Radial SB-48 Power Bar User Guide
- June 3, 2024
- Radial
Table of Contents
True to the Music
SB-48
POWERBAR
USER GUIDE
INTRODUCTION
Thank you and congratulations on your purchase of the Radial StageBug SB-48
dual phantom power supply. We have purposely written this manual to be short,
as most users will likely be familiar with the use of phantom power. We do
suggest that you take a moment to read through this document to familiarize
yourself with the features that are built into the SB-48. For more detailed
information, please visit the FAQ section on the Radial website. This is where
we post questions and answers that come from users after the product is
released. If you do not fi nd an answer, we invite you to send us an email at
info@radialeng.com and we will do our best to
answer your query in short order.
The StageBug SB-48 is a two channel phantom power supply designed to provide
condenser microphones and active direct boxes with 12 or 48 volts of regulated
power. The SB-48 can supply one or two phantom powered devices and allows
their use with audio systems that do not supply phantom power on their own.
The SB-48 features XLR inputs and outputs wired to the AES standard, an LED
power indicator and comes complete with power supply. An integrated lock-down
clamp for the power supply cable protects against accidental disconnection. To
address speciality microphones that require 12 volts, a recessed ‘set &
forget’ switch reduces the voltage output.
FEATURES
- XLR-F INPUTS: Used to connect the mic signal to the StageBug SB-48. Phantom power is generated inside the SB-48 and injected into the mic capsule via the F-XLR connectors and mic cable.
- POWER INPUT AND LED: The power jack accepts Radial’s 15VDC/400mA power adapter. The LED illuminates when the power supply is connected and the SB-48 is active.
- CABLE CLAMP : Used to lock down the power supply cable and prevent accidental disconnection.
- XLR-M OUTPUTS: Used to connect the mic signal to the mixing console or preamp. Equipped to block other sources of phantom power and prevent over-powering your condenser mic or active direct box.
- +12/48V SWITCH: Used to change the phantom supply from the standard +48 volts to +12 volts for speciality microphones.
- FULL-BOTTOM NO-SLIP PAD: This provides electrical isolation and plenty of ‘stay-put’ friction to keep the SB-48 in one place.
CONNECTION
Before connecting the StageBug SB-48 make sure the sound system is turned off
and all levels are set to zero. Do not connect the power supply until all
connections to and from the SB-48 have been made. This will avoid loud
transients that could cause damage to equipment downstream such as
loudspeakers and tweeters. After use, remember to turn off the PA system
before you disconnect the SB-48’s power supply and the mic lines.
Using balanced XLR mic cables, connect the output of a condenser microphone or
active direct box to the XLR-F input. Next, connect the XLR-M output to your
mixing console or mic preamp. Connect the second channel following the same
steps.
CONNECT THE POWER
After the audio connections are made you can connect the included 15V/400mA AC/DC power adapter to the SB-48’s power jack. The power LED illuminates when the SB-48 is active. Turn your audio system on and test the mic signals at a low volume to ensure the system is properly connected and the microphones are working.
USING THE CABLE CLAMP
A handy cable clamp located next to the power jack can be employed to prevent accidental power disconnection. Use a hex driver to loosen the cable clamp’s screw a few turns until the cable can be looped through the clamp and re- tighten.
USING THE 12/48V SWITCH
You can set the phantom power voltage to 12 volts using the recessed 48/12V
switch on the side of the SB-48. Use a small screwdriver to access the switch.
When the switch is in the outward position the SB-48 will supply 48 volts of
phantom power. When set to the inward position it will supply the mic with 12
volts.
Stagebug SB-48 SPECIFICATIONS
| Circuit type: | Non-radiating phantom power supply |
|---|---|
| Number of channels: | 2 |
| XLR connectors: | AES standard pin-1 Ground, pin-2 (+), pin-3 (-) |
| Phantom output: | Switchable +48 / +12 volts DC |
| Power supply: | 15VDC / 400mA external supply included |
RADIAL ENGINEERING 3 YEAR TRANSFERABLE LIMITED WARRANTY
RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free from defects in material and workmanship and will remedy any such defects free of charge according to the terms of this warranty. Radial will repair or replace (at its option) any defective component(s) of this product (excluding fi nish and wear and tear on components under normal use) for a period of three (3) years from the original date of purchase. In the event that a particular product is no longer available, Radial reserves the right to replace the product with a similar product of equal or greater value. In the unlikely event that a defect is uncovered, please call 604-942-1001 or email service@radialeng.com to obtain an RA number (Return Authorization number) before the 3 year warranty period expires. The product must be returned prepaid in the original shipping container (or equivalent) to Radial or to an authorized Radial repair center and you must assume the risk of loss or damage. A copy of the original invoice showing date of purchase and the dealer name must accompany any request for work to be performed under this limited and transferable warranty. This warranty shall not apply if the product has been damaged due to abuse, misuse, misapplication, accident or as a result of service or modifi cation by any other than an authorized Radial repair center.
THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND
DESCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
ARTICULAR PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED
ABOVE OF THREE YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE OF
THIS
PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU LIVE AND WHERE THE PRODUCT
WAS PURCHASED.
Radial Engineering Ltd.
1845 Kingsway Ave., Port Coquitlam, BC V3C 1S9,Canada
tel: 604-942-1001
• fax: 604-942-1010
info@radialeng.com
Made in Canada
StageBug SB48.” User Guide – Part# R870 1221 00
© Copyright 2013 all rights reserved Specifications and appearance are subject
to change without notice.
www.radialeng.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>