Hansa LED Magic Plus LED Lamp Instruction Manual
- June 3, 2024
- HANSA
Table of Contents
LED Magic Plus LED Lamp
Instruction Manual
LED Magic Plus LED Lamp
Check to be sure
- Check that the delivery is complete and that the light does not exhibit any trans- port damages.
- If the delivery is incomplete or exhibits transport damages, do not use the light. Contact your vendor, where you puchased the light.
Proper use
This light is only suitable for lighting dry indoor areas (home/office).
Before you use the light
Before you use the device, please first carefully read through the safety
notes and operating instructions.
Keep all safety notes and instructions for future use. Pass on all safety
notes and instructions to any subsequent user of the light.
For your safety
Signal words
WARNING
Failure to observe the warning may result in injury to life and limb.
CAUTION
Indicates a hazard with a low risk that could result in a minor or moderate
physical injury.
Symbols
| Only suitable for indoor spaces!
---|---
| Do not use any sprays when cleaning!
| Double insulation
| The light is suitable for installation on surfaces with normal flammability.
Safety notes
WARNING
Hazardous grid voltage! Risk of electric shock!
Deficient electrical installation or excessive mains voltage may result in an
electric shock.
- Do not use the light if it exhibits visible damages.
- Check the device and cable for damages on a regular basis.
- Have repairs performed by a qualified workshop.
- For repairs, only parts may be used that correspond to the original device specifications. There are electrical and mechanical parts in this unit which are essential in order to avoid exposure to sources of danger.
- Immerse neither the light nor the mains cord or plug in water.
- Never take hold of the mains cord with wet hands.
- Keep the light, mains plug, and mains cord away from open flames, and hot surfaces.
- Never attempt to grasp an electric appliance once it has fallen in water. In such a case, immediately disconnect the mains plug.
- If you are not using the light, cleaning it or in the event of a malfunction, turn the light off and always pull the plug out of the socket.
- Never pull the mains cord out of the socket by the cord, instead always take hold of the mains plug.
- Never use the connector cord as a carrying strap.
- If the mains cord of this device is damaged, it must be replaced by the manufacturer or its customer service department or a person with similar qualifications in order to avoid risks.
- Render the device, which has outlived its purpose, unusable. Pull the mains cord out of the socket and cut the mains cord in half.
WARNING
Danger to children and other persons!
Children often do not recognise the risks of handling electric appliances or
underestimate them. Children can become trapped in the packing film when
playing and suffocate.
– Do not allow children to play with the packing film and never allow them to
use electric appliances without supervision.
CAUTION
Fire hazard!
Do not use any sprays or the like to clean the light.
– Do not cover the light head with cloths or the like. The heat radiated from
the light could cause them to catch fire.
The operating device is located in the power supply unit.
Notes on the place of installation
- Set up the light on a solid, level surface (e. g. table or sideboard) close to a socket.
- Make sure that there is no risk of it tipping and that the cord does not pose a trip hazard.
Assembly
Turning the light on/off
- Insert the plug in a socket.
- Arrange the light in the desired position.
- Touch the button to switch the lamp on/off.
Wireless charging
- To be able to charge your device using the wireless charger, your device must be compatible with inductive charging technology (Qi standard). Please read the operating instructions of your device.
- Note that mobile phone cases, covers or other materials between the wireless charger and the back of your device may interfere, slow down or even prevent charging.
- Ensure that there are no metal parts on the back of your device. Metal may heat up significantly in the field of the induction charger, causing damage to your device and/or the charger.
- Devices get warm during charging. They will cool down after they are fully charged. The charger and devices suitable for inductive charging are protected against overheating.
- The required charging time may vary depending on the device’s battery capacity, the charge level, the age of the battery or the ambient temperature.
- Even if the light of the lamp is switched off, the device can be charged via the wireless charger.
1. For wireless charging, place the device to be charged on top of the icon
on the base. The device must be placed directly over the icon on the base for
the charging function to work.
Lighting source
- Lighting source service life: 30 000 hours
- The lighting source cannot be replaced.
- The construction of the luminaire does not allow the lighting source to be replaced, as there is a risk of damaging the luminaire.
Care and cleaning
WARNING
Hazardous grid voltage! Risk of electric shock!
Improper use could result in electric shock.
- When cleaning the light, always pull the mains plug out of the socket. When doing so, always take hold of the plug and not the cord.
- Make sure that no water penetrates the inside of the light or other parts carrying a current.
- Carefully wipe off the light with a damp cloth or a dry dust cloth.
Technical data
| Voltage: | 100 – 240 V AC/50 – 60 Hz |
|---|---|
| USB charger: | 5 V 2.1 A |
| Wireless charger: | 5 V 1 A |
| Power: | 10 W |
| Luminous flux: | 500 lm |
| Colour temperature: | 3000 K/4500 K/6000 K |
| Protection class: | II |
| Model number: | 41-5010.716 |
This product contains a light source of energy efficiency class E.
Distribution
styro GmbH
Industriestrasse 2
D-91583 Schillingsfürst
Tel. +49 9868 98949-0
www.styro.de
styro ag
Frauholzstrasse 27
CH-6422 Steinen
Tel. +41 (0)41 833 80 10
www.styro.ch
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>