Quamtum 2A3WD-CONNECT2 High Performance 5G Indoor Data Terminal User Manual
- August 30, 2024
- Quamtum
Table of Contents
2A3WD-CONNECT2 High Performance 5G Indoor Data Terminal
Specifications
- Wired network port: Support 1000Mbps RJ45 network port
- Power:
- Input: AC 100V~240V, 50Hz~60Hz
- Output: DC 12V/1.5A
- Operating temperature: 0~ +45
- Relative humidity: 5%~95%
- Dimensions: L90 x W50 x H163 (mm)
- Weight: about 415g
Installation Instructions
-
Take out the wireless data terminal and install the SIM card
into the card slot according to the direction marked on the data
terminal. -
Use a standard RJ45 network cable to connect the LAN port of
the data terminal to the computer. -
Use the power adapter to connect the external power
socket.
Attention:
- Do not install the SIM card with power on.
- When handling the SIM card, do not touch the metal.
About Data Terminal
This data terminal can operate under 4G (LTE) / 5G (NR) network,
allowing you to connect to the Internet through WiFi or network
port.
3.1 Interface Description
| Interface Type | Definition | Description |
|---|---|---|
| DC | Power connector | Used to connect the matching power adapter. |
3.2 Indicator Light
Indicator Signal:
Access To The Internet
The data terminal supports RJ45 standard network cable or WiFi
connection to the computer without any driver. Support Windows XP,
Windows 7, Windows 8, MAC OS, Linux, Android, and other operating
systems.
FAQ
Q: Can I use this product in a commercial setting?
A: Yes, the Quamtum Connect 2 is applicable to domestic or
commercial scenarios where communication networks and WiFi hotspots
need to be rapidly deployed.
Quamtum Connect 2 User Manual
V1.0
Thank you for choosing our 5G wireless data terminal products. In order to
enable you to better use the data terminal, please read this manual carefully,
and keep it on standby for future use.
Our company reserves the right to modify the technical parameters and
specifications of this manual, and we will timely improve the printing errors
and discrepancies with the latest data of this manual. All changes will not be
notified in advance, and the Company reserves the right of final
interpretation.
Quamtum Connect 2 is a high-performance 5G indoor data terminal, which
supports NR (SA&NSA) and LTE, converts cellular network data into WiFi and
wired network interface data, supports one gigabit LAN interface, and one
telephone interface, and 2.4G+5G dual band WiFi hotspot (AP). It is applicable
to domestic or commercial scenarios where communication networks and WiFi
hotspots need to be rapidly deployed.
1. Main technical indicators of product
Wired network portSupport 1000Mbps RJ45 network port Power:input : AC
100V~240V, 50Hz~60Hz
output : DC 12V/1.5A Operating temperature: 0~ +45 Relative humidity: 5%~95%
Dimensions: L90 x W50 x H163 (mm) Weight: about 415g
2. Installation instructions
1 Take out the wireless data terminal and install the SIM card into the card
slot according to the direction marked on the data terminal.
2 Use a standard RJ45 network cable to connect the LAN port of the data
terminal to the computer.
3 Use the power adapter to connect the external power socket
and the data terminal, and the data terminal will automatically turn on when
power on. After about 1~2 minutes, the data terminal completes initialization.
4 Place the data terminal on a flat surface. 5 The WiFi function is enabled by
default. You can use mobile phones, tablets and other devices with wireless
connection functions to connect to the data terminal. The default SSID and
WiFi password information for wireless connection can be obtained from the
nameplate at the bottom of the data terminal.
Attention 1) Do not install the SIM card with power on. 2) When handling the
SIM card, do not touch the metal
contact surface to avoid damage to the card by static electricity. 3) The
operating temperature range of this product is 0~45; please do not operate
beyond this temperature range. 4) Please use the adapter specified by this
product to prevent abnormal operation of the machine. 5) This device meets the
EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the
general public to electromagnetic fields by way of health protection. The
device complies with RF specifications when the device is used at 20 cm from
your body.
3. About Data Terminal
This data terminal can operate under 4G (LTE) / 5G (NR) network, allowing you
to connect to the Internet through WiFi or network port.
3.1 Interface Description
Interface Type DC
RST
Figure 1 Interface Diagram
Definition
Description
Power connector
Reset button
Used to connect the matching power adapter.
Used to reset the device to factory settings. working on equipment In this
state: press and hold for 6 seconds, the device will restore the factory
settings.
TYPE-C LAN
SIM Card
Debug interface
LAN port
SIM card interface
Used for device debug log output.
It is used to connect to the network port of a computer or other equipment.
Used to insert SIM card.
TEL
Telephone interface
Connect to the phone for call function
Note: The debugging interface cannot be used for power supply, please use the
factory matching power adapter for power supply.
3.2 Indicator Light
Figure 2 Indicator lights
Indicator Signal 4G
State Green Blue Red Red light flashing Light off Blue
Description Good signal quality Medium signal quality Poor signal quality
SIM card not detected
No signals 4G registered network
5G WiFi POWER
Light off Blue
Light off Blue
Light off
Blue
Light off
4G unregistered network 5G registered network 5G unregistered network WiFi open WiFi not open The external power is normal, and the data terminal is turned on The external power is abnormal, and the data terminal is shut down
4. Access To The Internet
The data terminal supports RJ45 standard network cable or WiFi connection to
the computer without any driver. Support Windows XP, Windows 7, Windows 8, MAC
OS, Linux, Android and other operating systems.
4.1 Data Terminal Preparation Before accessing the internet, please check the
following
options: Whether the SIM card is valid and has been correctly inserted into
the data terminal, and whether it can be recognized normally. The power light
is on. The signal indicator light is on, showing green, and showing blue or
red when the signal is weak. The 4G or 5G indicator lights up and turns Blue.
4.2 Connect Computer The data terminal and computer can be connected through a
standard RJ45 network cable or WiFi. When connecting via WiFi, please refer to
the nameplate on the bottom of the data terminal for SSID and WiFi password
information. The SSID and WiFi password of each data terminal are unique.
Regardless of the connection method, ensure that the computer’s IP address
acquisition method is set to “obtain an IP address automatically”.
4.3 Log in to the data terminal After the computer obtains the IP address,
enter user name and
password found at the bottom of the device to access the data terminal
configuration page, which is the web management page. The factory default user
name and password for the data terminal can also be obtained from the
information provided at the bottom of the device.
5. Configure Data Terminal
When configuring the data terminal, please make sure that the data terminal is working normally and the computer is connected to
the data terminal. Then log in to the web management page to
configure. Please carefully configure some parameters on the web
management page according to the operator’s recommendations.
Improper configuration may result in inability to access the Internet.
Primary menu
Secondary menu
Operational instructions
You can check WAN wireless
WAN Information
information,network parameters,signal strength,APN information and neighborhood
information.
System Status
DHCP Information
2.4G WiFi Information
View the DHCP status and list of connected devices on the LAN side. View 2.4G WiFi network information and user information.
5G WiFi Information
View 5G WiFi network information and user information.
Device
View device running status,
Information memory usage, etc.
Internet
Network
Set the network mode and
Function
Setting
configure network:flight
APN Settings
SIM Function Traffic Setting
Network Acceleration
mode,data switch and data roaming. Set the access name when dialing. This item
needs to be set according to the requirements of the operator. Changing it may
cause the terminal to not work normally.
Set a PIN code.
Enable traffic restriction.
Enable network acceleration and edit special port exclusion list.
2.4G WiFi Settings
You can turn on/off the WiFi function, view/change WiFi SSID, password, encryption method, etc. Users can modify the SSID, password and encryption method of the data terminal WiFi here.
WiFi Settings
2.4G WiFi Advance Settings
5G WiFi Settings
You can set the WiFi TX power, channel, WiFi mode,bandwidth, and maximum
number of connected users.
You can turn on/off the WiFi function, view/change WiFi SSID, password,
encryption method, etc. Users can modify the SSID, password and encryption
method of the data terminal WiFi here.
Device Settings
Firewall
Management
5G WiFi Advance Settings
DHCP Settings
Route Settings VPN Settings
DMZ Port Forwarding
Filtering Rules
URL Filter IP MAC Binding DDOS
Protection
System Settings
Intelligent Setting
System Log
You can set the WiFi TX power, channel, WiFi mode,bandwidth, and maximum
number of connected users. Set IP address management on the LAN side. Design
parameters such as static routing.
Enable and configure the VPN.
Enable DMZ.
Set port forwarding.
Port filtering: set the port number to be filtered. IP address filtering: set
the IP address to be filtered. MAC address filtering: set the MAC address to
be filtered. Set the website addresses that need to be filtered. Set binding
IP and MAC address.
Enable DDOS protection.
Modify password: modify the password for logging in to the terminal
configuration page. Time setting: set the terminal system time. Restore
factory settings: restore the terminal to factory settings.
Intelligent Restart: customize the restart time.
System debugging information
System Upgrade Network
Tools
Reboot
for professionals to view. Upgrading system. ping,trace function. Terminal can be restarted.
FCC ID: 2A3WD-CONNECT2
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: –Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver. –Connect the
equipment into an outlet on a circuit
different from that to which the receiver is connected. –Consult the dealer or
an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provided with antenna
installation instructions and consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s authority to operate the equipment.