Anchorlift WS60C External Thruster Instruction Manual

Anchorlift WS60C External Thruster

Product Specifications

• Model: WS60C
• Power Supply: DC 12-48V
• Recommended Tools: Battery drill, drill bits (2.5mm, 3.5mm, 5mm, 12mm), threading tool, screwdriver, sealant

FAQs

Q: What tools are needed for installation?

A: Tools required include a battery drill, various drill bits, threading tool, screwdriver, and suitable sealant.

Q: Can the motor be run out of water?

A: Avoid running the motor for longer than 5 seconds out of water. Follow specific model instructions for wiring and operation.

Q: What if the motor turns the wrong way?

A: Swap the positions of the brown and blue motor cables to correct the direction.

Instructions

Tools needed for an installation:

Battery drill with different drill bits. 2.5mm – 3.5mm – 5mm – 12mm drill bit. 6mm threading loss. Small flat screwdriver. Tools for electrical work and general hand tools. Polyurethan sealant is suitable for under saltwater use.

• STEP 1 :
  • Find a good location for the motor. It’s important that the motor can make free water flow out from the propeller.
  • Make sure there are no obstacles on the inside so you don’t hit any wires or tubes.
• STEP 2 :
  • Once you have found a good location use the motor bracket, mark the 2 holes for the 6mm mounting bolts.
  • Make sure the bracket is mounted the same way as in the piture, a square point on the bracket pointing out.
  • The bracket you use for marking the holes must be used on the same side.
• STEP 3 :
  • Drill holes for the motor bracket, use 5mm drill bit, then use the 6mm threading loss and make treads in the holes
• STEP 4:
  • Making holes for cable clamp and cable inlet.
  • Plan where you want the cable clamps and the cable inlet.
  • NOTE !! The cable inlet must always be over the water line.
• STEP 5:
  • Drill holes for screws for cable clamp 3,5mm. Cable inlet cover 2,5mm. Hole for motor cable 12-13mm.
  • Remove antifouling where the sealant will be. Note !! The hole for the cable must be angled down so the motor cable will lay flat into the transom.
• STEP 6:
  • Mounting motor bracket, cable clamp, and cable inlet cover.
  • Ad sealant under the bracket, bolt holes, and cable clamp hole,
  • Mount the motor bracket with 2pcs 6x70mm bolt, since the holes have treads you must screw the bolt in.
  • Tighten bolts well, but not too hard so you damage the treads and bracket.
• STEP 7:
  • Mounting motor and cable inlet.
  • Mount the motor on the bracket. Put the cable into the cable hole.
  • Ad sealant on the hole for the cable clamp and around the motor cable. Mount the cable clamp with screw 4,8x19mm
  • Ad sealant on the hole for the cable cover. Before you mount the cable cover have extra sealant on the cable and push
  • the cable in and flat against the transom. Mount the cover with 3pcs 3,5x16mm screws.
• Step 8
  • Ad zink anode
  • Before mounting zink anode ad marine grease in the screw hole on the motor and on the screw.
• Step 9
  • Wiring. NOTE! DO NOT RUN THE MOTOR FOR LONGER THAN 5 SEC WHEN OUT OF WATER.
  • Follow the instructions for your model.
  • WS60C with DC-DC 12-48vdc converter.
  • When replacing your existing bow thruster panel please note if your existing bow thruster is positive or negatively
  • controlled. Contact us if any questions.
  • NOTE! The propeller direction is anti-clockwise when looking at the motor from the propeller side.
  • NOTE! If the motor goes the wrong way, change the position of the motor cable to brown and blue.
  • This instruction is intended as a guideline for an installation, since boats are different it may be your installation
  • be a bit different as shown in this guide. If any questions don’t hesitate to contact us for questions.
  • Anchor lift Technic
  • Oslo Norway
  • Email: sales@anchorlift.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>