Akyga AK-PD-05 Shaver Charger User Manual

: June 3, 2024
: akyga

Table of Contents

Akyga AK-PD-05 Shaver Charger
Short description of the product
What is in the box
Symbols explanation
Safety Precautions
Removing the most common problems
Preparing the Power Supply for Use
Technical specification
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Akyga AK-PD-05 Shaver Charger

Short description of the product

The Akyga AK-PD-05 charger is used to deliver power to Philips shavers with direct current. The 5.4 W power supply is compatible with all 15 V/360 models. Aset of protectors OVP, OTP, OPP, SCP, OCP and the soft start technology provides safe and stable work of both power supply and powered device. The product is adapted to supply voltage in the range of 100-240V, 50/60Hz. The power consumption of powering notebook can not exceed the power supply nominal current. The product is compatible with the applicable national and European requirements.

What is in the box

AK-PD-05 power supply

Symbols explanation

There is a particular danger connected with service.
There is a risk of losing health or life (e.g. by electic shock).
Important tips and information
The II protection class device. It provides protection against electric shock against direct and indirect contact, and thanks to the additional isolation it is not necessary to connect the device case with the protective earth conductor.
The device is intended only for domestic use, indoors.

Safety Precautions

WARNING! The product heats up during operation. To reduce the risk of burns or overheating the power supply, do not place it in a restricted ventilation area. Also, do not allow the working power supply to touch soft surfaces such as pillows, blankets or clothing. The power supply meets the limits on the surface temperatures available to the user, as defined in the International Standard for Safety of Information Technology Equipment (IEC 60950).
A connecting device whose demanded power is greater than power of the power supply can cause device failure or even damage (burn) of the power supply.
An electrostatic discharge occurs when two objects touch each other, for example, an electric charge that occurs when the user touch a metal door handle after walking on a carpet. Discharging electrostatic charges from fingers or other electrostatic conductors can damage electronic components. To avoid damaging the device, abstain from touching electrical outlets, wires and electonic circuits. The user’s contact with electronic components should be kept to a minimum.

The manufacturer of the product is not responsible for damage or insults caused in effect of disobey the safety instructions and information contained in this user manual.

Keep the product and the packaging out of range of children and animals. The package includes a foil that child could choke while playing.
It is forbidden to apply the mechanical load to the product – strong shocks, impacts, dropping or crushing may cause its damage.
Product operation in adverse conditions is not allowed. Adverse conditions are primarily: exposure to direct sunlight, high or very low ambient temperatures, strong vibrations, high humidity, surrounding of gases, dusts or flammable and aggressive liquids.
If the product has been damaged, does not work properly or has been stored for a long period of time in bad or unfavorable conditions, safe operation of the device is not possible. It is essential to stop using the product and to protect it against re-use for security purposes.
Product and power cord should not be touched with moist or wet hands under no circumstances.
Short-circuiting the current connection is prohibited.
Make sure that the power cord is not crushed, bent, twisted, rubbed against sharp edges or mechanically loaded in any other way. Avoid the thermal load of the cable – in particular, keep away from heat sources (such as stoves, radiators, and fireplaces).
Power cords should be laid in such a way as to eliminate the risk of stumbling or hooking over.
Its forbidden to modify the power cord. In the case of modifications, the cable may be damaged, causing threats to life, health, and property.
Connection of the power supply to electricity is done by connecting cable with the CEE 7/16 to a grounded electrical outlet.
Before connecting the adapter to the mains socket, make sure that the voltage specified on the power supply matches voltage supplied to the household socket.
Mains plug should be disconnect from power socket if the product is not in use for a long time.
When disconnecting the power cord from the socket and from the device, do not pull on the cord, but only on the part of the cable plug provided for this purpose.
In case of any doubts regarding operation, safety or connection of the product, please contact the manufacturer or a qualified specialist for this purpose.
All maintenance, adjustment and repair work on the product may only be carried out by a qualified person in a specialist facility.

Removing the most common problems

Problem	Cause	Solution
The device connected to an electrical outlet via power supply does not work
No mains voltage	Ÿ Check the correct connection of the power supply to the

mains socket

Ÿ Check the mains fuses

The power supply is overloaded| Ÿ Disconnect the power supply from the device, check the correctness of the current parameters
There is a suspicion of a product defect| Ÿ Stop using and contact the seller
The power supply does not correspond to the current parameters| Ÿ Disconnect the power supply from device and check if current parameters are correct

Ÿ Contact with seller