FRANKE 780 T45 HE Linear Island Cooker Hood Instruction Manual

FRANKE 780 T45 HE Linear Island Cooker Hood

SAFETY INSTRUCTIONS

Please read this installation and user guide carefully before installing and using the product, paying special attention to the safety instructions. Save these instructions for later use or for the party who may take over the product after you. Disconnect the product from the power supply prior to cleaning or maintenance.

• Diversion of exhaust air must be carried out in accordance with instructions issued by the appropriate authority.
• Exhaust air may not be directed into flues that are used for fumes from items such as gas, wood or oil-burning stoves or fireplaces.
• The distance between the stove and the product must be at least 50cm. For gas hobs, the distance should be increased to 65 cm. Adjust accordingly if the gas hobs manufacturer recommends a higher mounting height.
• For safety reasons, installation and replacement of cables or other types of connectors should only be carried out by a qualified professional.
• Flambéing underneath the product is not permitted.
• If the product is to be used at the same time as products that use energy sources other than electricity, i.e., gas hobs, gas, wood or oil-burning stoves or fireplaces, etc, the room must have an adequate supply of air.
• The product may be used by children from 8 years of age and persons with mental, sensory or physical impairment, or a lack of experience and knowledge, provided they are given information about how the product is to be used.
• Children should not be allowed to play with the product. Children must not undertake cleaning or maintenance of the product unsupervised.
• Accessible parts of the product may become hot when food is being prepared.
• A fire is more likely to spread if the product is not cleaned as frequently as indicated.

Attention! The developer or proprietor is responsible for ensuring installation is carried out correctly and complies with the applicable building regulations.

INSTALLATION

Cooker hood for wall mounting. The cooker hood is equipped with Easy Clean™ motor package, LED lighting and a metal mesh filter. The cooker hood has three speeds, an intensive mode as well as a ventilation mode. Installation, use, care, maintenance etc., are described in these instructions.

TECHNICAL INFORMATION

• Measurements see Fig. 1
• Electrical installation 230 V ~ earthed
• Lighting LED 2 x 2 W

INSTALLATION
Fixing parts, screws for mounting, etc. are supplied with the cooker hood.

Electrical installation
The cooker hood is supplied with a cable and earthed plug for connection to an earthed wall socket. When installing with an extended upper chimney section, take this into account when positioning sockets. The junction box or wall socket must be accessible after installation is complete.

Installation Components

• D 2 pcs:  Brackets for the upper chimney
• E 7 pcs: Wall plugs 5,5 x 35
• F 7 pcs: Screws 4,5 x 39 TORX T25
• G 2 pcs: Screws 2,9 x 9,5
• I 1 pcs: Downdraught damper
• J 1 pcs: Ventilation tape

Installation of wall mounts, marking the wall

Attention! For total height, the distance between the bottom of the cooker hood and the top of the chimney, see measurements Fig. 1. When installing with an extended upper chimney section or if the cooker hood will be fitted with a carbon filter kit, refer to the separate instructions and measurements.

Mark a centre line A above the stove where the cooker hood is to be installed. Draw a horizontal reference line B above the stove, Fig. 2. Place the upper bracket D for the chimney on the wall, as shown in Fig. 2. Mark the bracket’s screw holes on the wall. Place the lower bracket D for the chimney on the wall, as shown in Fig. 2, below the upper bracket, and mark where the screw holes should go on the wall. Mark the screw holes for the mounting of the cooker hood, C, on the wall, as shown in Fig. 2. Drill Ø 3,5 mm holes in the centre of all the marked points. Fasten the consoles to the chimney using the screws F. If the supplied plugs are to be used, drill Ø 5,5 mm holes. Drill the hole 5 mm deeper than the length of the plug. Place wall plugs E in the holes. Check that the screws and plugs used are intended for the wall material (red plastic plug is for attachment in concrete, brick and natural stone).

Assembly

Remove the grease filter and motor unit Fig. 7 Fig. 8. Prior to mounting, screw two screws F into the pre-drilled holes, Fig. 3. Hang the cooker hood and adjust it horizontally Secure it in place with a screw F. Reinstall the motor unit and grease filter.

Tape the downdraught damper I into position using tape J, Fig. 3 If the connection is Ø 125 mm, a reducing coupling sleeve must be used. Secure the reducer to the downdraught damper with tape J.

Connection to exhaust air duct
Connect the cooker hood with a duct or hose ⌀ 160 mm For the lowest noise level, we recommend connection with a duct.

Attention! If the connection is made with a hose, the hose must be installed stretched closest to the connection point, Fig. 4, as this has an impact on both the function and the noise.

Mounting the chimney

Chimney, upper section
Gently bend the two sides of the upper chimney section outwards and hook them on the brackets D. Attach the sides to the upper brackets using screws G ( 2,9 x 9,5 mm), Fig. 5.

Chimney, lower section
Gently bend the two sides of the lower chimney section outwards and secure them between the upper chimney section and the wall. Press the drum down firmly. Make sure it is positioned inside the edge of the fan chassis. Attach at the top between the upper chimney section and the wall. Make sure it snaps into place properly.

Removal of protective plastic
Remove all protective plastic from the filter and any other parts of the product.

INSTRUCTIONS FOR USE

FUNCTION SWITCH

• A. Lighting.
• B. Ventilation mode. The extractor fan runs on low speed for 60 minutes.
• C. Speed 1 on fan motor.
• D. Speed 2 on fan motor.
• E. Speed 3 on fan motor. If the button is held in for 2 seconds, the fan switches to intensive mode. After 7 minutes, the fan motor returns to its previously set mode. The cooker hood can be started and stopped with buttons B-E.

Attention!
For certain installations of the fan intensive mode is not used. It is a good idea to turn on the cooker hood before starting to cook, as this prevents odours from spreading into the room. Adjust the speed of the hood depending on the type of food you are preparing. Preferably allow the cooker hood to run on low speed for a while after cooking. If needed, also use the hood’s low speed when the oven is in use, or after using the dishwasher.

CARE AND MAINTENANCE

Attention! In order to ensure operation, quality and safety after servicing and maintenance, use only original parts.

Cleaning
The cooker hood should be cleaned with a damp cloth and washing-up liquid. With normal usage, the filters must be cleaned at least every other month. Clean more often after intensive use.

Remove the grease filters by opening the snap retainer, Fig. 7 Handle the filters carefully, taking care not to bend them. Soak the filter in a solution of warm water and washing-up liquid. The filter can also be washed in a dishwasher. Refit the grease filters after cleaning, making sure they snap firmly into place.

The motor core, side grilles and fan interior must be cleaned at least twice a year. The motor core is removed by first disconnecting the contact on the side of the motor unit, Fig. 8A. Rotate the latches, Fig. 8B, that lock the motor core in place. Pull the unit outwards so that it is freed from the pins, and then downwards.
Attention! The motor core should not be washed or exposed to moisture! Wipe with a slightly damp cloth and washing-up liquid.

One side grille is detached by lifting up the stop lug with a screwdriver and rotating the grille in the direction marked FREE, Fig. 9. After washing and drying, assemble the parts in reverse order. Check that the parts snap into place and that the motor assembly and electrical connector are properly seated.

REPLACEMENT OF LED LIGHTING AND LED DRIVER

Attention! The replacement of the LED lighting and LED driver must be carried out by an authorised professional. Contact the service organisation.
The lighting and driver must be replaced with an equivalent special light fixture and driver from the manufacturer or its service agent.

SERVICING AND WARRANTY

Check that the fuse is intact. Go through all the functions to check what is not working.
Contact Franke Service
Tel. +46 (0)912-40 500
www.franke.se/service
They can help you fix the problem or refer you to the nearest service agent for fast and effective service. The product is covered by the relevant APPLiA provisions.

PACKAGING AND PRODUCT RECYCLING

The packaging should be deposited at your nearest recycling point. The symbol means that the product must not be treated as household waste. It should insteadbe taken to a collection point for the recycling of electrical and electronic components. By ensuring that the product is dealt with in the correct manner, you are helping to prevent the adverse environmental and health effects that could arise if the product was disposed of as regular waste. For further information on recycling, contact your local authority or waste disposal service, or the store where you purchased your product.

ECO–DESIGN DIRECTIVE
The product meets and is tested in accordance with the eco-design requirements of European Regulation 66/2014.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>