ST Engineering AETHON IO NUC Assembly User Manual
- June 3, 2024
- ST Engineering
Table of Contents
ST Engineering AETHON IO NUC Assembly
Product Description
The IO NUC Assembly is the next iteration of our SOM platform. This assembly has been specially designed to function across our family of robots.
Specifications
- Dimensions: 18.895”L x 14.237”W x 2.493”H (47.99 cm L x 36.162 cm W x 6.332 cm H)
- Operating Weight: 10.0 lbs(5.536 kg)
- Communications: Wi-Fi
- Environmental: Interior use
Label Requirement
For OEM integration only – device cannot be sold to general public. The FCC / ISED certification label of a module shall be clearly visible at all times when installed in the host product; otherwise, the host product must be labeled to display the FCC / ISED certification number for the module, preceded by the word “contains” or similar wording expressing the same meaning, as follows:
- Contains FCC ID: 2AA6CSOMRPL20
- Contains IC: 11082A-SOMRPL20
- Contains FCC ID: PD98265NGU
- Contains IC: 1000M-8265NG
Approvals and Standards Compliance
- FCC, Part 15, IC, CE
- EN 12100:2010, EN 60204-1:2006+A1:2009, IEC 60034-1:2004-04
- EN 61000-6-4:2007; EN 61000-6-2:2005; EN 60601-1-2:2007, EN 55022
- EN 301 489-1, EN 301 489-17
- FCC CFR 47, Part 15; ICES-001; Australian RCM Compliance
- ETSI EN 300 220+1 V2.4.1 & ETSI EN 300 220-2 V2.4.1
- EN 300 328 1.7.1, EN 301 893 1.6.1
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC
Warning: Changes or modifications to the robot, charging dock, or any
related equipment not expressly approved by Aethon could void the user’s
authority to operate the equipment. This equipment has been tested and found
to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference,
in which case the user will be required to correct the interference at his own
expense.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RSS GEN
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter IC: 11082A-SOMRPL20 has been approved by Innovation,
Science and Economic
Development Canada to operate with the antenna types listed below, with the
maximum permissible gain indicated. Antenna types not included in this list
that have a gain greater than the maximum gain indicated for any type listed
are strictly prohibited for use with this device.
- 418/433Mhz
- Linx: ANT-418-CW-RH-SMA: Maximum gain -6.7dBi
- Tagoglas: TI.10.0111: Maximum gain 0dbi
- 2.4/5GHz
- World Products: WPANT30220-S1A: (2.4GHz +2.8 dBi) (5GHz +0.2 dBi)
© Copyright Aethon , Inc. 2022. All Rights Reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>