminants
prior to adhesive injection. | For blowing out the borehole – blow out with
oil-free air until the return air stream is free of noticeable dust. | For
flushing the borehole – flush with water line pressure until water runs clear.
| For
brushing the borehole – only use a specified wire brush. The brush must resist
insertion into the borehole – if not the brush is too small and must be
replaced. | Important! Remove all water from the borehole and blow out with
oil-free compressed air until the borehole is completely dried before mortar
injection. | Do not exceed the roughening time when roughening the drilled
hole!
Ensure that boreholes are filled from the back of the borehole without
forming air voids.
If necessary use the accessories/extensions to reach the back of the borehole.
| For overhead applications use the overhead accessories HIT-SZ and take
special care when inserting the fastening element. The excess adhesive may be
forced out of the borehole. Make sure that no mortar drips onto the installer.
| In water-saturated concrete, it is required to set the anchor immediately
after cleaning the borehole.
Not adhering to these setting instructions can result in failure of
fastening points!**
Made in Germany
Hilti = registered trademark of
Hilti Corporation, Schaan, Liechtenstein
www.hilti.group
© 2022 Right of technical changes reserved S.E. & O
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>