ABIS Express Automatic Electric Hand Dryer User Manual

: June 3, 2024
: ABIS

Table of Contents

Technical Parameters:
Note before installation:
Components Name:
Installation Method:
Test Operation:
Maintenance:
Terms of Guarantee:
Step-by-Step Installation Guide:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Express Automatic Electric Hand Dryer
User Manual

Technical Parameters:

Rated Voltage| AC 220 – 240V
AC 110 – 127V| Waterproof Grade| IPX1
---|---|---|---
Rated Frequency| 50/60 HZ| Sensing Distance| 12 ± 3 cm
Rated Power| 2300W| Air Speed| 20 m/s
Temperature Controller Cut-out Temperature| 115°C| Drying Time| 10-15S
Thermal Fuse| 121°C| Overall Size| 245 x 265 x 207 mm

Note before installation:

Warning

Warning: do not use the hand dryer near water, in places such as bathtubs, showers, basins, or other containers with water.
Children should be supervised to ensure they do not play with the device. The hand dryer is intended to be used indoors only.
Professional installation is highly recommended to install power lines to avoid electric shock hazards.
Ensure the device is unplugged before installation.
Ensure you install an earth leakage circuit breaker to prevent shock and ﬁre hazards.
Do not unassemble, repair or alter the hand dryer on your own to avoid the risk of an electric shock, ﬁre, and other accidents.

Attention

Before installation, ensure there are no other objects around 400mm. Do not install the hand dryer on the stainless steel or artiﬁcial marble surface to avoid misoperation.
The hand dryer unit should be ﬁrmly ﬁxed to the even surface (wall).
Do not install the hand dryer near corrosive or ﬂammable gases or objects. It may cause ﬁre or product damage and malfunction.
Do not install the hand dryer in an environment with high temperature or dust, as it may cause product damage.

Components Name:

ABIS Express Automatic Electric Hand Dryer - Figure 1

Installation Method:

ABIS Express Automatic Electric Hand Dryer - Figure 2

Drill 4 holes in the wall.
Screw the two ﬁxing screws oﬀ the cover with the hexagonal wrench and remove the panel. Detach sensor connecting wire.
Using the screws, ﬁx the machine on the wall & connect it to electric power. ( Please Note: We recommend the installation to be done by a professional electrician only).
Put the cover on the machine and cover it using the hexagon wrench.
Plug the hand dryer in power.

Test Operation:

After installation, please test the hand dryer operation according to the steps below:

The hand dryer should be in standby mode after the power has been switched on.
The hand dryer should automatically stop after 60 seconds of work.

Usage:

After washing hands, place hands under air outlet around 10 cm away. The hand dryer will be automatically activated using the automatic sensor. Please retreat the hands when hands are dried, and it will stop working in 2 seconds.
After 60 seconds of continuous usage, the hand dryer will stop automatically.
Do not dry any clothes or handkerchiefs, etc.
Do not pull the electric cord abruptly to avoid any short circuits.
Do not use the hand dryer for extremely long hours. The wind outlet might get extremely hot and damage the sensor.

Tips:

If the hand dryer sensor is not working or turning on automatically, please adjust the sensor distance trimmer. The trimmer is indicated in Picture 1.
The closer you place your hands to the hand dryer, the faster they dry.
Be careful of the surface heating when in use continuously.

Maintenance:

Ensure the device is unplugged before cleaning. Clean the shell with a natural detergent when dirty.
Do NOT use alkalescent, lacquer thinner, abrasive detergents, or detergents containing acid.
Do NOT use friction tools, such as nylon brushes to avoid shell scratching.
When cleaning the shell, avoid the water drops inside the hand dryer to prevent electric shock or short circuit.
To extend the service life, it is recommended to unplug the device when it is not in use.
In case of the device break down, immediately unplug it from the power and contact the professional electrician for repair.
If the hand dryer is not in use for a long time period, unplug it from the power supply, and store it in a box inside a dry and clean space after cleaning.

Terms of Guarantee:

The product warranty period is one year from the purchase date.
During the warranty period, in case of a warranty case, the device can be replaced for free. The original invoice and the quality insurance card stamped by the dealer will need to be presented by the customer.
The following are NOT in the scope of free maintenance:
a. Improper use and fault caused by demolition, unassembling, and repair by a technical specialist without ABIS authorization.
b. Faults caused by ﬁres, earthquakes, thunder, and other natural disasters.
c. Abnormal voltage
d. Faults caused by non-matching power.
e. Faults caused by long-time operation in unacceptable working conditions.
f. Warranty card and insurance card ﬁlled out incorrectly or not explicitly.
After the 1-year warranty period, the maintenance of the product is no longer free, while our company remains committed to service.