Copper M685 2L Electric Pot Instructions

Copper M685 2L Electric Pot

Product Usage Instructions

Before first use, clean the electric pot with warm water + detergent. Boil water and pour it out before using it to cook food.

• Slide the switch to 0 for no heating.
• Slide the switch to I for 300W heating.
• Slide the switch to II for 600W heating.
• Use only the supplied power cord.
• Dry the bottom of the pan before use.
• Do not leave the product unattended while in operation.
• Place the product on a flat surface away from heat sources and other electrical appliances.
• Avoid touching steam released from the glass cover.
• Do not exceed or go below the water level limits.
• Avoid contact with hot objects and do not immerse in water for cleaning.

FAQ

• Q: What should I do if the indicator light does not turn on?
• A: Check the power connection and ensure the switch is set to either I or II.
• Q: Can I use the electric pot without the glass cover?
• A: It is recommended to cover the pot with the glass cover while boiling water to prevent splashing and accidents.
• Q: How do I know if the safety device has been activated?
• A: The power will be automatically cut off if the temperature exceeds the preset limit, indicated by the indicator light turning off. Allow it to cool before resetting.

Instructions for Use

• Please read and retain these instructions for future reference

• The figures are for illustration purposes only.

• The actual product may look different.

Notes
Before use, please clean it with warm water + detergent, then boil the water and pour it out before using it to cook food!

Operating Instructions

1. Slide the switch to “0” – No indicator light and no heating when the device is not switched on.
2. Slide the switch to “I” – The indicator light goes on, and the product starts heating. The first gear is 300W.
3. Slide the switch to “II” – The indicator light goes on, and the product starts heating. The second position is 600W.
4. The product has dual protection devices of temperature control and thermal fuse. After power-on, the indicator light is always on.

When the temperature exceeds the preset safety temperature upper limit of the product, the safety device will automatically cut off the power.
After the temperature drops, the temperature control device will automatically reset. When the temperature control fails, it is a product failure.

Safety instructions

Please read this manual carefully before using the machine.
Please keep the manual safe for future reference.
Please follow the important safety warnings below. Failure to follow the safety warnings may result in injury and/or harm to you and other people. Always follow the information in this instruction manual.

1. The product shall be used together with the power cord supplied, and other power cords should not be used.
2. Dry the bottom of the pan prior to use.
   • Stay at the side while the product is working. Do not leave the product unattended to avoid accidents.
   • Do not place the product within the reach of children or mentally handicapped persons to prevent scalding.
3. When using, place the product on a flat surface, not close to other heat sources, nor on other electrical appliances.
4. When the product is operating, do not touch the steam released from the glass cover to prevent scalding.
5. Do not add water beyond the maximum water level to prevent boiling water from splashing out and scalding people, nor lower than the minimum water level to avoid product damage caused by dry burning of the heating plate. Cover the glass cover when boiling water.
6. For use for the first time, add water to the maximum water level, and then boil the water and pour it out, to clean the pan body.
7. Do not hang the power cord around the table in contact with hot objects.
8. Do not immerse the pan body in water or other liquids for cleaning to avoid short circuits.
9. Please use the power socket with a voltage consistent with the voltage indicated on the product nameplate.
10. In case of power cord damage, it must be replaced with a special flexible cord or a special component purchased from its manufacturer or maintenance department.
11. The power supply cannot be connected under the following conditions: no water in the pan, when adding water, cleaning, or moving the product.

In case of any fault, please send the product to the special maintenance center for maintenance prior to use. The user shall not repair it by himself. To avoid electrical hazards, please do not disassemble the bottom cover or the power cord by yourself.
This product is only available for use indoors or in similar places.
Use method:

Boil water

1. Remove the cover, add clean water, neither below the minimum water level nor above the maximum water level, and then replace the cover.
2. Plug the power plug into the power supply, slide the switch to “II”, the indicator light goes on, and the product starts heating.
3. After a few minutes, the water begins to boil. After 3 minutes, turn the switch knob to “O”, the indicator light goes off, and the product stops heating.

Cook noodles

1. Remove the cover, add clean water, neither below the minimum water level nor above the maximum water level, and then replace the cover.
2. Plug the power plug into the power supply, slide the switch to “II”, the indicator light goes on, and the product starts heating.
3. After a few minutes, the water begins to boil. Put the noodles in the pan and the water temperature reduces. After the water boils again, add any seasoning and mix evenly

Turn the switch knob to “O”, the indicator light goes off, and the product stops heating.

Hot pot/Soup/Sauces

1. Remove the cover, add the items to the pan, and then replace the cover.
2. Plug the power plug into the power supply.
3. For slower cooking slide the switch to “I”. For faster cooking slide the switch to “II”. The indicator light goes on, and the product starts heating.
4. After a few minutes, the food will start to simmer. Allow to simmer for a few minutes until fully heated. Then serve and enjoy…

Fried steak, Fried chicken wings

1. Plug the power plug into the power supply, slide the switch to “I”, the indicator light goes on, and the product starts heating. If heating quickly, turn the switch knob to “II”.
2. Remove the cover, add the right amount of oil, then cook the meat.
3. After all the meat is fried, turn the switch knob to “O” and turn off the power supply.

Trouble Shooting

several minutes, Pour cold water to proceed
The water is smells| New unused product| Boil water several times before using and pour out. If the situation continues, fill in water to the highest level and add two teaspoons of soda, boil and pour it out, then wash again.

Cleaning And Maintenance

1. After use, please unplug the power plug from the power socket in time. After the pot is cooled, all parts can be cleaned with detergent and a sponge. Keep it in a well-ventilated and dry place if it will not be used for long time to avoid humidity and impaired performance.
2. Do not immerse the whole machine in water for cleaning, or electric leakage or an accident may happen. The lid can only be cleaned in water.
3. Do not use hard steel wire to clean, so as not to damage the surface. For cooked-on stains, fill the pan with hot water to soak and soften and then clean with hot water and detergent.

Product Specifications

M685/60425 ELECTRIC SAUCEPAN INSTRUCTION AMENDMENT NOTICE

PLEASE NOTE THAT THE WATTAGE INFORMATION WITHIN THE INSTRUCTION MANUAL AND ON THE COLOURBOX IS INCORRECT DUE TO A PRINTING ERROR.
THE CORRECT WATTAGE DETIAL IS 85-89 WATTS ON SETTING 1.

CONTACT

CUSTOMER SERVICES

• Distributed by
• UK: The Enterprise Department Ltd.
• 11 Bridge Street, Bishops Stortford, Herts, UK, CM23 2JU
• Tel: 0330 331 0300

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>