ZROADZ Z394951 Rear Spare Tire LED Light Mounts Instruction Manual

: August 17, 2024
: ZROADZ

Z394951 Rear Spare Tire LED Light Mounts

“`html

Product Specifications:

Vehicle Compatibility: 2019-2021 Jeep Wrangler JL
Part Numbers: Z394951 / Z394951-KIT
Product Type: Rear Spare Tire LED Light Mounts
LED Lights:
- Z394951 – No LED Lights Included
- Z394951-KIT – (2) 3 LED Light Bar

Product Usage Instructions:

Before You Begin:

Turn off the engine, chalk tires with stop block, open the hood,
and disconnect the battery. Layout and organize all the provided
parts.

LED Light Bracket Installation:

Tools Required:
– Air Hose & Nozzle
– Alcohol Cleaning Solution
– Cleaning Rag
– Socket Set & Ratchet Tool Ratchet Extensions
– Various Wrenches
– Dikes or Snips
– Torq Bit Set
– Heat Gun

Step 1:

Lay out and organize all the provided parts.

Step 2:

Organize the hardware and LED Pods if included.

Step 3:

At the rear of the vehicle, unlock the tire and remove the
spare.

Step 4:

Unscrew and remove the (4) screws that hold and secure the
middle rear brake light.

Step 5:

Assemble the 3 LED Light Pods to the ZROADZ Mounting Bracket.
Adjust the LEDs in your preferred direction.

Step 6:

Install the assembled ZROADZ Mounting Bracket onto the vehicle’s
middle rear brake light using the removed screws.

Step 7:

Wire up and connect LED Light Pods with a power wiring harness.
Route and hide all power wires discreetly.

Step 8:

Install Spare Tire and Spare Tire Lock in the reverse order it
was removed.

Step 9:

Adjustment Tips:
To adjust the angle of your LED Lights, rotate the LEDs till your
desired light pattern is reached. Avoid over-tightening the
mounting hardware.

Frequently Asked Questions (FAQ):

Q: Do I need professional installation for this product?

A: Professional installation is recommended for optimal results,
but detailed instructions are provided for self-installation.

Q: How do I verify fitment before starting the installation

process?

A: Contact our tech department at orders@zroadz.com to verify
fitment and get assistance with any technical questions.

“`

PROFESSIONAL INSTALL RECOMMENDED 2019-2021 JEEP WRANGLER JL
PART#: Z394951 / Z394951-KIT
REAR SPARE TIRE LED LIGHT MOUNTS

Parts included

Installation Guide

– (1) Rear Spare Tire Mounting Bracket
LED LIGHTS included
Z394951 – No LED Lights Included Z394951-KIT – (2) 3″ LED Light Bar
– (1) Power Cable Wiring Harness

START HERE
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE INSTALLATION. Auto makers offer varied models to each vehicle and occasionally manufacture more than one body style of the same model. To assure your part is correct; our tech department can be contacted at orders@zroadz.com to verify fitment and assist with technical questions. All other inquires can be directed to orders@zroadz.com. In the event you do not have internet access please call 844-653-8040

APPLICATION MODELS VARY. WE RECOMMEND TO VERIFY FITMENT BEFORE BEGINNING INSTALLATION PROCESS. * IMAGES FEATURED IN THE INSTRUCTION DOCUMENTS MAY NOT ALWAYS EXACTLY MATCH YOUR MODEL OR PART.

BEFORE YOU BEGIN

LED LIGHT BRACKET INSTALLATION

hardware included

START HERE: Turn off engine, chalk tires with stop block, open the hood and disconnect the battery. Layout and organize all the provided parts.

(2) – Stainless Steel M8 x 20 Hex Head Screws (2) – Stainless Steel M8 Split Lock Washers (2) – Stainless Steel M8 Hex Nuts (2) – M6-1.0 Extruded “U” Nuts

STEP 1 1) Lay out and all the provided parts.

FIG 1

Tools Required

– Air Hose & Nozzle – Alcohol Cleaning Solution – Cleaning Rag

– Socket Set & Ratchet Tool Ratchet Extensions
– Various Wrenches – Dikes or Snips – Torq Bit Set – Heat Gun

STEP 2
2) Organize the hardware and LED Pods if you have them.

Page 1

FIG 2

SEE FIGURE 2

LED Light Bracket Installation – Continued

STEP 3

SEE FIGURE 3

At the rear of the vehicle, unlock the tire and remove the spare.

FIG 3

STEP 4

SEE FIGURE 4

Unscrew and remove the (4) Screws that hold and secure the middle rear brake light as seen in Figure #4.

FIG 4

STEP 5

SEE FIGURES 5 & 6

Assemble the 3″ LED Light Pods to the ZROADZ Mounting Bracket as seen in the Figures #5 & #6. The Pods are fully adjustable so point the LED in your preferred direction; Up / Down / to the Side away from Spare tire / etc.

FIG 5

FIG 6

LED Light Bracket Installation – Continued

Page 2

LED Light Bracket Installation – Continued

STEP 6

SEE FIGURE 7

Install the assembled ZROADZ Mounting Bracket onto the Vehicle’s middle rear brake light as seen in the Figure #7.
Use the screws that were removed in Step #4.

FIG 7

STEP 7

SEE FIGURE 4

At this point, it is recommended to wire up and connect LED Light Pods with a power wiring harness.

Route and hide all power wires to be hidden and discreet.

ZROADZ recommends LED Lights be wired with ZROADZ harness kit (part# Z390020D- 25A ) or by utilizing a compatible custom wiring harness. Wiring must be installed by competent & knowledgable automotive electrician.

STEP 8

SEE FIGURE 7

Install Spare Tire and Spare Tire Lock in the reverse order it was removed.

FIG 8

STEP 9

ADJUSTMENT TIPS

To adjust the angle of your LED Lights, rotate the LED(s) to adjust the angles till your desired light pattern is reached. There will be minimal adjustment due to curved light bar orientation. You may than tighten the hardware and secure everything into place. Be careful not to over tighten the mounting hardware.

It is best to adjust the angle with the vehicle on level ground with lights facing a wall, garage door or other solid barrier. We recommend checking from a distance of 25′. Your installation is now completed.

FIG 9

LED Light Bracket Installation – Complete
FIG 10
Page 3

zroadz PRODUCT WARRANTY

ZROADZ PRODUCT WARRANTY
ZROADZ warrants its grille products to be free from defects in material and workmanship for the lifetime of the grille. ZROADZ warrants the finish of its grille products for a 3 year period beginning at the time of sale to the end user. These warranties are limited warranties and do not cover abuse, modification or improper installation nor do they cover finish failure caused by caustic cleaning agents, road salts or other chemicals. ZROADZ reserves the right to repair or replace a defective product at its sole discretion. Any ZROADZ product must be returned to ZROADZ for warranty consideration and must be returned at the customer’s expense. In the event that the product is deemed to be defective, the repaired or replaced item will be returned via a surface shipping method to the customer at ZROADZ expense. No provision is made for any labor, rental car or other costs incurred by the failure of its products.
LED Lighting Equipment Installation / Disclaimer
WARNING
PLEASE CONSULT YOUR LOCAL AUTOMOTIVE ELECTRICAL PROFESSIONAL FOR INSTALLATION SERVICES AND ADVICE. ZROADZ IS ONLY EQUIPPED TO PROVIDE BASIC TECHNICAL ASSISTANCE DUE TO THE DIVERSITY OF VEHICLES, VEHICLE OPTIONS & MODIFICATIONS AND LIGHTING CONFIGURATION OPTIONS AVAILABLE. ZROADZ cannot be held liable due to improper component installation and / or faulty wiring.

GENERAL GUIDELINES
LED Lights & LED Light Bars operate at relatively high currents and should only be installed by qualified personnel with experience in switched / relayed high draw DC Circuits.

–

Light Bars are designed for use only with standard 12v DC power systems

–

Light Bars are for OFF-ROAD USE ONLY. Check your local laws & regulations regarding vehicle mounted lights.

–

Some Light Bars are equipped with waterproof connectors while others are simply pig-tailed

–

Red Wires = POSITIVE | Black Wires = NEGATIVE

–

ALWAYS install your lights on a fused circuit. Basic fusing guidelines: maximum 5A for every 10″ of LED Light Bar.

GENERAL USE, INSTALL AND ADJUSTMENT TIPS
NOTE 1: ZROADZ LED Light Bars themselves are for OFF-ROAD USE ONLY. NOTE 2: Light Bars depending on the configuration of your vehicle and its options and/or modifications may need to be adjusted for appropriate beam projection. To adjust the angle of your light bars simply loosen the mounting hardware on either side of each Light Bar, rotate the Light Bar to adjust the angle, then tighten the hardware once the desired angle is achieved (please be careful not to over-tighten the mounting hardware or scratch the protective powder-coat finish). It is best to adjust the angle with the vehicle on level ground with the lights facing a wall, garage door or other solid barrier at a distance of approximately 25-30 feet.

NOTE 3: Please consult a qualified automotive electrical professional for light bar wiring installation. NOTE 4: An optional universalPRwaersirteisrnvagerdehaP-rACnToeEpsNsyTr(ipgPahErtNt#©D2ZIN0319G50.0 -A2Zl0lRSRO-iAAg)hDitZss.aclosmo available that includes high-heat & oil/fuel resistant wires, waterproof connector, 12v relay, 12v rocker switch, inline fuse holder. Our universal wiring harness significantly expedites the installation process but is not a vehicles specific “Plug & Play” product and does not eliminate the need for a professional installation.

Please contact your local ZROADZ dealer for more information or visit www.zroadz.com.

PRODUCT Care Information

PRODUCT CARE INFORMATION Wash regularly as you would when caring for your vehicles. Never use dish soap. Never leave wet water spots as that may leave a blemish.
MATTE BLACK FINISH Paint warranty applies to defects in material and / or workmanship, it does not cover the matte finish surface appearance. To enjoy the matte appearance for many years to come, please follow these owner care and maintenance tips. Get a no-shine matte car wash soap that uses no fillers, no silicone, and won’t strip your matte paint of its layer of protection.
Do not use wax, detail spray, armorall®, or any products made for normal paint. Use only products specifically developed for matte finish paint. Do not use products that are even mildly abrasive, such as polishes, glazes, or rubbing compounds. Do not use mechanical cleaners or polishers. Do not use terrycloth, cloth, or paper towels. Do not rub the finish vigorously, this will burnish the paint finish, causing a permanent shiny spot. Shiny spots cannot be removed.
Do not use commercial car wash facilities or their shine enhancement products. Most car wash brushes, large mechanized “towels,” and shine enhancement products can damage matte paint.
Remove foreign substances such as insect remains, tar, and road debris using a soft applicator and a mild solvent; saturate and soak area before cleaning–rub lightly.
Hand-wash with a soft wash mitt and mild cleaning product safe for matte paint. Use microfiber cleaning cloths with alcohol-based window cleaner for basic surface clean-up.
GLOSS BLACK FINISH ZROADZwith Gloss Black Powder Coated Finish may be washed regularly as you would when caring for your vehicles finish using soap and water. ZROADZshould be waxed at the same time that you wax the vehicle. As a general rule, anything you use to clean your vehicles painted surfaces can be used to clean and maintain your ZROADZ grille. A Gloss powder Coated Finish can be cared for in the same fashion that you would care for your vehicles factory paint job. Never leave wet water spots as that may leave a blemish.