topvehicletech GRKVW02 Volkswagen Installation Guide
- June 3, 2024
- topvehicletech
Table of Contents
****
topvehicletech GRKVW02 Volkswagen
ABOUT
THIS PRODUCT
The GRKVW02 installation kit allows the retention of the vehicle’s steering
wheel controls and helps to maintain the original aesthetic of the interior
when installing a new car stereo. The GRKVW02 gives you everything you need
for a complete install in one box. The components of this kit are compatible
for the following vehicles with RCD200/RCD300/RCD310/RCD500/RCD510 factory
stereos:
Amarok (2H) 2009 – 2016 EOS (1F) 2006 – 2015 Golf (MK5/6) 2003 – 2013 Jetta
2005 – 2015 Passat (B6/B7) 2005 – 2015 Polo (9N/9N3/6R) 2009 – 2014 Scirocco
2008 – 2015 Touran 2006 – 2015 Tiguan (5N) 2007 – 2015 Transporter 2009 – 2015
The wiring harness and interface will retain the steering wheel controls and
factory phone buttons (if vehicle is equipped). The interface supplied
features a Quadlock connector.
CONTENTS
- 1x Fascia plate (with accessories)
- 1x Instruction manual
- 1x Steering wheel control harness and interface
- 1x Antenna adapter
- 1x Stereo patch lead
CUSTOMER SUPPORT
Installations should be carried out by, or under the guidance of an experienced installer. If you do encounter any problems during the installation of this product, then please contact our dedicated customer service team at: Phone: 01420 470 605 E-Mail: help@topvehicletech.com
FITTING GUIDE
STEREO REMOVAL
-
a. Use a panel removal tool to release the air cone unit and remove 2x screws located here (this step is only required for Volkswagen Golf vehicles).
1b. Use a panel removal tool to remove the trim surrounding the main radio. This will reveal 4x screws which will need to be removed. -
Once free, pull the head unit out of the dashboard and disconnect all of the wiring in the process.
FASCIA PLATE SET-UP
- Attach the brackets to the new stereo. These brackets allow you to set the specific depth of the unit in relation to the fascia plate. Start by lining up the spacers (Fig 1.)on the inside of the plates
- Attach the spacer and plate combination to the corresponding side of the stereo using the screws that come with the stereo. Test this set up outside of the dashboard by sliding into the radio cage.
- Take the fascia in hand, and place it atop the caged radio combination. If the depth/alignment of the stereo hangs out too much/is reccessed to far, use the radio removal keys to release the stereo from the cage and repeat the process.
- When you’re happy with the bracket alignment, you can proceed to install the fascia into the dashboard, utilizing the pre-existing screws.
STEREO INSTALLATION
-
Take the steering wheel control interface and attach the 14-way steering wheel harness connector to the relevant side.
-
Take the patch lead and only attach ‘Key 1’, ‘Key 2’ and ‘Ground’ to the corresponding wires on the stereo. When done, connect the 12-way connector to the steering wheel control interface.
-
Attach the antenna adapter to the vehicles pre-existing connection and the back of new stereo.
-
Attach the additional wiring on the harness to the back of the stereo:
Pink – Speed Pulse Green – Park Brake Purple – Reverse -
When all the above wires (and any additional accessories) have been connected, finally make the power connections between the stereo and the vehicles pre-existing connector.
STEERING WHEEL CONTROL FUNCTIONALITY
Please note: configuration layout may differ dependent on vehicle model.
Version 1
Original
Button
- Volume +
- Volume –
- Track –
- Track +
- Mute
- Pick Up
New Function
- Volume +
- Volume –
- Track –
- Track +
- Mute
- Pick Up (Short Press) Hang Up (Long Press)
Version 2
Original
Button
- Volume +
- Volume –
- Star
- Pick Up
- OK
- Track +
- Track –
New Function
- Volume +
- Volume –
- Mute
- Pick Up (Short Press) Hang Up (Long Press)
- Source
- Track +
- Track –
WIRING DIAGRAM
TECHNICAL ASSISTANCE
If at any point you experience any problems and need any assistance before,
during or after the installation process, please contact us via :
Phone: 01420 470 605
E-Mail: help@topvehicletech.com
Mon – Fri 9am – 5.30pm GMT
If you would like to download a digital copy of this manual, or any other
product, then please visit the
www.topvehicletech.com website. This manual
is considered correct at the time of printing but is subject to change. For
the latest manuals & updates, refer to our website.
Copyright 2021 by TopVehicleTech.
All rights reserved. No part of this publication may be reproduced,
distributed or transmitted in any form or by any means, including
photocopying, recording, copying or other electronic or mechanical methods,
without the prior written permission of the author.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>