INHO MAURETZ Lucellino and DOPPIO ambient Instruction Manual
- June 3, 2024
- INHO MAURETZ
Table of Contents
Lucellino nt & DOPPIO
ambient Instructions
Lucellinont ambient & DOPPIO
ambient Ingo Maurer 1992 / 2022
Instructions for assembly
Please read these instructions carefully before going any further, and keep
them in a safe place for future reference
The lamp assembly and all electrical work must be carried out by a
professional electrician.
Caution: Lucellino ambient is not suitable for use in damp areas or
outdoor areas. The wings can be impregnated with ordinary hairspray or hair
lacquer.
Important: Lucellino ambient requires a 12V power supply. Never connect
the LED bulb directly to the mains supply (230/125 volts)!
Preparations for assembly
Caution: Switch off or remove the fuse for the mains supply to the wall
or ceiling outlet before beginning the assembly.
Undo the Allen screw on the brass bolt (1), pull out the brass wire (2) and
remove the white cover (3). ① Undo the two screws (4) on the lid and open the
outlet box (5). Use the box as a template to mark the two drill holes. ②
Caution: Take care to ascertain the exact layout of the wiring in the
wall or ceiling, so as to avoid drilling into a power cable.
Assembly
Drill the two 6 mm-diameter holes and insert the S6 plugs. Attach the outlet box (5) with the screws (6) provided and tighten the screws, as shown in fig. ② Remove about 8 cm from the outer covering of the power cable (7) and strip 5 mm from the ends of the phase and neutral leads. Connect the phase and neutral leads to the contacts in the terminal (8). Replace the lid of the wall box, fasten the two screws (4) and fit the white cover (3). ② Push the brass wire (2) into the bolt (1) until it reaches the stop, and position it as desired. Tighten the Allen screw on the brass bolt. ①
Inserting the bulb
Carefully wrap the soldered red wire from the led bulb and smooth it down.
Pass it through the socket ring (10) and screw the bulb in. Match the red
wire, with a loose coil or
two, to the routing of the brass wire and insert the end (9) into the contact
socket (11) on the cover plate as far as it will go. ③
Changing the bulb
Caution: Switch off or remove the fuse for mains supply and allow the
lamp to cool down completely!
Important: Lucellino ambient requires a 12-volt AC power supply. The LED light
bulb must not be used in any 24 volts halogen version of Birds or Lucellino!
Before unscrewing the spent bulb, pull the red wire (9) out of the contact
sleeve (11) and unwind it from the brass wire. Then follow the procedure
described above in the
section headed „Inserting the bulb“.
Cleaning
The goose-feather wings can be cleaned carefully with a soft paintbrush. A mild household cleaning fluid may be used for the cover and cable.
Technical specification
230 V~50 Hz; 125 V~60 Hz. The correct voltage and frequency for your lamp are
indicated on the type label. Secondary
12 Volt AC. LED 5 W, Doppio: 2x 5W, 380 lm (Φuse-360°), 2000-2700 K CRI>90,
E27 socket,
Electronic transformer; It is possible to connect a universal
dimmer for LEDs (with low or adjustable minimum load).
According to the manufacturer, the LED has an average life of 20000 hours.
The lamp comes with light source of the energy class G (A-G).
This bulb is manufactured exclusively for Ingo Maurer GmbH. Replacements are
only available from our webshop or authorized retailers.
**** A defective lamp, transformer or LED bulb must be disposed as electronic
scrap. It must not get into domestic waste.
Any repairs that may become necessary must be carried out by a qualified
electrician.
The legal and contractual warranty for defects and product liability will be
void, should the installation instructions not be duly followed or non-
original components be employed.
Ingo Maurer GmbH Kaiserstrasse 47
D-80801 München
Tel. +49. 89. 381 606-0
Fax +49. 89. 381 606 20
info@ingo-maurer.com
www.ingo-maurer.com
März 2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>