EYTSE EY001-L Stage Laser Light User Manual
- August 24, 2024
- EYTSE
Table of Contents
EYTSE EY001-L Stage Laser Light
Product Information
Specifications
- Compliance: Part 15 of FCC Rules
- Conditions: Must not cause harmful interference; must accept any received interference
Product Usage Instructions
Installation
- Ensure the receiving antenna is properly oriented.
- Maintain adequate separation between the equipment and receiver.
- Plug the equipment into an outlet on a different circuit from the receiver.
- If facing issues, consult the dealer or a qualified radio/TV technician for assistance.
Modifications
Any changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment. It is important to adhere to approved modifications only.
Compliance
Ensure compliance with Part 15 of the FCC Rules. Operation should adhere to the conditions specified, including avoiding harmful interference and accepting any received interference.
FAQ
Q: What should I do if I experience interference issues?
A: You can try reorienting the antenna, increasing separation, or consulting a professional for further assistance.
Q: Can I make modifications to the device?
A: Only approved modifications should be made to avoid voiding the user’s authority to operate the equipment.
Remote control instructions
Product parameter
Menu
Debug channel list
If you have any questions please contact us :
Email: customer@eytse.com
Security matters
The product is a class IIIB laser product, and should avoid the eyes close to
the hole position by the laser irradiation, or may cause eye discomfort.
Do not allow children to operate the product alone, other people before the
operation, please check the safety tips This product is suitable for indoor
use, and its protection level is IP20. Apply to dry conditions, please avoid
use in wet, hot, dusty environment. Products should maintain good heat
dissipation, away from flammable objects or liquids.
LightElf (WeChat Mini Program & Android App) User Manual
Software installation (WeChat mini program / Android APP)
( You need to grant the software permission to access Bluetooth and
positioning, otherwise it cannot be used normally. )
WeChat mini program:
Open WeChat, search for in the mini program or scan the QR code below to use
it
Android App
APP Download address: www.eytse.com Or log in to the
Google Play Store and search for “LightElf” to install it
- The main interface after the software is started is as shown in the figure
Connect laser light equipment
- Please tum on the laser light equipment before use
- Open the software and click “Click Me To Connect” on the main interface.
- Select Laser_Llght_xxxx in the Bluetooth list
- Successfully connected to device
Software settings
- The address code, display range and XY related parameters of the laser light device can be set
- The menu language of the software can be changed at the bottom
Turn the laser on and off
Click the switch button on the right side of the main interface. After turning
it on, the words “Device ON” will be displayed.
Click the switch button on the right side of the main interface. After
closing, the words “Device OFF” will be displayed.
Introduction to hand-drawn graffiti function
Click the hand-drawn graffiti menu in the main interface to enter. Here you
can control the display effect of the device by manually drawln1 patterns,
enterln1 text, or selectln1 bullt-ln patterns.
- Selection of color: The upper part of the interface is the color selection area. Click the different color buttons to select the color of the laser drawing.
- Draw patterns: The middle part of the interface is the pattern control area. In this area you can do the following operations
Manually draw patterns
- Click the icon to switch to the manual pattern drawing function
- Use your finger to draw the pattern you want on the middle large screen area
- You can also click the icon make drawing easier to add a picture background to make drawing easier.
Text Input
-
- Click the icon to swit.ch to text input function
- Enter text in the input box
- Use your finger to drag and drop in the middle of the screen
- You can also choose different fonts on the left side of the input box (Note: The font library of the mini program version is limited, and some texts or symbols may not be included. If you need a more complete font library, it is recommended to choose the app version)
Select the built-in pattern
- Swipe the pattern list to view all built-in patterns
- Click on the pattern and drag it with your finger in the middle of the screen
Graphic operation and parameter configuration
-
The clear and back buttons can be used to delete the drawn pattern.
After deletion, the pattern can be redrawn. -
Click the configuration button to configure parameters, configure the size, rotation angle, flip, and horizontal and vertical movement of the graphics.
Click on the left side to select the parameters to be configured, slide up and down on the right side to change the parameter value, and click the OK button to save the parameters. -
After the pattern is drawn, click the send button to display the pattern effect on the device.
Introduction to text playback function
Click the text playback menu in the main interface to enter. Here you can set
the text display effect, which can support up to 50 characters.
- The upper part is the color selection area. Click the corresponding button to select the color of the text
- The middle part sets the area for text
- Click on the left to select a font
- In the middle is the text input box
- The number on the left side of the text input box indicates the current text group
- Click the “+” on the right side of the input box to add a new text group. Up to 4 groups are supported.
- Click the playback duration of the group to modify the time
- After completing the text Input, click the preview button In the lower-left corner to generate a preview effect in the middle of the screen.
- Click the send button to display text effects on your device
- There are three configuration parameters in the following section
- Text size: Adjust text size to change the size of text displayed on your device
- Display viewing distance: adjust the size of the display area (use to adjust the projection distance)
- Water flow speed: Adjust the water flow speed to change the speed at which text moves from left to right. When set to 0, the text remains stationary and does not move.
Personalized programming
Click the personalized programming menu in the main interface to enter. By editing the pattern of each scene, the laser ll1ht device can play In sequence according to the programmed scenes to meet your personalized needs. It can support up to 20 scene editing.
A, Scene management
- Click the New Scene button at the bottom of the page to add a new scene
- Click the delete icon on the left in the scene list to delete the scene
- Click the number on the right in the scene list to modify the playback duration of the scene.
- Click the corresponding edit button in the scene list to enter the scene editing page
Scene editing
- Click the Select Graphics button at the top of the page to pop up a selection Interface for various graphics, with a total of 7 groups including dynamic graphics. CIiek on a graphic to see the effect of the graphic in real-time on the device. After selecting, click the OK button to save.
- You can also select graphics by modifying the channel parameters below, select graphics groups or graphics In the channel menu on the left, and slide up and down on the right skateboard to select
- In addition to graphic selection, you can also set different display effects. Just select the parameters on the left and slide up and down the skateboard on the right.
Built-in program playback
The system has built hundreds of ll1htln1 pr01rams for you to choose from, and
they can be played without any editing clicks. All built-in programs can be
played randomly or specified programs can be played.
A. Random play: all programs are played randomly
- Click on the random play menu in the main interface to enter
- Click the color button above to select the color of the laser
- The playback mode supports two modes: self-propelled and voice-controlled. The slider below can adjust the self-propelled speed and voice-controlled sensitivity.
Line playback,, animation playback Chrisbnas playback outdoor program playback
- Click the corresponding program menu in the main interface to enter
- For the color and play mode settings in the program, please refer to the random play page
- Selecting loop means that the 50 programs under this category will be played in order.
- You can also check the box to play some of the programs and just click to play the program
FCC
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.