AUDIENT AUEVO16 Evo 16 24×24 USB Audio Interface User Guide

AUDIENT AUEVO16 Evo 16 24×24 USB Audio Interface

SAFETY & WARNINGS

• Unplug the power plug before cleaning. Wipe any dust on the surface with a slightly damp cloth being careful not to allow water into any of the internal parts.

• Do not use any corrosive or abrasive materials to clean this product.

• Check carefully to ensure correct and complete assembly before using.

• Familiarise yourself with all functions and settings of the product before first use.

• Do not allow children to play with or on the product.

•  There may be a slight noise caused by the V-ribbed belt or brake system; this is normal and will not have any effect on the use of the equipment.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Do not allow cleaning or user maintenance to be undertaken by children without supervision.

• Do not attempt to repair this product yourself. If the product or its power supply experiences any malfunction or damage, cease use it immediately and contact
  help.Kogan.com for support.

• Ensure there are no hazards in the operating environment. Always be careful with the packaging materials to avoid any possible danger, e.g. the plastic bag may lead to choking hazard to children.

• Retain the original packaging (if possible) for use in future transportation.

• Dispose of this product responsibly as electronic waste and not with the general household rubbish collection.

COMPONENTS

ATTENTION: The drawings below are for guidance only and they may differ slightly from the product and fittings received. Contact Kogan.com should you have any queries.

ASSEMBLY

• Step 1: Attach the lifting columns to the tabletop.
  Secure the tabletop (1) to the lifting columns (2) with the x8 M8 bolts (B) and tighten using the Allen key (C).
  CAUTION: Avoid placing the glass surface directly on the ground during installation to prevent scratching or denting.

• Step 2: Install the feet.
  Attach the feet (3) to the lifting columns with the x8 M6 screws (A) and tighten using the Allen key (C).

• Step 3 : Connect the motor and power cables.

  • From underneath the desktop, connect the motor plug to the control box.
  • Connect the power cable to the power adapter. Connect the other end of the power cable to a power outlet.
  • The motor and power cable can be secured in place using the supplied cable clamp.

OPERATION

Control Panel

1. Up/Down buttons: Press the “UP/DOWN” buttons to adjust the height of the desk. Press and hold the “UP/DOWN” buttons for more than 2 seconds to continuously adjust the height of the desk. The screen will display “bot” when the desktop is at its lowest point and “top” when the desktop reaches its highest point.

2. Memory buttons (1, 2, 3, 4): Press and hold the desired button for 3 seconds to save the current desk height to the relevant key.

3. Reset: Press the “3 & 4” buttons simultaneously; the screen will display “RST”. Continue holding the “3 & 4” buttons to factory reset the unit.

4. The desk has two USB-A ports and one USB-C port. These ports can be used to supply power to other electronics and support charging protocol.

   • USB-C output: 5V3A/9V2A/12V1.5A
   • USB-A output: 3.6-6.5V2.4A/6.5-9V2A/12V1.5A
   • Total output power of single port : 18W Max
     When the desk is lifting, the output will be stopped, when the lifting stops, the output will restart.

5. Short press the “LOCK” button to enable the child lock function to avoid accidental adjustment and guarantee the safety of children. The screen will show “Loc” when the desk is locked; short press the “LOCK” button again to unlock the desk.

6. Press and hold the up and down button simultaneously to adjust the sensitivity of the anti-collision function. The anti-collision function will be disabled when the screen shows “A-0”, and the sensitivity can be set between levels 1-3 from least to most sensitive, with the screen showing “A-1” to “A-3” accordingly.

TROUBLESHOOTING

• Reset: When the screen displays “ ”, press and hold the “DOWN” button until the desk reaches its lowest point and rebounds to stop. This means the reset is finished.
• If the reset function fails and the screen displays “E01” or “E02”, retry 18 mins later.
• If the “DOWN” button does not work, check all cable connections are secure and then disconnect power to the unit for at least 10 seconds. Reconnect the power and when “ ” appears on the screen, press and hold the “DOWN” button to start the reset process again.
• If the above processes do not resolve the issue, contact help.Kogan.com for support.

Common fault treatment
The following tips will help you detect and eliminate common faults and errors. If the fault you encounter is not listed below, please contact help.Kogan.com. Do not attempt to disassemble or repair the product yourself.

No response while pressing “UP or DOWN” button after connecting the power supply

| 1.              Ensure all cables are properly connected

2.              Contact help.Kogan.com

Rising at a low speed

| 1.              Check if overloaded, max loading: 50kg

2.              Contact help.Kogan.com

The motor does not move as instructed| Contact help.Kogan.com

Desk descends but will not ascend

| 1.              Check if overloaded, max loading: 50kg

2.              Contact help.Kogan.com

Desk slides downwards

| 1.              Check if overloaded, max loading: 50kg

2.              Contact help.Kogan.com

Frequent repositioning required

| 1.              Check if overloaded, max loading: 50kg

2.              Contact help.Kogan.com

Overwork

(Duty cycle: Max. 2min on/18min off)

| 1.              Reset after suspending for 18mins while connected to power

2.              Contact help.Kogan.com

If the LED screens displays “E07, E20 or E22”, this means that button signals aren’t being received| Ensure motor cables are properly connected. If cables are connected, control box or motor may be faulty. Contact help.Kogan.com

SPECIFICATIONS

• Max. weight capacity 50kg
• Height range 720-1210mm
• Drawer stroke 230mm
• Charging ports x2 USB-A, x1 USB-C (DC 5V/2.4A)
• Child lock Yes
• Power supply AC100V-240V, 50/60Hz
• Operating environment 0-40°C

Disposal

This marking indicates that this appliance should not be disposed with other house-hold wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. This marking indicates that this appliance should not be disposed with other house-hold wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

Need more information?
We hope that this user guide has given you
the assistance needed for a simple setup.
For the most up-to-date guide for your product,
as well as any additional assistance you may require, head online to help.kogan.com

References

• Audient - Home
• ARC - EVO
• EVO 16 - 24in | 24out Audio Interface - A new way of doing things
• Nikabe | Kjell.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>