Lowes EP25435US Electric Barbecue Grill User Manual

Lowes EP25435US Electric Barbecue Grill

Electric Barbecue Grill Parts

IMPORTANT: Your Electric Barbecue Grill has been shipped with the components shown below. Check everything carefully before assembly or use. If any part is missing or damaged, do not use this product and contact the after- sales service center.

PRODUCT DIAGRAM

1. Lid
2. Bowl
3. Cooking Grill
4. Heat Reflector Plate
5. Heating Element
6. Handle (x2)
7. Temperature Control
8. Lid Handle
9. Air Vent
10. Hinge Bracket
11. Connection Part
12. Drip Tray
13. Pillar
14. Base
15. Locking Pin

SCREWS AND WASHER COMPONENTS

Assembly Instructions

NOTE: Tighten all connections by hand first. Once assembly is complete, tighten all connections fully.

Step 1 – Attach Pillar to Base

• Hardware: M6X20 Medium Screw – 4pcs
  • Lock Washer – 4pcs
  • Flat Washer – 4pcs

Unscrew and put aside the four (4) M6X20 medium screws on one end of the pillar. Add four (4) flat washers on the end of the pillar, then put the pillar on the base and screw the base to the pillar using the four ( 4) M6X20 medium screws previously removed.

Step 2 – Connection Part

• Hardware: M6X20 Medium Screw – 4pcs
  • Lock Washer – 4pcs
  • Flat Washer – 4pcs

Unscrew and put aside the four (4) medium screws M6X20 on the other end of the pillar. Align the pillar to the bottom of the connection part, then screw the pillar to the bottom of the connection part using the four (4) M6X20 screws previously removed.

Step 3 – Attach the Bowl

• Hardware: M6X20 Medium Screw – 5pcs
  • M6 Large Wing Nut – 5pcs
  • Lock Washer – 5pcs
  • Flat Washer – 5pcs

Place the assembled base on flat ground. Unscrew and put aside the five (5) large wing nuts M6 on the top connection part. Place the bowl on the top of the connection part and affix the bowl to the connection part using the five (5) M6 medium wing nuts previously removed.

Step 4 – Bowl Handles

• Hardware: M6 Large Wing Nut – 4pcs
  • Lock Washer – 4pcs
  • Flat Washer – 4pcs
  • Long Screw M6 x 45-4pcs

Unscrew the two (2) M6 large wing nuts from each of the two (2) handles with four long screws M6 x 45 and put aside. Affix the two (2) handles to either side of the bowl by using the M6 large wing nuts previously removed.

Step 5 – Bowl Hinge Bracket

• Hardware: MSX12 Small Screw – 2pcs
  • Flange Nut – 2pcs
  • Lock Washer – 2pcs
  • Flat Washer – 2pcs

Unscrew the two(2) Flange nuts MS from the hinge bracket and put aside. Use two(2) MSX12 small screws and put them through the holes in the bowl. Affix the hinge bracket to the bowl using the two(2) Flange nuts MS previously removed.

Step 6 – Lid Hinge Bracket

• Hardware: MSX12 Small Screw – 2pcs
  • MS Small Wing Nut – 2pcs
  • Lock Washer – 2pcs
  • Flat Washer – 2pcs

Unscrew the small wing nut on the hinge bracket. Affix the hinge bracket to the lid using the small wing nut previously removed.

Step 7 – Locking Pin

• Hardware: Locking Pin MS*123 – 1pc
  • MS Small Wing Nut – 1pc
  • Lock Washer – 1pc
  • Flat Washer – 1pc

Affix the hinge bracket on the bowl to the hinge bracket on the lid using the locking pin. Lock them using the MS small wing nut.

Step 8 – Air Vent

• Hardware: MSX12 Small Screw – 1pc
  • MS Small Wing Nut – 1pc
  • Lock Washer – 1pc
  • Flat Washer – 1pc

Affix the air vent in the middle of the lid.

Step 9 – Lid Handle

• Hardware: M6 Large Wing Nut – 2pcs
  • Lock Washer – 2pcs
  • Flat Washer – 2pcs

Affix the lid handle to the lid using two (2) M6 large wing nuts.

Step 10 – Heating Components

• Hardware: MSX12 Small Screw – 2pcs
  • MS Small Wing Nut – 2pcs
  • Lock Washer – 2pcs
  • Flat Washer – 2pcs

Place the heat reflector plate in the bowl, then place the heating element in the bowl. Affix using MSX12 small screw and then lock using MS nut.

Step 11 – Cooking Grill

Place the cooking grill in the bowl.

Step 12 – Oil Pan

Place the Oil pan into the Connection part (part 11)

Using the Temperature Control

Powering Up the Barbecue

1. Make sure the temperature control knob is fully turned to the “OFF” position.( Fig.1 part 7)
2. Plug the temperature controller fully into the heating element front mounting bracket. (Fig. 2,). With the temperature dial facing upwards, the controller probe (and power connection holes) should be inserted until the controller front wall is snug against the heating element front mounting bracket.
   • Hints: The tip of the temperature probe should be above the nearby punch hole on the reflector plate when it is fully inserted ( Fig.3)
3. Plug the other end of the temperature control knob into a dry ground-fault circuit-interrupter (GFCI) power outlet. WARNING: DO NOT use an extension cord. ( see IMPORTANT SAFEGUARD again )
4. Then adjust the setting on the control knob to the desired temperature level.

Settings on the temperature controller are indicated by temperature marks on the upper circular dial, including the “OFF” position marking. The unit is usually packed with the temperature dial set at the “OFF” position.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>