SCALEXTRIC C8336 Wireless Controller Instruction Manual
- September 25, 2024
- SCALEXTRIC
Table of Contents
C8336 Wireless Controller
Product Specifications:
-
Product Name: Wireless Controller Accessory Pack
-
Manufacturer: Hornby Hobbies Ltd
-
Manufactured Address: Westwood, Margate, Kent, CT9 4JX, UK
-
EU Authorised Representative: Hornby Italia SRL, Castel Mella
(BS), Italy, 25030 -
Printed in: China
Product Usage Instructions:
Smart-Device Control:
- Connect the smart device to the controller.
Hand Controller Control:
- Turn on the hand controller.
- Connect the hand controller to the device.
Select Throttle Profile:
- Use the hand controller to select the desired throttle
profile.
Regulatory Compliance Information:
You are cautioned that any changes or modifications not approved
by the responsible party could void your authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. It must not
cause harmful interference and must accept any interference
received.
The equipment should be installed and operated with a minimum
distance of 20cm between the radiator and your body.
CE Compliance:
The CE marking indicates compliance with applicable Council
Directives of the European Union.
Warning:
This product must be powered by a LPS power supply.
FAQ:
Q: What should I do if the hand controller is not connecting to
the device?
A: Ensure that the hand controller is turned on and within range
of the device. Try resetting both the controller and the device
before attempting to reconnect.
Wireless Controller Accessory Pack
Instructions
Manufactured By: Hornby Hobbies Ltd, Westwood, Margate, Kent, CT9 4JX, UK EU Authorised Representative: Hornby Italia SRL Viale dei Caduti, 52/A6, Castel Mella (BS), Italy, 25030
Printed in China PI-01555
Smart-Device Control
Connect
1
2
3
4
5
Hand Controller Control
Connect
1
2
3
on off
4
IO
Select Throttle Profile
1
2
3
4
REGULATORY COMPLIANCE INFORMATION
FCC Requirements Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Innovation, Science and Economic Development Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Spark Plug Dongle FCC ID 2ACUF-SA00528 IC 12075A-SA00528
ICES-003/NMB-003 Cet appareil numérique de la classe B est conforme à la norme ICES-003 du Canada.
Spark Plug Dongle FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Spark Plug Hand Throttle FCC ID 2ACUF-C8336 IC 12075A-C8336
CE Compliance For Europe Marking by the CE symbol indicates compliance of this system to the applicable Council Directives of the European Union, including the Radio equipment Directive 2014/53/EU , EMC equipment Directive 2014/30/EU, LVD Directive 2014/35/EU
Warning This product must be powered by a LPS power supply.
Manufacturers name Hornby Hobbies ltd
Manufacturers name Hornby Hobbies ltd
Model Number C8333 SA-00528
Model Number C8336 SSA-00189, SSA-00190
Input parameter 15V DC 1.2A
Input parameter 2 AA Batteries (3V DC)
Product dimensions L 80mm X W 25mm X D 12mm
Product dimensions L 183mm X W 45mm X D 78mm
Operating conditions 0 C to +35 C (for indoor use only) Operating conditions 0 C to +35 C (for indoor use only)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>