UniFlame UFPDL1307BLK Glass Fireplace Doors Installation Guide

UFPDL1307BLK Glass Fireplace Doors
Installation Guide

WARNING
DO NOT close the glass doors until the fireplace has completely cooled.

INSTALLATION GUIDELINES

• This glass door unit is designed to overlap and cover the front of your fireplace opening and only covers a certain range of fireplace sizes.
  To ensure you have purchased the correct door unit for your fireplace, see the chart below: SIZE| OVERALL DOOR DIMENSIONS| FITS FIREPLACE OPENING
  ---|---|---
  | Width x Height| Width| Height
  Small| 37.5″ x 30″| 30″ – 37″| 22.5″ – 29.5″
  Medium| 37.5″ x 33″| 30″ – 37″| 25.5″ – 32.5″

*Height includes a 2″ riser bar (not assembled). See assembly instructions for details.

• This glass door unit is only intended for brick and mortar (masonry) fireplaces. Do not install this unit on a prefabricated (metal) fireplace.
• Be sure to check with your local municipality for any regional ordinances or codes before installing this unit.

PACKAGE CONTENTS / HARDWARE

**** SAFETY INFORMATION

Before installing your fireplace doors, besure to readall safety and assembly information to ensure the proper operation of the unit. If you have any questions regarding the proper use of this product, be sure to contact our customer service department, whose contact information is found in our warranty.
WARNINGS

• DO NOT close the glass doors until the fireplace has completely cooled.
• DO NOT close the glass doors while a fire is burning in the fireplace. Even though the doors are made of tempered glass, the glass can still shatter if exposed to excessive heat.
• DO NOT leave the screen doors open while the fire is burning. Be sure to leave the screen doors closed while a fire is burning in the fireplace. This will prevent sparks from escaping from the fireplace.
• DO NOT allow any cold liquid or substance to come in contact with the glass doors while they are hot. This could cause the glass to shatter.
• DO NOT build a fire that is too large or place the firewood grate too close to the screen doors to avoid discoloration of the frame.
• DO adjust the damper found at the bottom front of the screen doors to allow for proper air flow into your fire.

**WARNING:** This product can expose you to chemicals, including lead and lead components which are known to the State of California to cause cancer, birth defects, and other reproductive harm. Wash your hands after handling this product. For more information go to www.P65Warnings.ca.gov.

FIREPLACE PRECAUTIONS

• Before operating a new fireplace, be sure to neutralize the fireplace by applying a diluted solution of ammonia, followed by a warm then cold rinse.
• Never store combustible or volatile substances inside the fireplace.
• Keep all combustible and volatile substances away from the front of the fireplace.
• Do not use any combustible or volatile substances to help start a fire.
• Open the chimney damper before starting a fire.
• Keep children and pets away from the fireplace while in use.
• Do not touch any part of the glass door unit with your bare hands while a fire is burning. Always use an insulated glove to open and close the doors and damper.
• Never use your fireplace as an incinerator.
• Always allow ashes to fully bum out and cool before disposing.

PREPARATION

Before beginning assembly of product, make sure all parts are present.
Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble the product.
Package Removal: Carefully remove the glass door unit and all other pieces from the box, placing the glass door unit face down on a soft flat surface.
Tools Required for Assembly (not included): Flathead Screwdriver, Phillips Head Screwdriver, Work Gloves, Measuring Tape, Scissors
INSTALLATION VIDEO
Scan QR code below for assembly video.

https://youtu.be/85k2hXIyuig

INSTALLATION INSTRUCTIONS

DETERMINING IF THE RISER BAR IS NEEDED

• You may or may not need to install the riser bar, depending on the height of your fireplace.
• To determine if you need the riser bar, place the glass door unit in front of your fireplace to see if it fits your fireplace opening.
• If the top of the glass door unit does not reach the top of your fireplace opening, you can install the Riser Bar to the bottom of the unit to add extra height to the unit.

1. RISER BAR INSTALLATION
To attach the riser bar:

• Lay the unit face down onset flat surface.

• Attach the Riser Bar (M) to the bottom of the unit by inserting the Long Machine Screws (G) through the holes in the Riser Bar and the holes on the bottom of the
  unit, as shown.

• Secure the Long Machine Screws using the Hex Nuts (H), as shown.

Hardware Used
G Long Machine Screws (x2)
H Hex Nuts (x2)

2. INSERTING THE INSULATION

• Be sure to wear work gloves while handling the insulation strips.
• Trim insulation strips to fit with scissors.
• Lay the unit face down on a soft flat surface.
• Insert the Wide (L) and Narrow (K) Strips of Fiberglass Insulation into the wide and narrow gaps on the back of the unit, including the Riser Bar.

3. LOCATING THE LINTEL BAR

• The lintel bar is the L-shaped metal bar that runs along the top of the inside opening of your fireplace, holding the bricks in place.

5. ASSEMBLING THE BRACKETS
Before attaching the unit to your lintel bar, you have to assemble the brackets.

• You will use either the Long T-Brackets (A) or the Short T-Brackets (B) to attach the unit to your fireplace, depending on the width of your lintel bar.
• Use a measuring tape to measure the width of your lintel bar, measuring from the back of the lintel bar to the front of your fireplace.
• Use the width measurement of your lintel bar to determine whether you will need the Long T-Brackets or the Short T-Brackets.
• Assemble the 2 T-Brackets (long or short) to the 2 Lintel Clamps (C), using the Short Machine Screws (J).
• Do not over-tighten the machine screws yet. Leave them loose. You will tighten them later when you adjust the width of the clamp.
• Insert the Short Thumb Screws (F) into the back of the Lintel Clamps, as shown.

NOTE: You can assemble the T-Brackets to the Lintel Clamps either face-up or face-down (as shown), depending on the height of your fireplace. Try it face-up first. If the clamps do not fit your fireplace properly, you can always go back and re-assemble them face-down.
Hardware Used

A Long T-Brackets (x2)|
---|---
B Short T-Brackets (x2)|
C Lintel Clamps (x2)|
J Short Machine Screws (x2) 411|
F Short Thumb Screws (x2)|

6. INSERTING THE ASSEMBLED BRACKETS INTO YOUR DOOR UNIT
Now that the brackets are assembled, you are ready to attach the door unit to your lintel bar. (Recommendation:
This part of the installation might require 2 people – one person to hold the unit in place, while the other person clamps the unit to the fireplace.)

• Insert the “T” of each T-Bracket into the slots found on the back of the door unit. Insert each “T” vertically into the slot, and then turn it until it’s horizontal. The assembled T-Brackets/Lintel Clamps should now be hanging loosely in the slots.

7A. ATTACHING THE UNIT TO YOUR LINTEL BAR

• Open both the glass doors and the screen doors on the unit.
• With the doors open, place the unit against the front of your fireplace opening. (This is where you may  need assistance holding the unit in place while you clamp it to the lintel bar.)
• With the unit in place, reach inside the fireplace   and position the T-Bracket/Lintel Clamp over the lintel bar.
• Adjust the width of the T-Bracket/Lintel Clamp until it is snugly grasping the lintel bar and tighten the Small Machine Screw.
• With the T-Bracket/Lintel Clamp fitting snugly over  the lintel bar, tighten the thumb screw until the unit is held firmly in place.
• With both thumb screws securely tightened, the unit is now firmly attached to the top of your fireplace.

7B. ALTERNATE ATTACHMENT METHOD FOR THE TOP OF THE DOORS ONLY
If the attachment Brackets and Lintel Clamps do not attach to your fireplace, use this alternate attachment method.
Additional Tools Required: Electric Drill, 7/32” High Speed Steel Bit, Pencil and Safety Glasses
(RECOMMENDATION: This part of the installation might require 2 people – one person to hold the unit in place, while the other person measures and attaches the unit to the fireplace.)

• Select a T-Bracket that will sit flush with your lintel bar: Long T-Brackets (A) or Short T-Brackets (B).
• Attach the selected T-Bracket to the door. Place the glass doors against the fireplace opening and center.
• Use your pencil and mark through the T- Bracket, on the lintel. Mark both sides.
• Remove the glass doors and drill a 7/32″ hole into the lintel bar at each marked location.
• Place the glass doors against the fireplace opening and line up the brackets to the holes in the lintel bar.
• Use the Thread Cutting Screw (I) to attach both T-Brackets to the lintel bar.

Hardware Used
A Long T-Brackets (x2)
B Short T-Brackets (x2)
I Thread Cutting Screws (x2)

8. SECURING THE BOTTOM OF THE UNIT TO THE WALL

•  Insert the 2 Long Thumbscrews (E) into the 2 Pressure Brackets (D), as shown.
• Insert the Pressure Brackets into the holes found on the bottom of the back of the door unit. Choose the holes that will best fit the size of your fireplace.
• Tighten the Long Thumbscrew’s” until the point of each thumbscrew is digging into the brick on the side of your fireplace.
• If the thumbscrews do not reach the brick or are too long, you can reposition the Pressure Brackets by inserting them into a different set of holes on the unit.

 Your glass door unit is now securely attached to your fireplace!

Hardware Used
D Pressure Brackets (x2)
E Long Thumbscrews (x2)

9. GLASS DOOR ADJUSTMENT
Note: some models do not have these hinge styles and therefore this step can be skipped.
The glass doors are attached to your unit with 4 hinges (2 hinges on each door). Each hinge is attached to the frame of the unit with 2 adjustable screws. If the glass doors are not aligned properly, they can be easily adjusted:

• Loosen the 2 screws on one of the hinges.
  DO NOT remove the screws —just loosen them.

• Adjust the position of the door.

• Once the door is positioned properly, re-tighten the screws.

• If necessary, loosen the other hinge, adjust the door, and re-tighten.

CARE AND MAINTENANCE

WARNING: DO NOT allow any cold liquid or substance to come in contact with the glass doors while they are hot. This could cause the glass to shatter.
GLASS:

• Allow glass to cool fully before cleaning.
• Clean the glass with a diluted solution of ammonia and a clean cloth.
• DO NOT use scouring pads or harsh chemicals as it may damage the tempered glass.

FRAME:

• Clean the surface of the unit with a damp cloth.
• If necessary, use a diluted solution of alcohol to remove fingerprints or other markings.
• DO NOT clean with scouring pads, harsh chemicals, cleaners, or solvents.

WARNING
DO NOT close the glass doors until the fireplace has completely cooled.

WARRANTY

We warrant to the original retail purchaser of this product, and to no other person, that if this product is assembled, maintained, and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such product shall be free from defects in material and workmanship. We may require reasonable proof of your date of purchase. Therefore, you should retain your sales slip or invoice. This Limited Warranty shall be limited to replacement parts, which prove defective under normal use and service and which we shall determine in its reasonable discretion upon examination to be defective. Before returning any parts, you should contact our customer service department using the contact information listed on the cover of this manual. If we confirm, after examination, a defect covered by this Limited Warranty in any returned part, and if we approve the claim, we will replace such defective part without charge. If you return defective parts, transportation charges must be prepaid by you. We will return replacement parts to the original retail purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance or service by you or any third party, or failure to perform normal and routine maintenance on the product as set out in this owner’s manual. In addition, the Limited Warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase.
This Limited Warranty is in lieu of all other expressed warranties. We disclaim all warranties for products that are purchased from sellers other than authorized retailers or distributors, including the warranty of merchantability or the warranty of fitness for a particular purpose. WE ALSO DISCLAIM ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. WE SHALL HAVE NO LIABILITY TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. We further disclaim any implied or express warranty of, and assumes no responsibility for, defects in workmanship caused by third parties.
This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to everyone.
We do not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment, and no such representations are binding on us. This warranty gives you specific legal rights, and you may also have the other rights that vary from state to state. As some states do not allow exclusions or limitations on an implied warranty, the above exclusions and limitations may not apply.

KEEP THIS MANUAL FOR FUTURE REFERENCE
Model No. ___
Size ____
Finish ___
Dimensions ___
This information can be found on the carton label.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at: 1-888-398-8643, 8 a.m. – 8 p.m., EST, Monday – Sunday. You can
also contact us at registration@mrbarbq.com or visit MrBarBQProducts.com.

References

• Mr. Bar-B-Q Products LLC – Everything for the Grill
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>