ACOM 2100 6m Linear Amplifier Instruction Manual
- September 4, 2024
- ACOM
Table of Contents
ACOM 2100 6m Linear Amplifier
Product Information
Specifications
-
Frequency Coverage: All amateur bands in the 1.854 MHz frequency range (extensions and/or changes on request)
-
Power Output: 1500 W PEP or continuous carrier, no mode limit
-
Intermodulation Distortion: Better than 32 dB below rated output
-
Hum and Noise: Better than 40 dB below rated output
-
HARMONIC OUTPUT SUPPRESSION
- 1.8‑29.7 MHz ‑ better than 50 dB below rated output
- 50‑54 MHz ‑ better than 66 dB below rated output
-
Mains Power Supply Voltage: 85-132 VAC / 170-264 VAC (100, 110, 120, 200, 210, 220, 230 & 240 V nominal taps, +10% -15% tolerance), 50-60 Hz, Single phase
-
Mains Power Consumption: 3500 VA at rated output
-
Safety and Electromagnetic Compatibility: Complies with CE safety and electromagnetic compatibility requirements, as well as with the US Federal Communications Commission (FCC) regulations
-
Input and Output Impedances:
- Nominal value: 50 Ohm unbalanced, UHF (SO‑239) type connectors
- Input circuit: broadband, SWR less than 1.3:1, 1.8‑54 MHz continuously (no tuning, no switching)
- Bypass path SWR less than 1.1:1, 1.8‑54 MHz continuously
- Output (antenna) impedance matching capability: SWR up to 3:1 or higher at reduced output levels
-
RF Gain: 13.5 dB typically, frequency response less than 1 dB (50-85 W drive power for rated output)
-
SIZE & WEIGHT
- Operating (excluding connected cables) WxDxH: 445x375x205 mm, 29.3 kg (17.6×14.8×8.1 inches, 64.6 lbs.)
- Shipping
- Amplifier carton, WxDxH: Approx. 610x490x380 mm, 17.0 kg (24.1×19.3×15.0 inches, 37.5 lbs.)
- Transformer carton, WxDxH: Approx. 330x390x370 mm, 16.5 kg (13.0×15.4×14.6 inches, 36.4 lbs.)
-
OPERATING ENVIRONMENTS
- Temperature range: 0…+50 °C (32 °F to 122 °F)
- Relative air humidity: up to 95% @ +35 °C (95 °F)
- Height above sea level: up to 3050 m (10000 ft) without output deterioration
Product Usage Instructions
OLED Comment Display
All amplifier status indications are explained via detailed text displayed
on the high brightness and contrast OLED display. The upperline’s strip on the
display always reads peak forward power.
No Antenna Tuner Needed
No heavy outboard antenna tuners required for antenna SWR up to 3:1 (and
higher on some bands). Your amplifier will enable you to change antennas
virtually instantaneously and allow you to use your antennas over wider
frequency ranges.
Three Antenna Outputs
Three antenna outputs are selectable using a push button on the front
panel.
Broadband Input Matching
Resulting in a very good load to the transceiver over the entire spectrum
from 1.8 MHz up to 54 MHz.
Less Noise in the Shack
The input bypassing and the vacuum antenna relays are virtually silent even
in the CW QSK mode thanks to specially designed mounting hardware.
Transceiver-Independent
The amplifier operates without special signals from the transceiver. Ground
on TX and 85 W RF drive power are sufficient.
Tube Protection
Permanent monitoring and protection of plate and grid voltages and
currents, reflected power as well as of the exhaust air temperature.
Output RF Arc Protection
An output RF Arc protection is employed. This important feature safeguards
the amplifier, antenna, antenna selector, and tuner against severe damage in
case of possible breakdown.
Continuous Monitoring
Continuous monitoring and/or selectable measurement of the 12 most
important parameters of the amplifier, exciter, and the selected antenna via
OLED display.
Easy Maintenance
Data (service information) regarding amplifier internal status is stored in
a nonvolatile memory for 7 of the most recent auto protection trips.
FAQ
-
Q: Does the amplifier require a separate antenna tuner?
A: No, heavy outboard antenna tuners are not required for antenna SWR up to 3:1. -
Q: What is the power output of the amplifier?
A: The amplifier has a power output of 1500 W PEP or continuous carrier, with no mode limit. -
Q: How many antenna outputs are available on the amplifier?
A: The amplifier has three selectable antenna outputs using a push button on the front panel.
MAIN FEATURES
EASY TO OPERATE
The plate-load True Resistance Indicator (TRI) is a powerful tuning aid which,
together with the automatically controlled input attenuator, helps the
operator to quickly and precisely match the antenna impedance to the optimum
tube load impedance (5‑10 seconds typically). The AUTO‑OPERATE function (when
enabled) maintains the amplifier in OPERATE mode for you, thus saving manual
operations and time.
USER-FRIENDLY AND DURABLE
An amplifier that is both user‑friendly, and that looks after itself. It is
designed to safely withstand up to 400 W reflected power, up to 100
milliseconds duration of drive spikes, drive RF “tails” after a PTT or KEY
release, operator’s inadvertent tuning errors, etc. The amplifier would also
not cease to function with a “soft” AC mains and would deliver more than half
power at only 85% of nominal mains voltage. It would withstand up to 10
milliseconds (down to zero) voltage drops, and up to +15% line voltage spikes,
which is important particularly when used at Field Days, DXpeditions, and
other portable operating events where emergency power is relied upon.
OLED COMMENT DISPLAY
All amplifier status indications are explained via detailed text displayed on
the high brightness and contrast OLED display. The upper‑line’s strip on the
display always reads peak forward power. LED indicators are provided for
OPERATE mode, attenuation‑on, transmit, selected antenna output, and ON/OFF
conditions.
NO ANTENNA TUNER NEEDED
No heavy outboard antenna tuners required for antenna SWR up to 3:1 (and
higher on some bands). Your amplifier will enable you to change antennas
virtually instantaneously and allow you to use your antennas over wider
frequency ranges.
THREE ANTENNA OUTPUTS
Three antenna outputs are selectable using a push‑ button on the front panel.
BROADBAND INPUT MATCHING
Resulting in a very good load to the transceiver over the entire spectrum from
1.8 MHz up to 54 MHz.
LESS NOISE IN THE SHACK
The input bypassing and the vacuum antenna relays are virtually silent even in
the CW QSK mode thanks to specially designed mounting hardware.
TRANSCEIVER-INDEPENDENT
The amplifier operates without special signals from the transceiver ‑ “Ground
on TX” and 85 W RF drive power are sufficient.
SINGLE TUBE OPERATION
Uses a ceramic and metal radial beam tetrode with plate dissipation of 1000 W
which is specially designed for class AB1 RF linear amplifier operation.
TUBE PROTECTION
Permanent monitoring and protection of plate and grid voltages and currents,
reflected power as well as of the exhaust air temperature.
OUTPUT RF ARC PROTECTION
An output RF Arc protection is employed. This important feature safeguards the
amplifier, antenna, antenna selector, and tuner against severe damage in case
of possible breakdown.
CONTINUOUS MONITORING
Continuous monitoring and/or selectable measurement of the 12 most important
parameters of the amplifier, exciter, and the selected antenna via OLED
display.
EASY MAINTENANCE
Data (service information) regarding amplifier internal status is stored in a
nonvolatile memory for 7 of the most recent auto protection trips.
ACOM Ltd.
Bulgaria | Bozhurishte 2227
Sofia‑Bozhurishte Industrial Park | 6 Valeri Petrov Str. GPS coordinates:
42.748616о | 23.209801о
info@acom‑bg.com
ACOM and the ACOM logo are registered trademarks of ACOM Ltd. in many
countries, including the EU and United States. I The used images are
illustrative only.
Subject to change without notice. I Printed in Bulgaria.
All rights reserved. I Design and content by ACOM Ltd.
ACOM 06AT Brochure I Third Edition, Revision 02 I July 2022.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>