ANALOG DEVICES EVAL-ADG1412L Evaluation Board User Guide

Evaluating the ADG1412L 1.5 Ω RON, Quad SPST Switch
with 1.2 V and 1.8 V JEDEC Logic Compliance
User Guide | EVAL-ADG1412L
UG-2055

FEATURES

• Single inline headers provide flexibility for the field programmable gate array or microcontroller 1.2 V or 1.8V logic-input signals
• Surface-mount device pin resistor or capacitor sockets available for the addition of passive components
• SMB connector sockets provide flexibility for the input and output signals

EVALUATION KIT CONTENTS

• EVAL-ADG1412LEBZ evaluation board

DOCUMENTS NEEDED

• ADG1412L data sheet
• EVAL-ADG1412LEBZ user guide

EQUIPMENT NEEDED

• DC voltage source (VDD/VSS)
• ±15 V for dual supply
• Optional digital logic supply (VL)
  • 1.1 V to 1.3 V for 1.2 V logic
  • 1.65 V to 1.95 V for 1.8 V logic
• Analog signal source
• Method to measure voltage, such as a digital multimeter

GENERAL DESCRIPTION

The EVAL-ADG1412LEBZ is the evaluation board for the ADG1412L. The ADG1412L contains four independent SPST switches, and these switches are turned on with Logic 1. Each switch conducts equally well in both directions when on, and each switch has an input signal range that extends to the supplies. In the off condition, signal levels up to the supplies are blocked.
An external VL supply pin provides logic-control flexibility for lower logic controls. The ADG1412L is both 1.2 V and 1.8 V JEDEC standard compliant.
Figure 1 shows the EVAL-ADG1412LEBZ in a typical evaluation setup. The EVAL- ADG1412LEBZ is located in the center of the evaluation board. Four test points and Subminiature Version B (SMB) sockets are provided to connect to each of the source pins. Three screw terminals power the device. A 5-pin header is provided for the user-defined digital voltage, if required.
Full specifications on the ADG1412L are available in the ADG1412L data sheet available from Analog Devices, Inc., and must be consulted in conjunction with this user guide when using the EVAL-ADG1412LEBZ.

EVALUATION BOARD PHOTOGRAPH

EVALUATION BOARD HARDWARE

POWER SUPPLY
Connector P1 provides access to the supply pins on the ADG1412L Datasheet and Product Info | Analog Devices. VDD, GND, and VSS on P1 link to the appropriate pins on the ADG1412L. For dual-supply voltages, the EVALADG1412LEBZ can be powered at ±15 V. For single-supply voltages, the GND and VSS terminals must be connected and power by the EVAL-ADG1412LEBZ with 5 V or 12 V. Additionally, 1.1 V to 1.95 V is supplied to the V pin of the ADG1412L.
LINK HEADERS
A number of link options are provided on the EVAL-ADG1412LEBZ that must be set for the required operating conditions before using. Table 1 summarizes the link headers and how these headers are used on the EVAL-ADG1412LEBZ. The functions of these link options are described in detail in Table 2.
Table 1. Link Header Descriptions

Table 2. Link Header Functions

ADG1412L.
Position A selects VL from P2.
Position B selects 0 V or AGND.

SMB CONNECTORS
The parallel interface of the ADG1412L is controlled manually using the link headers of JP9 to JP12, or it can be accessed using the SMB connectors, IN1 to IN4. To use the SMB connectors, remove the JP9 to JP12 link headers.
INPUT SIGNALS
The 2-pin terminal blocks, P3, P4, P5, and P6, are provided to connect to both the source and drain pins of the ADG1412L.
Additional SMB connector pads are available if extra connections are required.
Each trace on the source and drain side includes two sets of 0603 pads, which can place a load on the signal path to ground. A 0 Ω resistor is placed in the signal path and can be replaced with a user-defined value. The resistor combined with the 0603 pads can create a simple RC filter.

EVALUATION BOARD SCHEMATIC AND ARTWORK

|
---|---
|
|

ORDERING INFORMATION

BILL OF MATERIALS
Table 3. Bill of Materials

Reference Designator| Description| Manufacturer| Part Number
---|---|---|---
C4 to C6| 50 V tantalum capacitors, 10 µF, Size D| Kemet| T491D106K050AT
C1 to C3, C7 to C9| 50 V, X7R multilayer ceramic capacitors, 0.1 µF, 0603| TDK| CGA3E2X7R1H104K080AA
C10 to C17| Do not insert (DNI)| Not applicable| Not applicable
R1 to R8| DNI| Not applicable| Not applicable
R9 to R16| Resistors, 0 Ω, 0603, 1%| Yageo| RC0603JR-070RL
J1 to J13| 50 Ω, SMB sockets, DNI| Amphenol| SMB1251B1-3GT30G-50
T1 to T15| Red test points| Keystone Electronics| 5000
TP16 to TP20| Black test points| Keystone Electronics| 5001
P1| Header, right angle, 3.81 mm with plug| Phoenix Contact| 1803280
P2| Through-hole header, 5-position| Samtec| TSW-106-08-G-S
P3 to P6| 2-pin terminal blocks, 5 mm| Phoenix Contact| 1935161
JP9 to JP12| 3-pin single inline headers and shorting links| Harwin| M20-9990345
U1| ADG1412L, 1.5 Ω RON, quad SPST switch with 1.2 V and 1.8 V JEDEC logic compliance| Analog Devices Inc.| ADG1412L Datasheet and Product Info | Analog Devices

ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or
indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

EVAL-ADG1412L
analog.com
©2022 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
One Analog Way, Wilmington, MA 01887-2356, U.S.A.

References

• Mixed-signal and digital signal processing ICs | Analog Devices
• EVAL-ADG1412L Evaluation Board | Analog Devices
• ADG1412L Datasheet and Product Info | Analog Devices

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>