MARSHALLTOWN WL793 20 Inch EZ Flooring Shear

Product Specifications

• Model: EZ Shear 20
• Manufacturer: MARSHALLTOWN
• Website:www.MARSHALLTOWN.com

Product Usage Instructions

Assembly

1. Ensure all parts are visible.
2. Tools needed for assembly: A, H, I, J, M, K, L, B, C, D, E, F, G
3. Attach the handle (G) to the handle assembly (F).

Cutting Instructions

1. While gently pushing down, pull the safety pin and lift the handle.
2. Place the product on the table. It is recommended to HOLD THE MATERIAL IN PLACE until the cut is completed. Lower the handle until the blade touches the material.

Maintenance

• Sharpening the blade:
  • Use a Phillips screwdriver to replace and tighten the screws, starting with the central screw.

Frequently Asked Questions

Q: What should I do if the blade gets stuck after cuts?

A: Verify the blade stops, remove and tighten them. Also, check if there are marks on the anvil indicating wear from overlapping.

Q: How can I ensure smooth and accurate cuts?

A: Inspect and lubricate the bearings/pins of the material.
Check for any oblong/displaced holes in the pins and adjust the front travel stop if using MAGNUM cutters.

INTRODUCTION

• Thank you for your purchase of the Bullet by MARSHALLTOWN EZ Shear Flooring Shear.
• This versatile, light-duty flooring shear is proudly Made in the USA, manufactured with the highest-grade materials, and designed with the flooring professional in mind.

Your new EZ Shear Flooring Shear includes features such as:

• Easy and quiet one-cut action
• Ability to cut inside without dust, noise, or electrical cords
• Built-in ruler for accurate cuts
• A strong, lightweight aircraft-grade aluminum construction
• Handhold for easy transportation
• Metal jacketed bearings for long tool life
• Moveable fence for 45 and 90-degree cuts

And can cut materials up to ⅔6″ (14mm) thick, 20° (508mm) wide, including:

• Engineered Hardwood Flooring (up to /5 / 12mm thick and 1250 Janka – ONLY cut by flipping material over with the back facing up)
• Laminate flooring
• LVP/LVT/VCT
• PVC & Rubber Tile
• Cove Base
• WPC/MLF/SPC|
• Carpet Tile
• Rigid Core
• This owner’s manual provides the information needed to operate and maintain this EZ Shear Flooring Shear.
• Carefully read and follow all safety and operating instructions in this manual. Ensure every operator of this flooring shear reads this manual before operating the unit.
• The replacement of any part on this flooring shear other than the manufacturer’s authorized replacement part may adversely affect the performance, durability, or safety of the product.
• Be sure safety precautions are observed. Read and follow all safety and operating instructions in this operator’s manual.
• The manufacturer reserves the right to make changes to or add improvements to its product at any time without prior notice or obligation.
• The manufacturer reserves the right to decide, upon its sole discretion and at any time, to discontinue this product.
• This manual covers the EZ Shear Flooring Shear. For technical questions or repair parts, please call MARSHALLTOWN customer service at 1-800-888-0127 or visit www.MARSHALLTOWN.com.

SAFETY PRECAUTIONS

• DANGER or WARNING safety signs are located near specific hazards. DANGER! WARNING!
• General precautions are listed on CAUTION safety signs.
• This notation appears before warnings in the text. It means that the step that follows must be carried out to avoid the possibility of personal injury or death.
• These warnings are intended to help the technician avoid any potential hazards encountered in the normal service procedures. We strongly recommend that the reader take advantage of the information provided to prevent personal injury or injury to others.
• THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING CERTAIN PRECAUTIONS.
• READ AND TAKE THE FOLLOWING PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP PREVENT ACCIDENTS. EQUIPMENT SHOULD BE OPERATED ONLY BY THOSE WHO ARE RESPONSIBLE AND INSTRUCTED TO DO SO.
• CALIFORNIA PROPOSITION   65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
• NEVER operate the flooring shear if any shear components have been removed.
• Keep inexperienced and unauthorized people away from the flooring shear at all times.
• Keep the flooring shear in good operational condition. Loose or damaged parts are dangerous.
• Avoid loose clothing that could get caught in moving parts.
• Keep hands and feet away from moving parts.
• Keep all warning, caution, and safety instruction labels in good condition. Replace missing, damaged, or illegible labels.
• Clear the work area around the shear to prevent tripping or falling onto the shear.
• Operate on level ground to prevent the flooring shear from flipping over.
• DO NOT OPERATE this flooring shear under the influence of alcohol or while taking medication that impairs your reactions.
• Use only factory-authorized parts for replacement.
• Wear safety glasses when operating the flooring shear.
• Always use caution when replacing the shear blade.
• Only operate the shear with the approved materials. If extreme force is required to cut a material, it may result in personal injury and/or damage to the flooring shear.
• Wear proper protective clothing while operating flooring shear, including eye, ear, and clothing.
• Handle all solvents and cleaning agents with care and follow the manufacturer’s instructions on safety and disposal.

SAFETY DECALS

If your safety decals are damaged, they can be replaced by contacting Customer Service.

Blade Warning Label

Handle Warning Label

WARRANTY

• This product is warranted to the original purchaser only, to be free of defects in material and workmanship under normal use, for one year from the purchase date. MARSHALLTOWN shall without charge for parts and labor, repair or replace such parts which are found to be defective. All transportation charges for replacement parts must be borne by the purchaser.
• For warranty service, the product must be delivered, with proof of purchase date, to MARSHALLTOWN. Contact MARSHALLTOWN Customer Service to determine the best method of delivering the product that is under warranty.
• The delivery of the product must be made no later than 30 days after the expiration of the warranty period.
• All implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one year from the date of purchase by the original retail customer, and to the extent permitted by law all implied warranties are excluded and disclaimed after the expiration of such period.
• Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Exclusion from this warranty:

1. All consequential damages, including pickup and delivery of the unit, communication, mileage charges, and/or rental of a replacement unit during repairs are not covered under this warranty, nor are any loss of income and/or other loss resulting from the failure of the product to function due to a warranty defect.
2. This warranty will not apply when the product becomes inoperative due to misuse, normal wear, neglect, improper maintenance, accident, or freight damage; has not been operated and maintained under the instructions furnished in the Operator’s Manual; or has been altered or modified without approval from the factory Service Department.
3. No parts or products are to be returned to the factory without prior written approval from the factory.

ASSEMBLY

1. Lay out all of the parts
   • Tools for Assembly:
   • Electric drill or impact driver with #3 Phillips bit

   • 3 Phillips Screwdriver

   • 2 Phillips Screwdriver

   • ½” or 13mm wrench
   • A. Bed
   • B. Shear Assembly
   • C. Bed Brace
   • D. Leg
   • E. Bed Fence
   • F. Handle Assembly
   • G. Handle
2. Lay out all hardware.
   • H. ¼-14 x 2½ PHPSMS
   • I. M8-1 ¼ x 50 Hex Bolt
   • J. M6-1 x 16 PH PMS
   • K. #10 x ¾ FHPSMS
   • L. M6-1 x 12 FHPMS
   • M. Honing Stone (lx)
3. Attach the Bed Brace (C) and Leg (D) using a Hardware Set (J).
4. Attach the Shear Assembly (B) to the Bed Brace (C) using Hardware Set (H).
5. Attach the Bed (A) to the Shear Assembly (B) using Hardware Set (K) for the back and Hardware Set (L) for the front.
6. Attach the Handle Assembly (F) to the Shear Assembly (B) using Hardware Set (I).
7. Attach the Bed Fence (E) to the Bed(A).
8. Attach the Handle (G) to the Handle Assembly (F).

PRODUCT OPERATION

When most materials are cut, the ‘drop’ piece will have a beveled edge, while the ‘keep’ piece (the piece left on the table) will have a mostly square edge.

1. While gently pushing the handle down, pull the Safety Lock pin out, then lift the handle.
2. Place product on the table. It is recommended that you HOLD YOUR MATERIAL IN PLACE until the cut is complete. Bring the handle down until the blade touches the material.
3. Push the handle down to cut.
   • Some effort may be required depending on the hardness of the material.

SAFETY LOCK

When not in use, slide the Safety Lock pin into the Power Assembly to lock your tool. To remove, gently push the handle down, pull out the Safety Lock pin, then lift the handle.

TRANSPORT

• Always re-engage the Safety Lock pin and secure the extended handle in the down position while storing, carrying, or transporting your shear.

CUTTING GUIDE

• The EZ Shear Flooring Shear is designed to cut a variety of materials. Materials include Engineered Hardwood Flooring (up to½”/ 12mm thick and 1250 Janka-ONLY cut by flipping material over with the back facing up), Laminate Flooring, LVT, LVP, VCT, PVC & Rubber Tile, Cove Base, WPC, SPC, MLF, and Rigid Core.
• Note: DO NOT attempt to cut any solid wood or high-pressure laminate. Additionally, do not cut engineered hardwood with a Janka Hardness Rating higher than 1250, and do not cut engineered hardwood with a Janka Hardness Rating lower than 1250 without first flipping over the material and cutting with the back facing up.
• Note: Even the approved materials may vary greatly in density and hardness. If extreme force is required to cut a material stop immediately, as it could lead to damage to your shear or injury. Attempting to cut unapproved materials will void the warranty.

45 DEGREE CUTS

• Firmly lift the friction-fit fence to remove it from the table and press back down in the appropriate 45-degree position.
• NOTE: This image is for the Marksman. Your shear may look slightly different.

FLOPPY MATERIALS

• When cutting floppy materials, flip the anvil: Remove the anvil and blade-stop using a 4mm or 5/32″ hex key. Reinstall with flat side up instead of bevel.
• This makes fibrous and floppy materials (examples: cove base, thin vinyl plank) cut more easily.
• For Kevlar® fiber reinforced materials (example: rubber belting), put the flat side of the anvil up above, but also remove the plastic blade-stop.

DOUBLE CUTTING

• Most materials shear very well with just one cut. However, some brands of fiber cement siding and other products may require cutting twice to produce a better cut.
• Simply make your first cut 1/a” to¼” (3 to 6mm) longer than your mark, then go back and make your second cut on your mark.
• This is very useful to create a cleaner cut when a trim molding or transition cannot be used to cover your cut end.

MAINTENANCE

Honing the Blade

• Push the handle down until the blade is 1/s” (3mm) above the tabletop. Place the provided Hone Stone against the flat side of the blade. Slide the honing stone from one end of the blade to the other 3-4 times.
• This will remove any burrs from your blade.
• When you first get your shear, you should hone after your 5th cut, then hone your blade every 10th cut for the first 100 cuts until your blade is broken in. From there, you only need to hone once per job.
• Use caution when honing the blade. The blade is sharp and can easily cause injury. Cut-resistant gloves are recommended when honing the blade.
• For more information on honing your blade, scan the QR code or visit www.marshalltown.com/honing-your-blade.

Sharpening the Blade

• The blade can be sharpened to restore a one-sided, 21° – 22° knife edge. It is important to note that the blade must be sharpened only on the beveled side, leaving the flat side flat.
• We recommend that power grinding only be done professionally, as the blade must be fluid-cooled during this process.

Replacing the Blade

WARNING: Blade is extremely sharp! Use cut-resistant gloves when replacing the blade.

1. TURN SHEAR UPSIDE DOWN Tip: put the shear on the edge of a sturdy table.
2. LOOSEN BLADE Using a Phillips screwdriver, remove the screws.
3. REMOVE BLADE Hold the blade by each end and carefully lift it out of the pocket.
4. INSTALL BLADE Hold the blade by each end and carefully place it into the blade pocket in the head, with the flat side of the blade facing the table. Be sure that it is firmly seated, and the pocket is clear of debris.
5. TIGHTEN THE BLADE Using a Phillips screwdriver, replace & tighten the screws, starting with the center screw.

NOTE: This image is for the SharpShooter 2.0. Your shear may look slightly different.

Lubrication

After every 100 cuts, it is recommended that the shear be lubricated. Use a light oil and grease (wheel bearing grease) and apply according to the image below. Lubricating the shear will extend the life of the shear and result in easier cutting.

PARTS BREAKDOWN

REF #                                    DESCRIPTION| EDI| PART#| QTY
---|---|---|---
1                                          EZ 120 FLR TABLE| R7323| CON- TBL-0120| 1
2                                               120 HEAD| R7212| CON-HED-0120| 1
3                                           EZ 120 FLR CAM| R7123| CON- CAM-0120| 1
4                                             120 FLR BASE| R7083| CON- BSE-0120| 1
5                                         EZ %” STROKE PIN| R7234| CON- PIN-0100| 2
6                           1½” SQUARE x 97/s” LOWER HANDLE| R7199| CON- HAN-L200| 1
7                                       EZ SHEAR RAIL 21%”| WC1129| WC1129| 2
8                                         EZ UPPER HANDLE| R7205| CON- HAN-U113| 1
9                                EZ SHEAR BENT CAMLOCK PIN| R7153| CON- CML-0100| 1
10                                         EZ-20 FLR BLADE| WX2583| RAW-BDE- 120B| 1
11                                              EZ-20 TAIL| R7301| CON- TAL-0220| 1
12                                   BEARING ASSY, 120 / 126| R7528| SUB- BNG-0120| 2
13                                HARDWARE KITS 120/126/220| WR1517| FAS- KIT-D113| 1
14                           BOLT, MlO x 80 HEX, 10.9, ZINC PLT| WR1510| FAS- BLT-EZ80| 2
15                                    PIN, TENSION, MlO x 30| WR1548| FAS-PIN- EZ02| 2
16                                  M6-1 x 16, SHCS, ZINC PLT| WR1581| FAS- SCW-5021| 2
17                                        M6 x 12 BHSCS ZP| WR1585| FAS- SCW-5612| 10
18                                BUTTON SPRING, HAIRPIN, ¾6| WR1630| GEN- SPR-0847| 1
19              SPRING, COMPRESSION, 0.989 x 4″, x 0.105, 14 COIL| WR1635| GEN-SPR-4075| 2
20                           GRIP, 1″ x 4″, SQ TEXTURED RUBBER| WK230| GEN- HAN-0100| 1
21                          FOOT CAP,¾” BLACK VINYL, FCR-12| WL793| GEN- CAP-5039| 2
22                              RIVETED SHEAR FENCE 19.75IN| R7178| CON- FNC-1000| 1
23                            ¼ x 1¼” FLAT HEAD AL RIVET 100| WR1553| FAS- RVT-2513| 2
24             EZ END CAP, BLACK, FITS SQ TUBE ID OF 0.584 – 0.68″| WL790| GEN-CAP-1075| 1
25                              SET SCREW, M6 x 8 CUP POINT| WR1739| FAS-SCW- EZ88| 2

REPLACEMENT PARTS

EZ50
14| REPLACEMENT lOMM X 80MM AXLE BOLT| 29898| 863-RP-EZ80
7| EXTRUSION-W-RAIL EZ RAIL, (AL-52865), 21.375″ LONG| WC1129| CON-RAL-W021
17                M6-l.O X 12MM ALLEN 10.9 ZINC BUTTON SOCKET CAP WR1585| __ FAS-SCW-5612

TROUBLESHOOTING

Before troubleshooting double-check the manual:

• Is your shear properly assembled?
• Is it being operated correctly?
• Is it properly lubricated?
• Has the blade been honed as recommended?

Visually inspect shear, watching for objects that might obstruct the blade or powerhead travel:

• Foreign material is present between the blade and anvil, in the pin springs, or under the cam.
• Check your blade for chips, cracks, or burrs.
• Make sure bearings are intact and lubricated. They should not be spinning/moving on the cam during use.
• NOTE: This troubleshooting is for all Bullet shears. If you are uncertain if it pertains to your shear, please contact Marshalltown customer service.

PROBLEM                                      CHECK FIRST CHECK SECOND                                    CHECK THIRD CHECK FOURTH

Difficulty cutting| Ensure the cam lock is OFF. If equipped, engage power lobes (Model 226)| Make sure the handle is FULLY extended| Check blade sharpness/ condition| Inspect and lubricate bearings/pins
Not cutting completely through the material| Inspect pins for oblong/wallowed orifice| Adjust front stroke stop (MAGNUM shears)| Check bearings for wear/play| Ensure the blade is proper nominal height
Blade sticking after completing cuts| Check/remove & replace blade stops if damaged| Ensure blade screws are tight| Remove the anvil, turn it over, reinstall| __ Check for marks on the anvil (overbite)
Rough or crushed cuts| Check veneer thickness (max= 1/15″)| Check blade condition (chips, burrs, breaks)| Ensure the blade is honed and sharp| Review the approved materials list
Cuts aren’t square| Loosen fence screws, align fence, tighten| Check pins for uneven wear| Inspect blade and anvil/blade-stop for contact|
Handle not returning to the open position| Ensure pins are lubricated| Apply grease to the contact area of the bearing| Lubricate axle bolts| Check springs for breakage
The material won’t fit into the cut area| Check the max thickness of the material for your shear| Reverse backstroke stop| Ensure the blade is proper nominal height| If you have two bearings, switch which bearing is engaged
Cam lock pin bent/stuck| Do not  lift or carry the shear by the handle| Return the handle slowly to the open position – do not “let it fly”| Disengage the cam lock pin BEFORE cutting|
Blade chipping| Hone as directed in manual c~2s cut s, then daily)| Do not cut stranded bamboo| Do not cut high-pressure laminate| Check veneer thickness (max=1/15″)
Pin openings wallowed out/ oblong where the cam axle passes through| Do not lift or carry the shear by the handle| Return the handle slowly to the open position – do not “let it fly”| Check veneer thickness (max= 1/15″)| Review the approved materials list
Not cutting to the edge of material| Check fence alignment – adjust if needed| Do not “angle” material beyond the blade edge| Ensure angle fence(s) are installed with WIDE edge inward (620 models)|

• 104 S. 8th Ave., Marshalltown, IA
• Phone800-888-0127 / 641-753-0127
• Fax800-477-6341 / 64 1-753-6341
• www.MARSHALLTOWN.com
• WS2689revC

Documents / Resources

| MARSHALLTOWN WL793 20 Inch EZ Flooring Shear [pdf] Instruction Manual
WS2689revC, R7323, R7212, R7123, R7083, R7234, R7199, WC1129, R7205, R7153, WX2583, R7301, R7528, WR1517, WR1510, WR1548, WR1581, WR1585, WR1630, WR1635, WK230, WL793, WL793 20 Inch EZ Flooring Shear, WL793, 20 Inch EZ Flooring Shear, EZ Flooring Shear, Flooring Shear
---|---

References

• MARSHALLTOWN® - Professional Quality Tools for All
• Honing Your Blade - MARSHALLTOWN®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>