K V ELEKTRO 48001 Compressor Set User Manual
- June 3, 2024
- K V ELEKTRO
Table of Contents
K V ELEKTRO 48001 Compressor Set
General Warnings
When using air-powered accessories, always wear safety clothes. Keep the work area free and always maintain in a stable position. Do not allow inexpert persons to use tools withous suitable supervision. Keep children and animals at a distance from the work area. Improper use of compressed air may cause serious injuries.
Washing Spray Gun
- Technical data: Maximum pressure 12 bar.
- Instruction for use: Fill the bowl (1), screw it to the body of the gun (2), and then connect the air hose to the inlet fitting (3). Press lever (4) to spray the liquid. Adjust the size of the jet required using the ring nut (5) (A-B). Warning: Always hold the gun horizontally during use in order to improve the suction of the liquid in the bowl. Do not spray harmful substances without wearing a mask and safety goggles.
Inflation Gun
- Technical data: Maximal pressure:12 bar.
- Instruction for use: Connect the air hose to the inflet fitting (1) on the gun. To inflate the tire and check the pressure, insert the fitting (2) in the valve of the tire holding down the lever (3) on this; following insertion, release the lever (3). With the gauge facing you, read the pressure; for inflation, press the lever (4) fully for few seconds and then release it; repeat the operation until zou have obtained the pressure required as shown bz the needle on the dial of the gauge. For deflation, release the lever (4) and press the button (5) with your thumb until all the air has been expelled. (C-D) Warning: Never exceed the inflation pressure recommended in the instruction for use of the objec to be inflated. Protect the gauge against impacts. In the case of impacts, check calibration.
Blowing Gun
- Technical data: Maximum pressure: 12bar
- Instruction for use: Connect the air hose to the inflet fitting (1) on the gun. Direct the nozzle towards the area or bject to be blown and press the lever (2). The flow of air can be adjusted by regulating pressure on the lever (2).
Air Brush for Painting
- Technical data: Recommended operating pressure: 4/5 bar
- Instruction for use: Airbrush with gravity bowl (4.1): Screw the bowl (1) to the body of the gun (3). Fill the bowl with paint (1) and close it with the lid (4). Make sure that the vent valve (5) is open. Airbrush with lowe bowl (4.2): Screw the bowl (10) to the body of the gun (3) and secure tightly with a wrench. Fill the bowl (11) with paint and fit it on the cover (10); fasten with a quarter turn to the right. Conncet the air hose to the inflet fitting (6) on the gun and adjust the pressure (4/5 bar) from the compressor. Use the rear ring-nut (7) to adjust the amount of paint to be sprayed (tighten if you are using more fluid paints, open in the case of thicker paints) and the side ringnut (8) to regulate the size of the jet. (E-F /G-H). Direct the front perforated head of the nozzle (2) so that it is perpendiculat to the direction of the painting. Prior to effective use, practise on a test material until you have obtained optiomal adjustment and effect. Never leave paint inside the bowl in order to use this subsenquently as this may cause irreparable damage to the precision parts of the air brush. After use, always clean the inside the air brush thoroughly, filling the bowel with pure solvent and spraying this without polluting the enviroment (spray on a rag or absorbing surface) until is no trace of the paint used in the jet of the solvent sprayed. Clean the external parts of the gun stained by the paint used with a rag dipped in solvent. For more thorough cleaning, completely unscrerw the rear ring-nut (7) and, taking care not to lose the internal spring, remove the needle of the nozzle; the loosen the front ring (9) and remove the perforated head of the nozzle (2) and unscrew the nozzle with a wrenchů put all the components in a container with pure solvent for number of hours; dry the components carefully and then carry out the above procedure in reverse order in order to reassemble all the parts.
Warning: Do not use the paint gun in a closed enviroment without ventilation. Do not use the air brush without wearing a safety mask.
Spiral Cord
- Technical data: Max pressure: 12bar
- Instructions for use of cord with fast disconnects: Connect the end of the cord fitted with connector (1) to the compressor; connect the orhet end fitted with connector (2) to the air powered tool. To insert the connector (2) in the tool, push until it clicks in place. To detach the cord, gasp the tool firmly with one hand and the ring-nut of the connector (2) with the other and pull in the opposite direction. If this operation is difficult, make sure that you ahve vented all the air from cord. (I-L)
- Intructions for use of cord with bayonet fitting: To connect the cord to the tool, insert the fitting of the cord (2) in the ring-nut on the tool and draw up tightly. To detach to cord, loosen the ring-nut on the tool and slide out the fitting; if this operation is difficult, make sure that zou have vented all the air from the cord. (M-N).
Warning: Before connecting or disconnecting a tool of the cord, make sure that you ahve switched off the compresor. The cord must not be crushed or bent as it could be pierced.
Read User Manual Online (PDF format)
Loading......