Hisense L9G Laser TV Display Screen Installation Guide

Hisense L9G Laser TV Display Screen Installation

SAFETY PREVENTION AND PRECAUTION

WARNING:
Please follow the instructions strictly, or it may cause serious injury or even death.
NOTE:
Please follow the instructions strictly, or it may cause injury and product damage.

• We recommend that two people load, unload and transfer this screen.
• The product should be installed by professional and technical personnel, and by following the installation guide. Installing the product by unqualified personnel is dangerous and may cause personal injury.
• The product should be installed at the place that can support its weight. Otherwise, the product may fall and cause personal injury.
• After installation, if you want to move or replace the product, please contact manufacturer’s professional and technical personnel. Unqualified personnel may cause safety problems.
• Do not hit the product, or it may fall and cause injuries.
• Keep little children away from the screen.
• Please strictly follow the installation guide when installing the product. Otherwise, it may cause serious injuries or damage the product.
• Two or more people are needed when installing the product and adjust the height of the product. If you install it by yourself, the product may fall, cause personal injury, or damage the product.
• Before installation, make sure to check if the wall is strong enough to support the product. And remember to use accessories and screws provided with the product. Otherwise, safety problems may happen.
• When drilling holes on the wall, make sure to use drilling machine and drill bit of designated size. Follow the instructions on drilling depth. Otherwise, safety problems may happen.
• Please clean and maintain the screen with soft cloth carefully. If there is no dry cloth, cloth dipped in a little water can be used, but the water temperature should be lower than 40 ·c Do not use alcohol or organic solvents, and do not use acid or alkali solvents.
• DO NOT scratch the screen with hard or sharp objects.
• Keep the screen away from direct sunlight.
• Control the heat and humidity of the room.
• Do not install lighting tube within 3m of the screen.
• The illumination angle of the light should not be perpendicular to the screen.

PREPARATION

Required Tools to Install the Screen

Hardware and Parts List for Screen Mounts

Check the Type of Wall You Have

• Minimum wood stud size: common 51 x 102 mm nominal 38 x 89 mm
• Minimum metal stud size: common 51 x 102 mm nominal 38 x 89 mm
• Minimum solid concrete thickness: 203 mm Minimum concrete block size: 203 x 203 x 406 mm

Prepare Your Space

• Width  2.25m
• Height  1.8m from the installation surface to the ceiling.
• For the optimal viewing experience, we recommend a minimum viewing distance of 3m from the screen.

Recommended size for your TV stand
We recommend that you place your Laser TV on a TV stand that is at about 50cm tall and wide enough to hold the TV.
F100W/LTS100MHEU/DLT100-A matches Laser TV 100L9G/100L9

F100W/L TS100MHEU/DL T100-A matches Laser TV 100L5F/100L5G/100L5* NOTE:** The tolerance of H is within ±1 Smm.

Connect the wands as shown in the illustration below.

 Install the Wall Mount Brackets

NOTE: Make sure you have your paper template, pencil, tape and screwdriver.

1. Starting from the top of your TV stand, add 1.501 m above it to get the height of the top of the paper template. Mark the height onto the wall. H and L 1 may change according to the adjustment of Laser TV, the length and height is only for reference.

2. Put the paper template on the center of the wall.
   NOTE: The paper template should match the mark you made on the wall.

3. Make sure the paper template is level.

IF YOU HAVE A DRYWALL WITH WOOD STUDS/ METAL STUDS
NOTE: Make sure you have your stud finder.

• Use a stud finder to find the studs in the areas on the paper template, and mark the center of the studs with a pencil. Following the vertical line on the paper template, mark where the bottom screws should be within the proposed area.
• On the marks, drill the holes for the four screws.
• Remove the paper template and install the brackets with the screws. Firmly tighten the screws.
  NOTE: Hold the bracket in place when tightening the screw to keep the bracket from shifting.

IF YOU HAVE A SOLID CONCRETE OR CONCRETE BLOCK WALL
NOTE: Make sure you have your concrete anchors and hammer.

• Drill holes for the top screws. Following the vertical line on the paper template, drill holes for the bottom screws within the proposed area.
• Remove the paper template and insert four anchors into the holes.
• Be sure the anchors are flush with the concrete surface.
• Install the brackets with the screws and firmly tighten them.
  NOTE: Hold bracket in place when tightening the screw to keep the bracket from shifting.

CAUTION: All screws MUST BE firmly tightened to prevent unwanted movement of the brackets. Make sure the brackets are securely fastened to the wall before continuing on to the next step.

• Attach the upper and lower parts of the wall bracket wands with the screws and bolts. Make sure the two parts are aligned and firmly tighten the screws.
• Hang the wands on to the wall-mount brackets .

HANG THE SCREEN

1. We strongly recommend that two people handle this screen when moving it. Be sure to use gloves(included) to protect the screen from grease, sweat and dirt.

2. Check the up and down direction of the screen. To make sure the orientation of the screen is correct, check the ‘UP’ label on the back cover of the screen. When your Laser TV is placed on a flat surface(figure a), the screen should be installed in its normal direction and the arrow of ‘UP’ label points up(figure b). When your Laser TV is mounted upside down(figure c), the screen should be installed inverted, the arrow of ‘UP’ label points down(figure d). Please see the illustrations below.

3. Split the release paper on one side of the velcro strips. Paste the velcro strips on the left and right side of the bottom of the screen(on the back side of the screen).

4. Place the screen onto the brackets.
   NOTE: We do not recommend mounting the TV to the ceiling. However if you choose to, then the orientation of the screen will need to be reversed.

5.  Make sure the screen is horizontally and vertically level. To prevent the bracket wands from keeping the screen from being vertically level, fold and rest them on the screen bracket on the bottom of the screen (see the diagram).

6. When finishing adjusting the positon of screen, split the release paper on the other side of the two velcro strips. Remove the foam support and push the screen to the wall.

Adjust the Height of the Screen
Attach the handles of the wands on the wall-mount brackets and adjust the height of the screen. Refer to the top border to match the screen to the display image.
WARNING:
Do not look directly at the lens when this device is on because the laser light may damage your eyes!

• If the screen is higher than the image, then rotate the wands clockwise and move the screen down.
• If the screen is lower than the image, then rotate the wands counterclockwise and move the screen up.

After you’ve completed adjusting the screen height, remove the handles. Fold and rest the wands on the screen bracket on the bottom of the screen.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>