AURIOL 4-LD6634-1 Diy Self Adhesive Wall Clock Instruction Manual

AURIOL 4-LD6634-1 Diy Self Adhesive Wall Clock

Product Information

Specifications

• Model Numbers: 4-LD6634-1, 4-LD6634-2, 4-LD6634-3, 4-LD6634-4
• Product Name: DIY Self Adhesive Wall Clock
• Power Supply: 1 x 1.5V AA LR6 battery (included)

Product Usage Instructions

Introduction
The DIY Self Adhesive Wall Clock is a versatile and customizable wall clock that allows you to create your own unique timepiece.

Contents

• Self-adhesive numbers and decorative elements
• 1 x 1.5V AA LR6 battery
• Quick start guide

Installation and Setup

1. Remove the protective film from the clock movement.
2. Attach the template to the center of the clock movement.
3. Arrange the self-adhesive numbers and decorations as desired on the wall.
4. Mark the position on the wall where you want to place the clock.
5. Stick the reflective elements onto the corresponding black foam elements.
6. Peel off the transparent protective film from the reflective elements.
7. Attach the clock hands to the clock movement using the provided nut.

Battery Replacement
To replace the battery, follow these steps:

1. Remove the clock from the wall.
2. Open the battery compartment at the back of the clock.
3. Replace the old battery with a new 1.5V AA LR6 battery.
4. Close the battery compartment securely.

Cleaning and Maintenance
To clean the clock, use a soft, dry cloth to gently wipe the surface. Do not use abrasive cleaners or solvents as they may damage the finish.

Disposal
When disposing of the clock or batteries, follow local regulations for proper disposal methods to protect the environment.

FAQ

• Q: Can I customize the design of the wall clock?
  A: Yes, you can arrange the self-adhesive numbers and decorations in any way you like to create a personalized design.

• Q: How long does the battery last?
  A: The battery life may vary based on usage, but a typical 1.5V AA LR6 battery can power the clock for several months.

• Q: What should I do if the clock hands are not moving smoothly?
  A: Check if the hands are properly attached to the clock movement. Ensure there are no obstructions blocking their movement.

DIY SELF ADHESIVE WALL CLOCK

Introduction
Congratulations on purchasing your new diy self adhesive wall clock (herein- after referred to as the „product“ or „device“). In choosing this item, you have opted for a high-quality product. These operating instructions form an integral part of this product. It contains important instructions pertaining to its safety, use and disposal. Please familiarise yourself with all the operating and safety instructions before using this product. Only use this product as described and for the purposes stated.
If you give this product to anyone else, please be sure to pass on these documents. Please keep the packaging and operating instructions for future reference.

Intended use
The product is suitable for displaying the time and for using the additional functions described. Any other use or modification of the product is considered improper use. The product is only suitable for indoor use.
The manufacturer is not liable for damage caused by improper use or incorrect operation. The product is not intended for commercial use.

Package contents

Note: Please check the delivery contents after purchase. Check that all parts are present and not defective. If the delivery is incomplete and/or parts are damaged, do not use the product. Contact the service department (see „Processing in the event of a warranty claim“).

• 1 x Clockwork
• 2 x Hands
• 1 x Stencil
• 1 x Fastening hooks for the movement
  • Self-adhesive number panels
  • Lettering and decoration panels for model 4
• 1 x battery 1.5 V AA LR6
• 1 x short manual

Technical specifications

• Quartz movement – 12888
• Dimensions: individually adjustable from approx. 90.0 – 120.0 cm
• Weight of clockwork with clockwork cover: approx. 55 g (excl. batteries)
• Battery: 1 x 1.5 V AA R6/LR6
• – Indicator for DC voltage

Explanation of signal words

**WARNING!| This symbol/word indicates a hazard with a medium level of risk, which, if not avoided, could result in death or serious injury.
---|---
****CAUTION!| ** This symbol/word indicates a hazard with a low degree of risk which, if not avoided, can result in minor or moderate injury.
ATTENTION:| This signal word warns against potential damages to property.
Note:| This signal word is used for additional information.

Explanation of sign

Important safety instructions

Safety instructions for the user

WARNING! Danger of death and accidents for toddlers and children!

Children frequently underestimate the risks. Always keep children away from the product.

• This product may be used by children aged 8 years and older and by persons with reduced physical, sensory or mental capabilities or a lack of experience and knowledge if they are supervised or have been instructed in the safe use of the product and understand the hazards involved. Children are not allowed to play with the product. Cleaning and user maintenance is not to be carried out by children without supervision.
• The packaging material is not a toy. Children can get caught in it and suffocate while playing.
• Do not operate the product if it is damaged.
• Do not expose the product to moisture.
• Only use the product indoors.
• This product does not contain any parts that can be serviced by the consumer.

Safety instructions for the hands

WARNING!
Danger of death and accidents!

The hands of the product are very pointed and sharp-edged. There is an increased risk of injury when attaching to the movement.

• Remove the packaging material from the hands very carefully.
• Handle the hands very carefully and do not touch the sharp edges; if necessary, use suitable gloves.

Battery safety information

WARNING!
Danger of death!

• Keep batteries/rechargeable batteries out of the reach of children. If swallowed, seek medical attention immediately!
• Ingestion can result in burns, perforation of soft tissue and death. Severe burns can occur within 2 hours after swallowing.
• Do not use rechargeable batteries.
• Never recharge non-rechargeable batteries.
• Do not short-circuit batteries/rechargeable batteries and do not open them. This can result in overheating, fire hazards or explosions.
• Never throw batteries/rechargeable batteries into fire or water.
• Do not subject batteries/rechargeable batteries to mechanical stress.

Risk of battery/rechargeable battery leakage

CAUTION!
Risk of injury!
Leaking or damaged batteries/rechargeable batteries can cause burns if they come into contact with skin.
Therefore, wear suitable protective gloves in such cases.

• Avoid extreme conditions and temperatures that may affect batteries/rechargeable batteries, e.g. radiators/direct sunlight.
• If batteries/rechargeable batteries leak, prevent chemicals from coming into con-tact with skin, eyes and mucous membranes. Rinse any affected areas immediately with clear water and seek medical attention.
• In case of leakage from the batteries/rechargeable batteries, remove them from the product immediately to avoid damage.
• Remove the batteries/rechargeable batteries if the product will not be used for a prolonged period.

ATTENTION: Damage to the product

• Only use the specified type of battery/rechargeable battery.
• Insert batteries according to the polarity markings (+) and (-) into the battery/rechargeable battery and the product.
• Clean the contacts on the battery/rechargeable battery and in the battery compartment with a dry, lint-free cloth or cotton swab before inserting them.
• Remove discharged batteries/rechargeable batteries from the product immediately.

Hanging the product safely on the wall
The product is not designed for use in rooms with high humidity (e.g., bathrooms). Before affixing it to the wall, make sure that there is no gas, water or electricity pipe at the connection point. Use suitable screws and dowels (not included in scope of delivery). Be mindful of the wall‘s condition.
The manufacturer assumes no liability for damage caused by improper fastening.

Make sure that:

• no direct heat sources (e.g., heaters) affect the product;
• it is not placed in the path of direct sunlight;
• contact with spraying or dripping water is avoided;
• the product is not mounted in the immediate vicinity of magnetic fields (e.g., loud speakers);
• no foreign bodies can enter the product;
• candles and other open flames are kept away from the product at all times to prevent the spread of fire;

Assembly and initial operation

WARNING!
RISK OF DAMAGE!

• Please remove the numbers in the correct way.

  1. You should very carefully remove the elements along the cutting line and not just randomly.
  2. It is better to remove the unusable gaps first.
  3. Be sure to very carefully detach the elements from the panels, one at a time and in the right direction.

• Insert a 1.5 V AA LR6 battery with the correct +/- polarity.

• Make sure that the hands can move freely.

• Do not turn the hands of the clock with your fingers.

  1. Attach the hook for the clockwork to the wall.

  2. Hang the clockwork on the hook.

  3. Unscrew the nut from the clockwork shaft and attach the template to the clockwork shaft.

  4. The stencil pointer can be shortened to the desired length.

  5. Rotate the stencil pointer to the exact alignment of the digits or indexes every 30°. Mark the position on the wall.
     Note:
     The elements should be removed very carefully along the cutting line and not removed randomly.
     It is better to remove the unusable gaps first.
     Be sure to very carefully detach the elements from the panels, one at a time and in the right direction.

  6. Carefully peel off the white foils from the bottom of the foam elements and glue the foam elements to the previously marked positions.

  7. Carefully peel off the white sheets from the underside of the reflective elements.

  8. Glue the reflective elements onto the corresponding black foam rubber elements.

  9. Carefully peel off the transparent protective films from the top of the reflective elements.

  10. Remove the transparent protective film from the hands.
      WARNING!
      Handle the hands very carefully! The hands of the product are very pointed and sharp-edged. There is an increased risk of injury when attaching to the clockwork.

  11. Attach the hands carefully and exactly with both hands to the shaft of the clockwork at the 12:00 o’clock position.

  12. First attach the shorter hour hand with the round ope-ning to the thicker white plastic. Press it firmly. Then attach the longer minute hand with the oval opening on the metal shaft.

  13. Screw the nut back on to fasten the hands. Note:
      Make sure that the hands can move freely.

  14. Insert the supplied 1.5 V AA LR6 battery into the battery compartment on the back of the movement in the correct polarity +/-.

  15. Set the time by turning the dial on the back of the movement.
      Note:
      Do not turn the hands of the clock with your fingers!

  16. Re-hang the clockwork on the hook on the wall.

  17. That’s it! Enjoy your wall clock.

Replacing the batteries

• Carefully remove the clockwork.
• Remove the battery without damaging it.
• Insert a 1.5 V AA R6/LR6 battery with the correct +/- polarity into the battery compartment.
• Re-hang the clockwork on the hook on the wall.
• Make sure that the hands can move freely.
• Do not turn the hands of the clock with your fingers.

Removing the wall clock

1. To remove the elements, carefully heat them with a hairdryer.
2. Carefully release the elements from the wall.

Cleaning instructions

Improper cleaning can damage the product. Avoid any aggressive cleaning agents, any brushes with metal or nylon bristles, or any sharp or metallic cleaning objects, such as knives, hard spatulas and the like. These can damage the surface. Clean the product with a soft, dry, lint-free cloth, such as that used for cleaning glasses lenses.

Storage
If the product is not used for a long time, remove the battery, clean and store the product away from sunlight in a dry, cool place, preferably in the original packaging.

Disposal
The product and packaging material are recyclable. Please dispose of them se- parately for better waste management. To learn options for disposal of the used product, please contact your municipal or city administration.

Check the labelling on the packaging material when separating waste – they are marked with abbreviations (a) and numbers (b) with the following meaning:

1-7: Plastics
20–22: paper and cardboard
80-98: Composites.

Disposal of the electrical device
The symbol with the crossed-out dustbin means that electrical and electronic equipment must not be disposed of together with household waste. Consu- mers are legally obliged to dispose of electrical and electronic equipment at the end of their life separately from unsorted municipal waste. This is to ensure environmentally friendly and resource-saving recycling. Batteries and rechar- geable batteries that are not an integral part of the electrical or electronic device and can be removed without being destroyed, must be separated from the device before handing it in at a collection point for designated disposal.

The same applies to lightbulbs that can be removed from the device without being destroying. Owners of electrical and electronic equipment who are private individuals can hand them in at the collection points operated by the public waste disposal agencies or at the collection points set up by manufacturers or distributors. Returning used devices is free of charge. This free take-back obligation applies both to purchases in shops and to home deliveries.

The place of performance of the obligation to take back is the same as the place of performance of the delivery. Transport costs may not be charged for returned equipment. In general, distributors have the obligation to ensure the free return of used devices by providing suitable return facilities within a reasonable distance. Consumers have the option to return an old device free of charge to a distributor who is obliged to take it back if they purchase an equivalent new device with essentially the same function.

This option is also available for deliveries to a private household. In the case of distance selling retailers, the option of free collection when purchasing a new device is limited to heat exchangers, display screen devices, and large devices that have at least one outer edge with a length of more than 50 cm. The distributor must ask the consumer at the time of concluding the sales contract about any corresponding intention to return the product. Beyond this, consumers can hand in up to three old devices of one type free of charge at a distributor’s collection point without this being linked to the purchase of a new device. However, the edge lengths of the respective devices must not exceed 25 cm. Remove the battery without destroying it before disposal and dispose of it separately (see Disposal of batteries).

Disposal of batteries
The accompanying symbol indicates that batteries must not be disposed of with normal household waste. Defective or used batteries must be recycled in accordance with Directive 2006/66/EU and its amendments. Consumers are legally obliged to hand in all batteries, regardless of whether they contain harmful substances, such as:
Cd = cadmium, Hg = mercury, Pb = lead, Li = lithium or not, to a collection point in their municipality/district or a retail outlet to ensure environmentally friendly disposal and to recover valuable raw materials, such as cobalt, nickel or copper. The return of batteries is free of charge.

WARNING! Environmental damage due to incorrect disposal of batteries!

Some of the possible contents, such as mercury, cadmium and lead, are poisonous and, if not disposed of properly, endanger the environment. Heavy metals, for example, can have harmful effects on the health of humans, animals and plants and accumulate in the environment and in the food chain, and then enter the body indirectly via food.

WARNING!
Risk of explosion!
With used batteries containing lithium (Li = lithium), there is a high risk of fire. Therefore, special attention must be paid to the proper disposal of used and rechargeable batteries containing lithium. Incorrect disposal can also lead to internal and external short circuits due to thermal effects (heat) or mechanical damage. A short circuit can lead to a fire or an explosion and have serious consequences for humans and the environment. For this reason, tape off the poles of lithium-based batteries prior to disposal in order to avoid an external short circuit. Batteries that are not permanently installed in the device must be removed and disposed of separately before disposing of the device. Please return batteries only when fully discharged! Use rechargeable batteries instead of disposable batteries whenever possible.

Simplified EU declaration of conformity
Digi-tech gmbh hereby declares that the diy self adhesive wall clock
4-LD6634-1, 4-LD6634-2, 4-LD6634-3, 4-LD6634-4 complies with the directives RoHS 2011/65/EU and EMC 2014/30/EU.
You can download your operating instructions and declaration of conformity here: www.digi-tech-gmbh.com/downloads
Then click on the magnifying glass and enter the article number 452421_2310.

The digi-tech gmbh warranty

This device has a 3-year warranty valid from the date of purchase. In the event of defects in this device, you have legal rights against the seller of the device. These statutory rights are not limited by our warranty set out below.

Warranty terms
The warranty period begins on the date of purchase. Please keep the receipt. This document is required as proof of purchase. If a material or manufacturing defect occurs within three years of the date of purchase of this device, the device will be repaired or replaced – at our discretion – by us free of charge. This warranty requires that the defective device and the purchase receipt are presented within the three-year period with a briefly written statement stating the nature of the defect and when it occurred. If the defect is covered by our warranty, you will receive the repaired or a new device back. No new warranty period begins with the repair or replacement of the device.

Warranty period and statutory claims for defects
Statutory warranty rights do not extend the warranty period. This also applies to replaced and repaired parts. Any damage or defects already present at the time of purchase must be reported immediately after unpacking. After the warranty has expired, any repairs are subject to a charge.

Scope of Warranty
The device was carefully manufactured according to strict quality guidelines and carefully checked before delivery. The warranty applies to material or manufacturing defects. This warranty does not cover parts of the product that are subject to normal wear and tear and can therefore be regarded as wear parts or for damage to fragile parts, e.g. switches, batteries or parts made of glass. This warranty is void if the unit has been damaged or improperly used or maintained. For proper use of the device, all instructions given in the manual must be strictly observed. Uses and actions that are advised against or warned against in the operating instructions must be avoided at all costs. The device is designed exclusively for private and not for commercial use. The warranty expires in the event of abusive or improper handling, the use of force or repairs that were not carried out by our authorised service branch.

Processing in the event of a warranty claim
To ensure that your request is processed quickly, please follow the instructions below:

• For all inquiries, please have the receipt and item number (452421_2310) ready as proof of purchase.
• Please refer to the type plate, engraving, title page of your manual (bottom left) or to the sticker on the back or underside for the item number.
• If functional errors or other defects occur, first contact the following service department by phone or email.

You can download these instructions and many other manuals, product videos and software at www.lidl-service.com.

This QR code will take you directly to the Lidl service page (www.lidl- service.com), where you will be able to access your operating instructions by entering the article number (452421_2310).

Service
Inter-Quartz GmbH, Valterweg 27A, 65817 Eppstein, GERMANY
Email: support@inter-quartz.de
Telephone: +49 (0)6198 571825
00800 5515 6616
8009 4403

Supplier
Please note that the following address is not a service address. Contact the Service Office named above first.
digi-tech gmbh, Valterweg 27A, 65817 Eppstein, GERMANY

Year of manufacture: 2024
IAN 452421_2310, Art.no.: 4-LD6634-1, 4-LD6634-2, 4-LD6634-3, 4-LD6634-4

References

• art.no
• Sie sehen hier eine soeben freigeschaltete Homepage
• Service.com is for sale | www.brandforce.com
• Downloads | digi-tech GmbH
• de/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>