SLIGER S620 Tower Air Coolers Instruction Manual
- June 3, 2024
- SLIGER
Table of Contents
SLIGER S620 Tower Air Coolers
SCREWS
The S620 comes with a total of 6 different screws. For the purposes of this
guide, we will assign a unique color to each screw to signify their location
in this guide.
EASY-OFF PANELS
The front, side panels, top, and bottom all have toolless removal via their ball-stud mounting points. Be careful, panels may be very tight on the first few times on/off.
RE-ASSEMBLY NOTES
Side panels are reversible to either side. Front Panel can be installed with
either end at the top or bottom.
Power Button Location
The S620 has two power button locations allowing you to choose what
orientation the case is. Either with the GPU on the bottom of the case or the
GPU on the top of the case. Here is the process for removing the power button
switch panel and installing it in the other location.
-
Step 1
Remove 2x 6/32 x 1/4″ FLAT HEAD -
Step 2
Remove the Power button/ USB panel. -
Step 3
Flip the chassis over and reinsert 2x 6/32 x 1/4″ FLAT HEAD to secure the Power button/USB panel.
MOTHERBOARD
Be sure to install your IO shield first!
Some CPU coolers and AIOs may require a back plate to be installed before
installing the motherboard into the case. Once the IO shield is properly
installed the motherboard can now be mounted using 4x 6-32 x 1/4” HEX HEAD
screws. A Phillips #2 screwdriver with a minimum 3” shaft length is
recommended for installing these screws.
SSD MOUNTING
The S620 has two SDD mounting locations on the SFX PSU length-wise and width-
wise bracket. On the length-wise bracket, one SSD attaches with 2x M3 x 6mm
PAN HEAD screw and the other attaches with 2x M3 x 5mm FLAT HEAD. Be sure to
install drives with the SATA power and data connections facing the same
direction as PSU power connections.
The S620 has two SDD mounting locations on the SFX PSU length-wise and width-
wise bracket. For the Width-wise bracket, each SSD attaches with 2x M3 x 6mm
PAN HEAD screws. Be sure to install drives with the SATA power and data
connections facing the same direction as PSU power connections.
POWER SUPPLY INSTALLATION
- The SFX PSU attaches to the bracket with 3x 6-32 x 1/4” HEX HEAD screws.
- Install the power pig-tail by snaking it through the rear chassis hole and securing it with 2x M3 x 8mm FLAT HEAD screws. Then insert into the SFX PSU.
- Lastly, the SFX PSU mounting bracket is secured to the case spine via 2x 6-32 x 1/4” FLAT HEAD screws. These screws are located at the top middle of the spine, next to the motherboard corner standoff. There are also 2x 6-32 x 1/4” FLAT HEAD screw locations behind the front panel of the case.
WIDTH-WISE PSU INSTALLATION
The SFX PSU attaches to the width-wise bracket with 6x 6-32 x 1/4” HEX HEAD
screws.
Then SFX PSU mounting bracket is secured to the case spine via 4x 6-32 x 1/4” FLAT HEAD screws as shown in the photo.
NOTE:
The width-wise bracket can be installed in either orientation shown to allow
for different AIO/Fan configurations described throughout the
manual.
POWER CORD
STANDARD MOUNT
The power cord should be installed by pulling it in from the rear through the
power cord mount hole, passing through the cable mounting bracket. The inlet
and metal plate are then mounted via 2x M3x5mm FLAT HEAD screws as shown.
PIGTAIL MOUNT
The cord should be installed by pulling it in from the rear through the power
cord mount hole. With the cable partially out of the case the cable grommet
should be clipped on to the power cord, and then clipped into the metal plate.
The metal plate can then be mounted via 2x M3x5mm FLAT HEAD screws.
PCIe CARD
The PCIe card is secured with up to 3x M3 x 6mm PAN HEAD screws.
NOTE:
Depending on your GPU card size. You may have to try different angles and
approaches to get it in the chassis and seated into the PCIe slot. Do this
before installing CPU Heatsink or CPU water cooling block.
120/240/280mm AIO INSTALLATION
The S620 supports a variety of water-cooling / AIO setups. The three different
configurations are; a 120mm AIO installed on the PSU Bracket, 240mm or a 280mm
radiator attached to the side bracket.
The 120mm radiator can be mounted to the PSU bracket as shown in the image below. Using 4x 6-32 x 1/4” HEX HEAD screws to secure it to the bracket. Hoses must come out of the radiator facing the open side of the case as shown.
NOTE:
For the 120mm AIO, You MUST attach the radiator first before installing your
SFX PSU.
240/280mm AIO INSTALLATION CONT.
The S620 side bracket supports either a 240mm or 280mm radiator. Fans are
recommended to be mounted on the inside exhausting air out the side panel
through the radiator.
NOTE:
For the 280mm radiator, it is best to set the radiator inside the case after
getting the water block secured to the CPU, and then placing the side bracket
over the radiator. Secure the radiator to the side bracket with 4x to 8x 6-32
x 1/4” HEX HEAD screws (See next page). Lastly, the side bracket is attached
to the chassis with 4x 6-32 x 1/4” FLAT HEAD screws.
280mm radiator fitment NOTE: it is a very snug fit.
FANS installation
SIDE BRACKET FANS
The S620 side bracket can fit 2x 120mm or 140mm fans.
BOTTOM FANS
Fitment Guide:
- 2- Slot to 2.7-Slot GPU’s can fit – 140mm, 120mm x 25mm, 120mm x 15mm slim fans.
- 3- Slot GPU may fit 120mm x 15mm slim fans. Check clearance.
- Full 3-Slot GPU can NOT fit any size fan.
TOP MOUNTED FANS
The S620 can fit 2x 120mm slim 15mm fans mounted on the top of the chassis.
NOTE: The case handle bracket can not be used with this
configuration.
FRONT FAN
The S620 supports up to 140mm by 25mm,
NOTE: Fan can only when used in conjunction with the “width-wise” PSU
bracket.
MOTHERBOARD SIDE FAN
The S620 supports up to 120mm by 25mm on the motherboard side of the chassis
NOTE:
Fan can only when used in conjunction with the “width-wise” PSU Bracket and
without any SSDs mounted.
REAR FAN
The S620 supports 120mm fan mounted on the rear of the chassis. Use standard
KB5 screws to attach the fan. NOTE: KB5 screws not included.
SSD MOUNTING
The S620 has an optional SSD window bracket. Each SSD attaches to the bracket with 2x M3 x 6mm PAN HEAD screws. The assembly then attaches to the chassis with 2x 6-32 x 1/4” FLAT HEAD screws.
NOTE:
When using the SSD Window Bracket, You CAN NOT use the side bracket for fans
or radiator, but you can pair the SSD window bracket with a 120mm
AIO.
CASE HANDLE BRACKET
The S610 case handle bracket can be mounted in two different locations shown in the photos below. They are attached to the chassis with 4x 6-32 x 1/4” FLAT HEAD screws.
- GPU Bottom Orientation
- GPU Top Orientation
- NOTE: A 120mm by 15mm thick fan can be mounted to the case handle bracket.
Use 4x KB5 screws to attach the fan to the bracket. Note: KB5 screws are not included.
CASE HANDLE
The case Handle is attached with a 2x M4 x 12mm Socket Cap Use the included Allen key to tighten it.
NOTE: Do not over-torque screws as it will marr paint on the top panel.
AIR-COOLING CONFIGURATIONS
Documents / Resources
|
SLIGER S620 Tower Air
Coolers
[pdf] Instruction Manual
S620 Tower Air Coolers, S620, Tower Air Coolers, Air Coolers, Coolers
---|---