LUMENE Eden Extra Bright 200C User Manual

June 3, 2024
LUMENE

User manual

Eden Extra Bright 200C

Thank you for choosing Lumene products. Please read the manual carefully before installation and use. And put it away for future use.
– Please tear out all the blue tape from the trap door before powering on.
– Please take out the EVA Pad from the fabric rod when the screen goes up.
– Please take out the EPE foam When the support arm goes up.
– Please do not reach into the casing gap to prevent hands injury when the screen goes up.
– Please put the screen in place with no wind to prevent it from falling over.
– Please Do not disassemble or replace the original spare parts at will.
– If there is any fault, don’t hesitate to get in touch with the after-sales service department.
– Any functional or structural adjustment will not be further notified and subject to practical product.

PARTS

SCREEN STRUCTURE DIAGRAM

SCREEN INSTALLATION GUIDELINES

A.

  1. Measure the size of the screen, calculate the installation position of the screen;
  2. Mark the installation line at the bottom of the casing. Take the adjustable mounting brackets, with a symmetrical spacing of 1600 mm of the center line.
  3. Stick a flat marking line on the top to mark the positions of the four screw holes.

B.

  1. Drill the holes and drive the expansion tube.
  2. Place the adjustable mounting brackets vertically, align the screw holes, and tighten the ø5*40 selftapping screws.

C.
Keep the power supply side to the left, gently place the screen on the bracket, align the bottom rivet nut with the hole on the bracket, and screw on the M5X14 combination screw, adjust and fix the screen left and right to a suitable position, and tighten the screws to fix the screen.
D.
Connect the power supply and fully unfold the fabric; observe the angle between the fabric surface and the wall, and use the hexagonal wrench to rotate the hexagonal adjustment screws on the two mounting brackets; after fine-tuning the inclination of of the screen.

Remove the 4 screws to remove the B mounting plate (This mounting plate can be selected according to the specific installation method).

Note: Installation methods 12, B mounting plate is not used and can be removed. Installation method 34 First, fix the B mounting plate on the screen shell with M5x14 combination screws, and then put the fabric lightly on the A mounting plate and then lock the connecting screws between the A and B plates.

FUNCTIONS AND INSTRUCTIONS

This product has three control methods
A. Manual cycle button
B. 12V trigger control
C. RF remote control
A.Manual cycle button
The manual cycle button is set on the end cover of the power supply side of the shell. Pressing the button will control the screen to rise, stop, fall, stop, and rise repeatedly. Continuously loop.
b.12V trigger control with a 12V trigger cable; the screen synchronizes the opening and closing of the projector (that is, when the projector is turned on, the screen is automatically turned on; when the projector is turned off, the screen is automatically turned off)

C. RF remote control
– Press the up button, the decorative door opens first, and the fabric rises;
– Press the stop button, the decorative door or fabric will paus
– Press the down button, the fabric rolls back, and the decorative door is closed.
– Jog the up key and down key, the fabric moves up or down;
Usually used in electronic stroke positioning settings. Intelligent electronic itinerary positioning (this product can realize the screen unfolding itinerary setting through the remote control).
Operation method (stretch a paperclip into the hole, press the positioning setting button on the back of the remote control): Screen unfolding stroke setting:
positioning setting key (lighted) -> remote control up and down to the desired position -> stop -> positioning setting key (light off) -> location record successful -> positioning setting key (light off) -> location record successful

DECORATIVE DOOR ANTI-PINCH FUNCTION

The decorative door of this product is equipped with a flexible door opening and closing device, which can protect hands or objects from accidentally extending into the screen when closing the door.
Abnormal situation: If the elastic protection device is triggered when the door is closed, the tension spring may be stretched, and the opening and closing angle of the door will change, making it impossible to reset.
Solution: Remove the two Ø4 x 8 self-tapping screws connecting the door, turn the tension spring counterclockwise to the correct rebound, and restore the parts to the original state.

FABRIC CLEANING

Ultra-short throw anti-light screen cleaning : (Do not use a rag to wipe!)
– Using soft brush(in parts box), lightly brush horizontally along the texture of the screen to remove the dust or fine particles on it.
– For light-colored smudges that do not affect the projection, no need to deal with them; if it affects the viewing effect, it can be removed with a sticky tape without residue.
Ordinary regular throw fabric cleaning method
Use clean water or mild detergent to gently wipe the stains on the surface of the fabric(do not use corrosive detergents), and then retract the fabric after air-drying or absorbing moisture

ELECTRICAL PARAMETERS

Voltages & Frequencies: 110V/60Hz or 220V/50Hz (Actual voltage shall be subject to the electrical label shown on the product)
Wireless remote control (F): Voltage 3V, using battery CR2032X2, transmitting frequency; 868MHz, effective control distance is about 15 meters.
Troubleshooting

  1. When the product leaves the factory, the tab tension on both sides of the screen have been adjusted to a suitable elastic length. If in the process of use, the two sides of the fabric are too loose or too tight, you can refer to the following methods to adjust.

IF the tab tension is too loose:
insert the adjustment key into the adjustment hole, press andhold the adjustment key and turn clockwise,and the cable is tightened.
IF the tab tension is too tight:
insert the adjustment key into the adjustment hole, press and hold the adjustment key and turn it counterclockwise, the line is loosened.

IF the tab tension is too loose:
insert the adjustment key into the adjustment hole, press andhold the adjustment key and turn clockwise,and the cable is tightened.
IF the tab tension is too tight:
insert the adjustment key into the adjustment hole, press and hold the adjustment key and turn it counterclockwise, the line is loosened.

Important operating considerations
Setting up is very easy but has to be done carefully to ensure its durability.
Before first use, always position your screen horizontally on a stable and flat surface.

Warning:
– Don’t hang or put anything on the top of the screen case when your screen when your screen is unrolled.
– Don’t put your finger inside the case when you retract the screen fabric back to the case.
– Dust and scratches will lower the image of projection quality. Please pay particular attention to the following points:
a. Do not touch the screen surface with your hand.
b. Do not draw on the screen surface.
c. Do not cruff or scratch the screen with hard sharp items subject to cause damage.
d. Never use chemicals to clean the screen surface.
– Make sure there is nothing on the screen before you retract it into the case.
– To remove dust on the cloth, use a dry and soft-haired brush and rub it delicately.
– Close the screen to protect the cloth.

LIMITED WARRANTY :
All LUMENE produds carry a two-year limited warranty period when purchased from LUMENE, a LUMENE distributor or a LUMENE authorized retailer. This warranty covers all defects in materials and workmanship in the product manufactured by LUMENE.
Warranty limitation and exclusions:
This warranty covers only the products purchased from LUMENE or a LUMENE authorized retailer or distributor and runs for a two-year period from the date of the purchase by the first end-user. Except in the following cases, this warranty covers ony material or manufacturing deffect. This limited warranty is subject to the following exceptions:
– the serial number has been removed, modified or made illegible.
– the defects or damage result from use of the products in a manner that is not normal or customary; improper operation or misuse; accident or neglect such as dropping the products onto hard surfaces; contact with water, rain, extreme humidity; contact with sand, dirt or the like; or contact with extreme heat, or spills of food or liquid.
– physical damage to the surface of the product, induding scratches, cracks or other damage.
– non respect of the instructions supplied with the product.
– damage due to the shipment of the product (claims have to be addressed to the carrier).
– someone other than LUMENE or its authorized service centers attempts to maintain, alter, modify or service the product in any way.
– any other damage due to the Iack of technical knowledge or experience of the user without any link with deffects of the product.
Any of these voids the warranty.

To be eligible for limited warranty coverage:
The limited warranty applies only to the first end-user. Any person exercising a claim under this limited warranty must show the proof of the date of purchase, such as the sales receipt or invoice, and that the product was purchased new.
The warranty is strictly limited to the country of the original purchase.
Warranty related expenses:
LUMENE will take charge of all the expenses on parts and labor related to the repair or the replacement of the products. The expenses related to the shipping and insurance fees will be shared as described below.
To obtain warranty service:
During the warranty period, to exercise the limited warranty, the purchaser must first contact:

  1. the original place of purchase,
  2. the LUMENE local distributor,
  3. LUMENE.

The warranty service for this device is limited to the country of original purchase.
You will receive instructions on how to ship the product to the nearest designated LUMENE authorized Service Center. The product must also be packed in its original packaging or a similar package insuring an equal degree of protection. You must ship it with freight, duties and insurance prepaid.
Regardless of where you are instructed to return the product, you must always include:
a) a copy of your invoice, bill of sale or other comparable proof of purchase.
b) a written description of the problem.
c) the name and location of the place of purchase and, most importantly.
d) your address and telephone number.
Always retain your original proof of purchase. Do not send any product back to a service center before prior agreement. Upon receipt of the product, LUMENE or its authorized service center will check the product and will ship you a repaired or replacement product, freight and insurance expenses prepaid. If additional information is required, please contact your retailer or the LUMENE local distributor.
Limitation of liability:
Except where these dispositions are inapplicable or unlawed to state laws or other jurisdiction rights: For any defective product, LUMENE sole liability is to repair or replace the product. By no means no event shall LUMENE be liable, whether in contract or tort (including negligence) for damages in excess of the purchase price of the product, or for any indirect, incidental, special or consequential damage of any kind or to any other products, or loss of revenue or profits, loss of business, or other financial loss arising out of or in connection with the ability or inability to use the product, to the full extent these damages may be disclaimed by law. Any litigation, which cannot be regulated by way of preliminary conciliation and relating to the interpretation or the execultion of this Warranty and the obligations herein contained will be distinct definitively, according to the rules of conciliation and arbitration of the International Chamber of Commerce of Paris, France, by one or more referees named in accordance with its rules. The applicable law will be the French one.

Update : 31/08/2022www.lumene-screens.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals