dals DCP-LNPD48 RGB Plus CCT Smart Boulevard Pendant Installation Guide
- August 30, 2024
- dals
Table of Contents
dals DCP-LNPD48 RGB Plus CCT Smart Boulevard Pendant
ITEMS INCLUDED IN THE BOX
- LED recessed light
- Junction box
- Mounting hardware
Installation guide for gypsum board
BEFORE YOU START
BEFORE STARTING INSTALLATION, SHUT THE LINE FEED POWER OFF USING THE CIRCUIT
BREAKER.
Instructions about the risk of fire, electric shock, or injury to persons.
Installation must be done according to local electrical codes. Installation
should be done by a certified electrician. This class B digital apparatus
complies with Canadian ICES-005. This digital apparatus does not exceed the
Class B limits for radio-noise emissions from digital apparatus as set out in
the Radio Interference Regulations of the Canadian Department of
Communications.
- Cut a hole in the ceiling and prepare supply wires. Install and unshield the line feed wire 6″ (15 cm) and strip wires 5/8″ (1.6 cm).
- Bring supply power to the junction box through the knockout
- Open the lid of the junction box. Use the quick connectors to pair the wires from the mains with the wires from the connection box.
Compress the springs and push the fixture into the opening. It is easier to do one spring at a time.
INSTALLATION OF 2 OR MORE FIXTURES TOGETHER
Unscrew the end caps where both fixtures meet. Slide the mounting bracket into the middle rail of each fixture. Make sure it is properly centered on the joint before tightening the 4 set screws.
Installation guide for suspended Ceiling
- Unscrew the butterfly nut at the back of the fixture to remove the spring clips.
- A) CENTERED/OFFSET INSTALLATION: Create a 2″ opening in the panel.
- B) PERIMETER INSTALLATION: Remove 2″ from the side of the panel.
- C) INSTALLATION ON RAILS: Plan adding 2 rails spaced 2-1/4″ apart. Cut the panel consequently. BOTH LNR24 AND LNR48 FIXTURES CANNOT BE INSTALLED ON A SINGLE PANEL.
- Insert the linear fixture inside the suspended ceiling and let it rest on the rails. Finally, put the suspended ceiling panel back.
TIPS
It is also possible to only add one rail and use the existing frame as shown
in the example beside.
FCC STATEMENT
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is radio or television rece encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with the Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with FCC/ISEDC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>