EYTSE TC-7009 Stage Lights User Manual

EYTSE TC-7009 Stage Lights

Important Information

This product manual contains important information about the safe installation and use of this equipment. Please read and follow these instructions carefully and keep this manual in a safe place for future reference

What are included

1. Stage lights
2. User manual
3. power cable
4. handle holder
5. Fixing screws

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.

Safety Instructions

Please read these instructions carefully, which includes important information about the installation, usage and maintenance.

• Please keep this User Guide for future consultation. If you sell the unit to another
  user, be sure that they also receive this instruction booklet.

• Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on decal or rear panel of the fixture.

• This product is intended for indoor use only!

• To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked.

• Always disconnect from power source before servicing or replacing lamp or fuse and be sure to replace with same lamp source.

• In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.

• Don’t connect the device to a dimmer pack.

• Make sure power cord is never crimped or damaged.

• Never disconnect power cord by pulling or tugging on the cord.

• Do not operate this device under 113°F ambient temperature conditions.

product information

1. Working voltage: AC100V-240V 50/60Hz
2. Power consumption :15W
3. LED light source :3*2W
4. Laser light source :532nm green laser emitter 650um red laser transmitter
5. Avsilsbility environment: 50~86℉ indoor
6. Prebesting time: 2-8min（When the temperature is below 50℉）
7. Working mode : DMX512, Manual， Remote control

Rear Panel

Menu Button Function

two digits indicate the S1 mode, and the last two indicate the data jump detected by the sound.
10| | Corresponding remote control MUSIC2 (Sound activated mode 2),The first two digits indicate the S1 mode, and the last two indicate the data jump detected by the sound.
11| | Corresponding remote control MUSIC3 (Sound activated mode 3), The first two digits indicate the S1 mode, and the last two indicate the data jump detected by the sound.
12| | Corresponding remote control FLASH (Flash mode）

Remote Control Function

Introduction to remote control function

ON/OFF

| ON/OFF

LED

| LED ON

LASER

| LASER ON

A1

| Laser dithering pattern changing, LED slow color conversion

A2

| The LED turns to change color, and the laser lights up for a long time and changes the picture slowly

A3

| Laser alternating pattern, LED slow color conversion

A4

| Laser alternating jitter + positive and negative conversion diagram, LED slow conversion color

A5

| Laser long light fast + positive and negative conversion diagram, LED stroboscopic color change
Music1| Closed light voice control: silent and not bright, with sound, laser and LED color changing and flashing
---|---
Music2| Dynamic voice control: silent self-propelled, with sound, laser and LED fast color change
Stroboscopic voice control: the silent motor stops, and the laser and LED are fixed in a certain mode;
The sound motor rotates, the LED flashes and changes color, and the laser changes color quickly
FLASH| Stroboscopic: laser and LED stroboscopic

DMX Control: (Press MENU choice d001)

Master and slave settings: (Press MENU choice d001)

Two or more of the same lamps are connected by network cable. Set any one as the host and other lamps as the slave; When the host working mode is adjusted, the slave automatically works with the host mode.

Note: All lights are in the slave when taking signal from console and no light can in Master.

Security matters

The product is a class II R laser product, so you should avoid the eye close to the hole position by the laser irradiation or may cause eye discomfort.
Do not allow children to operate the product alone, or other people before the operation, please check the safety tips.
This product is suitable for indoor use, and its protection grade is IP20. It is ideal for a dry environment. Please avoid using it in humid, overheated, and dusty environments. Keep good heat dissipation around the product and avoid flammable objects or liquids.
Please use the power supply line provided by the company to supply power to the product. If you need to replace the power supply line, please refer to the parameters of the original power supply line to select the qualified power supply line. If you need to extend the power supply line, please use a diameter sufficiently qualified wire, and control the extension length to prevent line loss if the power line load is too high.

Customer Support

*If you have any questions please contact: www.eytse.com
Email: customer@eytse.com

References

• Surfaces.be
• EYTSE - Shop Koraoke, Stage lights,Amplifiers, and Electronic organs – Eytse

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>