BONELLI BF-2 Pella Reserve Multi Slide Doors Owner’s Manual

September 24, 2024
BONELLI

BONELLI BF-2 Pella Reserve Multi-Slide Doors

Specifications

  • Glazing Type: Dual-Pane Tempered Insulating Glass, Triple-Pane Tempered Insulating Glass, Dual-Pane Laminated Insulating Glass Insulated Glass Options/Low-E Types: Low-E 366, Low-E 366/i89, Low-E 270
  • Glass: Tempered Glass, Laminated Glass (Dual-Pane only)
  • Gas Fill: Argon, Air (High-Altitude)
  • Frame and Panels: Thermally Broken Aluminum
  • Finishes: Satin Anodized, Black Anodized
  • Hardware Finishes: Satin Nickel, Black

Product Usage Instructions

Installation

Ensure the opening for the bifold doors is properly measured and prepared. Follow the installation guidelines provided in the user manual to correctly install the doors.

Operation

To open the bifold doors, gently push them to one side until fully extended. To close them, pull them back together and secure the locking mechanism if available.

Maintenance

Regularly clean the glass panels and frames with a mild soap solution and a soft cloth. Avoid using abrasive cleaners or materials that may damage the finish.

FAQ

Q: Can I install these bifold doors on my own?

A: While it is possible for DIY installation, we recommend consulting a professional for proper installation to ensure safety and functionality.

Q: What should I do if the doors become difficult to operate?

A: Check for any obstructions in the tracks or hinges that may be causing the issue. Lubricate the moving parts with a silicone-based lubricant if needed.

Q: Are these doors energy-efficient?

A: Yes, the dual-pane and triple-pane options with Low-E coatings and Argon gas fill provide excellent insulation properties, making them energy- efficient.

Document Navigation Tips:

  • Items listed in the table of contents above are active links that will take you to the corresponding page.
  • The logo on each page is a link back to this table of contents.
  • Bookmarks are also included in this PDF document and are available as an additional navigation option.

Features and Options

Features and Options

Glazing
Glazing Type
Dual-Pane Tempered Insulating Glass
Triple-Pane Tempered Insulating Glass
Dual-pane laminated Insulating Glass
**Insulate d Glas s Options/Low- E Types
Low-E 366
Low-E 366/i89
Low-E 270
****
Glass **
Tempered Glass
Laminated Glass (Dual-Pane only)
**Ga s Fill
Argon
Air (High-Altitude)
****
Frame and Panels
Thermally Broken Aluminum
****
Finishe ****s 1
Satin Anodized, Black Anodized
****
Hardware
****
Finishe ****s** 1
Satin Nickel, Black

Glazing Performance – Total Unit

Glazing Thickness| Type of Glazing| NFRC Certified Product #| Glass (mm)| Gap Fill| Performance Values 1| Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
---|---|---|---|---|---|---
Ext.| Int.| U-Factor| SHGC| VLT| CR| U. S.| Canada 2
Zone| ER| Zone
Dual-Pane -Narrow|  |  |  |  |  |  |  |  | N| NC| SC| S|  | CA
1″| 366/ clear| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1″| 366/ i89| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1″| 270/ clear| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1″| 366/ clear| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1″| 366/ i89| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1″| 270/ clear| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
Dual-Pane Laminated – Narrow
1-1/4″| 366/ clear| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-1/4″| 366/ i89| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-1/4″| 270/ clear| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-1/4″| 366/ clear| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1-1/4″| 366/ i89| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1-1/4″| 270/ clear| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
Dual-Pane – Wide
1″| 366/ clear| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1″| 366/ i89| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1″| 270/ clear| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1″| 366/ clear| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1″| 366/ i89| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1″| 270/ clear| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
Dual-Pane Laminated – Wide
1-1/4″| 366/ clear| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-1/4″| 366/ i89| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-1/4″| 270/ clear| PENDING| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-1/4″| 366/ clear| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1-1/4″| 366/ i89| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1-1/4″| 270/ clear| PENDING| 5| 5| Air|  |  |  |  |  |  |  |  |  |
Glazing Thickness| Type of Glazing| NFRC Certified Product #| Glass (mm)| Gap Fill| Performance **Values 1| Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
---|---|---|---|---|---|---
Ext.| Mid.| Int.| U-Factor| SHGC| VLT %| CR| U. S.| Canada 2
Zone| ER| Zone
Triple-Pane – Narrow|  |  |  |  |  |  |  |  |  | N| NC| SC| S|  | CA
1-5/8″| 366/ clear/ 180| PENDING| 5| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-5/8″| 366/ 180/ i89| PENDING| 5| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-5/8″| 270/ clear/ 180| PENDING| 5| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-5/8″| 366/ clear/ 180| PENDING| 5| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1-5/8″| 366/ 180/ i89| PENDING| 5| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1-5/8″| 270/ clear/ 180| PENDING| 5| 5| 5| Air|  |  |  |  |  |  |  |  |  |
Triple-Pane – Wide**
1-5/8″| 366/ clear/ 180| PENDING| 5| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-5/8″| 366/ 180/ i89| PENDING| 5| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-5/8″| 270/ clear/ 180| PENDING| 5| 5| 5| Argon|  |  |  |  |  |  |  |  |  |
1-5/8″| 366/ clear/ 180| PENDING| 5| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1-5/8″| 366/ 180/ i89| PENDING| 5| 5| 5| Air|  |  |  |  |  |  |  |  |  |
1-5/8″| 270/ clear/ 180| PENDING| 5| 5| 5| Air|  |  |  |  |  |  |  |  |  |

  • R-Value = 1/U-Factor
  • SHGC = Solar Heat Gain Coefficient
  • VLT % = Visible Light Transmission
  • CR = Condensation Resistance
  • ER = Canadian Energy Rating
  1. Glazing performance values are calculated based on NFRC 100, NFRC 200, and NFRC 500.
    • ENERGY STAR® values are updated to 2023 (version 7) criteria.
  2. The values shown are based on Canada’s updated ENERGY STAR® 2020 initiative.

Special Sizes and Dimensions

Frame Height Panel Width Panel Height
Minimum Maximum Minimum

Maximum
36″| 132.5″| 18″| 39″| 32.301                 129″

Special Sizes are available in 1/4″ Increments

Dimension Formula
__Rough Opening Width __ FW + 0.5″
__Rough Opening Height __ FH + 0.5″
Panel Height: Standard Sill __ FH – 3.6988″
Panel Height: Low Profile (ADA) Sill __ FH – 3.699″
Panel Height: Flush Sill __ FH – 3.6988″
__Panel Projection __ Panel width – 0.9″
Clear Opening (Approximate) __ FW – Panel Stack – 3.187″

Panel Stack

One- Side No Handle Set (Approximate)

| # Panels x 2.25″ + (# Panels – 1) x 0.62″
Panel Stack One- Side w/ Handle Set (Approximate)|
# Panels x 2.25″ + (# Panels – 1) x 0.62″ + 5.05″
Panel Width| One Way No Passage Door| (FW – (TP-1) * 0.1574″ – 2.806″ ) / TP
One Way with Passage Door|
(FW – (TP-1) 0.1574″ – 2.806″ ) / TP
Split No Passage Door| (FW – (TP-2)
0.1574″ – 2.806″ – 0.473″ ) / TP
Split with Passage Door| (FW – (TP-2) * 0.1574″ – 2.806″ – 0.275″ ) / TP
KEY

FW = Frame Width
FH = Frame Height
TP = Total # of panels
PW = Panel Width
PH = Panel Height
ROW = Rough Opening Width
ROH = Rough Opening Height

  • X = Venting, O = Fixed. All dimensions are in inches.
  • Non-rated, passed internal Air/Water/Structural testing
  • Those noted as NR are not AAMA/WDMA performance certified.
  • Custom-sized units in 1/8″ increments.
  • Doors are viewed from the exterior.
  • Contact your local sales representative for more information.

Design Data Panel Configurations

  • A  indicates the Active Passage Door where applicable.
  • P indicates a swinging Passive Door where handle set matches Passage Door.
  • Maximum performance when glazed with the appropriate glass thickness.
  • Those noted as NC are not AAMA/WDMA performance certified.
  • Doors are configured from left to right as viewed from the exterior.
  • Minimum to Maximum door width dimensions refer to frame-to-frame dimensions.
  • Contact your local sales representative for more information.
  • A indicates the Active Passage Door where applicable.
  • P indicates a swinging Passive Door where applicable.
  • Maximum performance when glazed with the appropriate glass thickness.
  • Those noted as NC are not AAMA/WDMA performance certified.
  • Doors are configured from left to right as viewed from the exterior.
  • Minimum to Maximum door width dimensions refer to frame-to-frame dimensions.
  • Contact your local sales representative for more information.
  • A indicates the Active Passage Door where applicable.
  • P indicates a swinging Passive Door where the handle set matches the Passage Door.
  • Maximum performance when glazed with the appropriate glass thickness.
  • Those noted as NC are not AAMA/WDMA performance certified.
  • Doors are configured from left to right as viewed from the exterior.
  • Minimum to Maximum door width dimensions refer to frame-to-frame dimensions.
  • Contact your local sales representative for more information.
  • A indicates the Active Passage Door where applicable.
  • P indicates a swinging Passive Door where handle set matches Passage Door.
  • Maximum performance when glazed with the appropriate glass thickness.
  • Those noted as NC are not AAMA/WDMA performance certified.
  • Doors are configured from left to right as viewed from the exterior.
  • Minimum to Maximum door width dimensions refer to frame-to-frame dimensions.
  • Contact your local sales representative for more information.
  • A indicates the Active Passage Door where applicable.
  • P indicates a swinging Passive Door where handle set matches Passage Door.
  • Maximum performance when glazed with the appropriate glass thickness.
  • Those noted as NC are not AAMA/WDMA performance certified.
  • Doors are configured from left to right as viewed from the exterior.
  • Minimum to Maximum door width dimensions refer to frame-to-frame dimensions.
  • Contact your local sales representative for more information.

Detailed Product Description

Frame

  • Extruded aluminum head and jambs with thermal breaks [Block frame].
  • Extruded aluminum [Standard sill with thermal breaks] [Flush sill with thermal breaks] [U-channel sill].
  • Frame Finish is [Satin Anodized] [Black Anodized].
  • Frame Depth 4-1/2″

Door Panels

  • Extruded aluminum [Narrow Stiles/Rails] [Wide Stiles/Rails]with thermal breaks.
  • Corners are secured with metal fasteners.

Weatherstripping

  • Dual-durometer extruded polymer along head and jambs of door frame.
  • Extruded pile with quiet fin at top and sides of door panel.
  • Dual extruded piles with quiet fin at bottom of door panel on flush and u- channel sills.
  • Dual-durometer extruded polymer along standard sill

Glazing System 1

  • Quality fully-tempered float glass complying with ASTM C 1048.
  • High-altitude glazing is available.
  • Silicone-glazed, 1” double-pane, dual-seal, insulating glass
  • [[366/Clear] [366/i89] [270/Clear] Low-E [with argon]]
  • Silicone-glazed, 1-1/4” double-pane, dual-seal, laminated, insulating glass.
  • [[366/Clear] [270/Clear] Low-E [with argon]]
  • Silicone-glazed, 1-5/8” triple-pane, dual-seal, insulating glass
  • [[366/Clear/180] [366/180/i89] [270/Clear/180] Low-E [with argon]]. Hardware
  • Handles
    • Contemporary multi-point lock lever with Euro-cylinder in [satin nickel] [black].
  • Locks
    • Multi-point locking system with deadbolt and additional locking points at jamb, sill, and head that will engage simultaneously. Lever located at 36″ from bottom of panel.
  • Passive Panels and Windows
    • Multi-point lock system with shoot-bolts at the head and sill
    • Dual Point Handle [without thumb-turn][with thumb-turn]
  • Hardware finish is [Satin Nickel] [Matte Black].
  • Hardware handle location from bottom of the panel to center of lock thumb turns [frame height >78″ is 36″] [frame height <78″ is 16″].

Unit Sections Frame

Unit Sections – Frame Types and Glazing Options Overview

NARROW STILE

GLAZING OPTIONS

Unit Sections – Block Frame Dual-Pane Glazing

Scale 3″ = 1′ 0″ All dimensions are approximate.

Unit Sections – Block Frame Dual-Pane Glazing

Unit Sections – Block Frame Dual-Pane Glazing

  • Bonelli 2024 Architectural Design Manual
  • Division 08 – Openings
  • Windows and Doors
  • www.bonelli.com

Documents / Resources

| BONELLI BF-2 Pella Reserve Multi Slide Doors [pdf] Owner's Manual
BF-2, BF-3, BF-4, BF-2 Pella Reserve Multi Slide Doors, BF-2, Pella Reserve Multi Slide Doors, Reserve Multi Slide Doors, Multi Slide Doors, Slide Doors, Doors
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals