Martview TS1100 Intelligent Lead Free Soldering Station Instruction Manual
- September 28, 2024
- Martview
Table of Contents
TS1100 Intelligent Lead Free Soldering Station
“`html
Product Information
Specifications
-
Product Name: TS1100 Intelligent Lead Free Soldering
Station -
Designed for lead-free soldering
-
Equipped with 3-wires grounding plug
-
Temperature control for efficient heat transfer
Product Usage Instructions
Safety Instructions
WARNING: Misuse may potentially cause death or
serious injury. Please comply with precautions.
CAUTION: Mishandling can cause injury or
damage. Follow safety guidelines.
NOTE: Important procedures or points are
highlighted.
Tips for Safe Usage
- Avoid touching metallic parts near the tip
- Do not use near flammable items
- Turn off power when replacing parts or installing tips
- Use only with rated voltage and frequency
- Do not use if damaged, especially the supply cord
Tip Care and Maintenance
-
Select a tip maximizing contact area for efficient heat
transfer -
Choose a tip that allows good access to the solder joint
-
Shorter tips for precise control, longer tips for densely
populated boards
Error Messages
-
S – E Sensor error: Check sensor circuit if
displayed, power may be cut off -
H – E Heater error: Indicates a possible
heater malfunction if power can’t be sent to the soldering
iron -
ERR handle error: Check hand shank type or
handle presence
Frequently Asked Questions (FAQ)
Q: What should I do if the display shows an error message?
A: Refer to the error code explanation in the
manual and take appropriate action based on the displayed
message.
Q: How do I calibrate the temperature settings?
A: Follow the calibration steps provided in the
manual to ensure accurate temperature control.
“`
TS1100 Intelligent Lead Free Soldering Station
Operation Manual
Thank you for purchasing an Intelligent Lead Free Soldering Station. It is
designed for lead free soldering. Please read this manual before operating the
unit. Store this manual in a safe, easily accessible place for future
reference.
. Safety Instruction
WARNING
In this instruction manual, “Warning” “Caution” and “Note” are defined as
follows:
WARNING: Misuse may potentially cause death of, or serious injury to the user.
CAUTION: Misuse may potentially cause injury to the user or physical damage to
the objects involved. For your own safety, be sure to comply with these
precautions.
NOTE: A Note indicates a procedure or point that is important to the process
being described.
CAUTION
When the power is on, the tip’s temperature is very high. The mishandling may
lead to burns or fire, be sure to comply with the following precautions:
Please avoid an abuse of the unit and use the appliance only as the described
manner. Do not touch the metallic parts near the tip. Do not use the product
near flammable items. Advise other people in the work area that the unit can
reach a very high
temperature and should be considered potentially dangerous. While replace
parts or install tips, turn the power off and allow the unit to cool
to room temperature.
To prevent damage to the unit and ensure a safe working environment, be sure
to comply with the following precautions: Appliance shall only be used with
rated voltage and frequency. (Refer to the
trademark back of equipment.)
Page1
Don’t use the appliance if it is damaged, especially the supply cord. This
machine is equipped with a 3-wires grounding plug and must be plugged
into a 3-terminal grounded socket. Do not modify plug or use an ungrounded
power socket. If an extension cord is necessary, use only a 3-wire extension
cord that provides grounding. Do not use the unit for other applications
except soldering. Do not rap soldering iron against the work bench to shake
off residual solder, otherwise the iron will be damaged by shocks. Do not
modify the unit by yourselves. Only use genuine replacement parts. Do not wet
the unit. When your hands are wet, don’t use and disconnect the unit, or to
pull the supply cord. The soldering process will produce smoke, so make sure
the area is well ventilated. While using the unit, don’t do anything which may
cause bodily harm or physical damage. Children don’t recognize the danger of
electrical appliances. Therefore use or keep the appliance only under
supervision of adults and out of the reach from children.
. Tip Care and Maintenance Select a Correct Tip
1. Select a tip that maximizes contact area between the tip and solder joint.
Maximizing contact area gives the most efficient heat transfer, allowing
operators to produce high quality solder joints quickly.
2. Select a tip that allows good access to the solder joint. Shorter tip
lengths allow more precise control. Longer or angled may be needed for
soldering densely populated boards.
.Error messages
Various error messages will be displayed when there is something wrong with
the unit.
S – E Sensor error:
If there is a failure in the sensor or anywhere in the sensor circuit, “S-E”
will be displayed and power to the soldering iron will be cut off.
H – E Heater error: If power can’t be sent to soldering iron, the display
window will show “H-E”. This indicates the possibility of a heater
malfunction.
ERR handle error: the type of hand shank is wrong, or have no handle.
Page2
Page11
3. press “+” or “–” key select value, he 100’s digit in the screen is
flashing. Press “+” or “-” button to select value. after selecting, press
“ENTER” button.
4. press “+” or “–” key select value, he 10’s digit in the screen is
flashing. Press “+” or “-” button to select value. after selecting, press
“ENTER” button.
5. press “+” or “–” key select value, he 10’s digit in the screen is
flashing. Press “+” or “-” button to select value. after selecting, press
“ENTER” button, return main interface.
6. If the temperature still has departure, you can repeat calibration in
accordance with above steps.
We recommend using the 191/192 thermometer for measuring the tip temperature.
If the soldering station is locked by password, it will not be able to
calibrate the tip temperature and you must input the right password.
Up and Down Limit of Temperature
1 The unit cannot set upper and bottom limit of temperature value, procedure
tolerant up and down limit of temperature is 20,when tip’s temperature is out
of this range, it can give an alarm.temperature flicker
. Summary
The soldering station’s temperature adopts LCD double temperature display and
digital calibration, shortcut and convenience. The temperature induction is
very exact and sensitive, the speed of heating and recovery of temperature is
very fast, and so it is the one of the most perfect tools for lead free
soldering.
. Feature
1. password lock function, protecting technological parameter. 2. temperature
warning function, Celsius and Fahrenheit can exchange. 3. hand shake is very
light and handy, can distinguish hand shake. 4. LCD, heater can be pull out
easy, maintenance is simple. 5. anti-static device, ESD measuring ability.
Page10
Page3
. Specifications
Type
Temperature displaying type Power consumption
Working voltage
Temperature Range Temperature Stability Ambient Temperature(Max) Tip to Ground
Resistance Tip to Ground Potential Dimension (W×H×D)
TS1100 LCD 70W 220VAC 100~450/212F~842F ±2(stationary air, no load) 40 2mV 2 11315092 mm
4. Setting & Operating the Soldering Station
CAUTION: Before operation, please check whether the voltage accords with the
rated voltage on the unit’s nameplate.
4.1 Iron Holder and Sponge
CAUTION: The sponge is compressed. It will swell when moistened with water.
Before using the unit, moisten the sponge with the water and squeeze it dry.
Failure to do so may result in damage to the soldering tip. If the sponge
becomes dry during working, add appropriate water.
1. Dampen the small cleaning sponge with water and then squeeze it dry. 2.
Place it in groove of the iron holder base. 3. Add a little water to iron
holder. The small sponge will absorb water to keep
the large sponge around it wet at all times. 4. Dampen the large cleaning
sponge and place it on the iron holder base.
Page4
0-99min. as following
1. F degree
2. ESD OFF 3. Password
4 SLEEP TIME
0 picture 5-6
5.2.5 exit menu
Press “-” key, select the fourth menu, press “ENTER” key exit setting menu,
return main menu.
Calibrating the Temperature
The soldering iron should be recalibrated after changing the iron. The unit
adopts digital calibration mode and the revision value is inputted by pressing
button, make the adjustment easily.
Calibrate by using thermometer:
1.Set the unit’s temperature to a certain value. 2.When the temperature
stabilizes, measure the tip’s temperature with thermometer and write down the
reading.
Page9
5.2.2 ESD function
Press “-” key, select the second item, ESD setting: press “ENTER” affirm,
press “+” key or “-” key selecting, ON is opening ESD function, OFF is closing
ESD function, and then press “ENTER” affirm.
5.2.3 Resetting password
Press “-” key, select the third item, resetting password: press “ENTER”
affirm, show , import new password, press “ENTER”, import new password again,
The changing of password is successful until the latest two passwords are the
same.
4.2 Connection
CAUTION: Be sure to turn off the power switch before connecting or
disconnecting the soldering iron. Failure to do so may damage the soldering
station. 1. Connect the connector of the handle cord to the socket behind the
unit. Take notice of inserting position about connector. 2. Place the
soldering iron at the iron holder. 3. Insert the power plug into grounded
power socket. 4. Turn on the power switch.
4.3 turn on/shut down
1. turn on: turn on the power switch which in the back of the main unit,enter
into main interface.
Interface display as follow:
5.2.4 Off time setting
- Press “-” key, select the fourth item, off time setting, press “ENTER”
affirm, then press “+”or “-“key to change the off time. The range of off time
is from
Page8
2. shut down: long press POWER key about 3 second shut down the unit, or
press power switch which in the back of main unit.
Page5
4.4 Setting the Temperature
CAUTION: Make sure the temperature of the unit can be adjusted (password is
correct or the password is initial 000). When setting temperature, the heating
element is on. Operation as following steps:
Temperature rising:
Press “+” button directly. If so, the setting temperature will raise 1 and the
display window will display the set temperature. When loosen the “+” button,
the display window will delay to display the set temperature about 2seconds.
If within 2seconds, press the “+” button again, the setting temperature will
raise 1 again. If press the “+” button and not loose at least 1second, the
setting temperature will rise rapidly. Till the needed temperature reaches,
then loose the “+” button.
Temperature dropping:
Press “-” button directly. If so, the setting temperature will drop 1 and the
display window will display the set temperature. When loose the “-” button,
the display window will delay to display the set temperature about 2seconds.
If 2seconds later, press the “-” button again, the setting temperature will
drop 1 again. If press the “-” button and not loose at least 1second, the
setting temperature will drop rapidly. Till the needed temperature reaches,
then loose the “-” button.
. Setting Working Parameters
5.1 Enter into password interface
CAUTION: password is constitute by three value,original password is:”000″. 1.
Long press ENTER key about 3 second, enter into password interface, show
Page 6
,as follow:
2. Press ENTER key, import the first value 0,”+”key and “-“key be use for
setting value.
3. Press ENTER key affirm, import the second value. 4. Press ENTER key again,
import the third value, then press ENTER key affirm,
enter into menu setting interface. 5. If password input error then return to
main interface, temperature can not be
setting, must import the right password .
5.2 enter into menu setting interface
1. when import right password and then press ENTER key affirm, enter menu
setting interface, the first item of menu is temperature changer; the second
item is ESD switch; the third item is password setting; the fourth item is off
time setting; the fifth item is exit menu.
5.Exit
5.2.1 Temperature changer
Selected the first item, setting temperature changer: press “ENTER” affirm,
and then press “+” key or “-” key select temperature unit, is degree
centigrade, is Fahrenheit, and then press “ENTER” affirm. as following
Page 7
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>