SpaRite Spa and Hot Tub Cover Stand Instructions

SpaRite Spa and Hot Tub Cover Stand

Product Specifications

• Base Plate: 1pc
• Left Support Leg: 1pc
• Right Support Leg: 1pc
• Base Plate Bracket: 1pc
• Main Support Frame: 1pc
• Gas Cylinder: 1pc
• Main Tube Frame: 1pc
• Right Turntable Arm: 1pc
• Left Turnable Arm: 1pc
• Adjustable Arm: 2pcs
• M8 Hex Nut: 2pcs
• M8 Hex Bolt: 6pcs
• 5x80mm Wood Screw: 4pcs
• M8 Round Head Hex Nut: 4pcs
• M8 Washer: 6pcs
• PVC Push Cap: 22pcs
• M8-X40 Hex   Bolt: 2pcs
• M8 Flower Hex Nut: 2pcs
• 1/2 PVC Cap: 4pcs
• Safety Locking Cable: 1pc
• Pivot Steel Bushing: 2pcs
• Rubber Washer: 2pcs
• M8 Round Head Hex Bolt: 2pcs
• 5x18mm Screw: 12pcs
• Rubber Plug: 4pcs
• Rubber Cushion: 2pcs
• Stopper Pin: 2pcs
• Adjustable   Arm Cap: 2pcs
• 5x30mm Wood Screw: 6pcs

Product Usage Instructions

Step 1: Check Parts and Pre-Drill Cabinets

Ensure all parts listed are available. Pre-drill cabinets using the supplied drill bit to prevent damage.

Step 2: Mount Base Bracket

Using the supplied 8mm hex bolts, mount the base bracket to the base as per your measurement. Ensure the base plate bracket is turned in the correct direction.

Step 16: Finalize Installation

Apply all black PVC caps to screws and bolts. The cover lifter is now ready for use.

Frequently Asked Questions

Q: Do I need any additional tools for installation?

A: The product comes with all the necessary hardware for installation. However, you may need a spa wedge (not supplied) for lifting the spa during installation.

Q: Can I adjust the height of the cover lifter?

A: Yes, by adjusting the position of the turntable arms and installing the adjustable arms, you can raise or lower the cover height when in the open position.

PARTS

INSTALLATION INSTRUCTION

• Make sure that you have all the parts from the parts list
• Note: All left and right directions are from standing in front of Hot Tub
• Note: Recommendation to pre drill cabinets before installing wood screws with the drill bit supplied to prevent cabinet damage

1. STEP 1: Using 2– 8mm hex bolts and two nuts, bolt the left support leg to the base.
   • NOTE: Confirm you have the leg turned correctly before mounting. (Fig. 1)
2. STEP 2: Repeat step #1 for the right support leg for the mounting to the cover lifter base. (Fig. 2)
3. STEP 3: Using a tape measure to measure the depth of the hot tub floor to outside edge of the tub. This will confirm where the base plate bracket will be mounted on the base.
   • NOTE: You want the support arms as close as you can to hot tub wall or hot tub rail when measuring. (Fig. 3)
4. STEP 4: Using the 8mm hex bolts supplied, mount the base bracket to the base as per your measurement.
   • NOTE: Make sure the base plate bracket is turned in the right direction. (Fig. 4)
5. STEP 5: Now using a spa wedge “Not Supplied”. Lift the spa up and slide the cover lifter base under the spa until the base plate is flush with the hot tub floor vertically.
   • NOTE: When lifting the spa make sure that you center the cover lifter base on the spa. (Fig. 5)
6. STEP 6: Grab the main cover lifter support frame and slide it onto the left and right support arms. (Fig. 6)
7. STEP 7: Safely stand to side and remove the “Locking Cable” and allow the cover support frame to pivot outwards. (Fig. 7)
8. STEP 8: Slide the cover lifter support frame either up or down to allow the Hot Tub Cover to slide evenly along the top of the spa lip into the cover basket. (Fig. 8)
9. STEP 9: When the support frame is level with spa lip, fasten two self tapping Tek screws on each side of the support brackets where the two holes are pre drilled. (Fig. 9)
10. STEP 10: Now turn the left and right turntable arms so they are vertical with the main tube assembly to allow you to put the stopper pins in.
    • NOTE: Make sure that both arms are even with one another when installing the locking pins. (Fig. 10)
11. STEP 11: The depth of the turn able arms towards the inside of the spa will raise the cover height when in the open position. (Fig. 11)
12. STEP 12: Flip the hot tub cover in half and measure thickness to confirm where to install adjustable arms.
    • NOTE: Two predrilled holes are on the inside edge of each adjustable arm for the self tapping Tek screws. (Fig. 12 & 13)
13. STEP 13: Repeat on the opposite side.
14. STEP 14: Using the four 18mm wood screws provided to fasten the cover lifter base plate, and using the two 30mm wood screws provided to mount both the base plate bracket to the floor.
    • This makes the cover lifter much more sturdy when opening and closing the cover lifter.
    • NOTE: OPTIONAL four 30mm wood screws provided to fasten the main support frame to cabinet for better stability. (Fig. 14)
15. STEP 15: Now apply all black PVC caps to screws and Bolts.
16. STEP 16: Cover lifter is now ready for use.
17. STEP 17: Locking Cable supplied if you would like to secure the cover lifter in the closed position.
    • NOTE: Turn able arms can be turned in closed position for esthetics.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>