AlgoForce E1500 Gold Detector User Guide
- August 8, 2024
- AlgoForce
Table of Contents
AlgoForce E1500 Gold Detector
Specifications
- Product Name: AlgoForceTM E1500
- Technology: Ultra-Fine Pulse Induction with VLF Sensitivity and PI Power
- Origin: Designed & Assembled in Australia by ALGOFORCE PTY LTD
FAQs
- Q: How do I adjust the audio volume on the AlgoForceTM E1500?
- A: Press the Vol/Vibration buttons to modify the Audio Volume. Hold the Vol/Vibration buttons to adjust Vibration.
- Q: Where is the AlgoForceTM E1500 designed and assembled?
- A: The AlgoForceTM E1500 is designed and assembled in Australia by ALGOFORCE PTY LTD.
Assembly
- Plug the USB cable into the control box.
- Secure the control box to the shaft using two M5 screws.
- Attach the armrest to the sliding rail.
- Secure the power bank with the straps.
- Connect the USB cable to the power bank.
- Set the shaft to the appropriate length and attach the coil.
- Plug the coil connector into the control box.
- Tie the coil cable and USB cable to the shaft using the cable straps.
Quick Start
Press the Vol/Vibration buttons to modify the Audio Volume. Hold the Vol/Vibration buttons to adjust Vibration. Press the Backlight Adjust button for backlight control. Use the Minus and buttons to modify Sensitivity.
To adjust other settings:
- Press Right/Auto GB in the Main Detection UI to access the menu.
- Navigate with Left/Pinpoint or Right/Auto GB.
- Modify the selected setting with Minus or Plus.
- Press Return/Auto FS to go back to the Main Detection UI.
PRODUCT INFORMATION
- Power On
- Connect the power bank to the control box and turn it on. To power the detector, hold the Power On/Off button for 3 seconds, then release it. Repeat to turn it off.
- Factory Reset (if necessary)
- Hold the Minus and buttons for 3 seconds in Miscellaneous.
- Calibrate Coil (if installing a new coil)
- In Coil Selection, select the coil icon to save calibration data. Modify the Coil Size if needed (hold Return/Auto FS to enter edit mode). Raise the coil 1 meter away from metal and soil.
- If the LCDs “Hold ⊖ + ⊕ to calibrate,” hold the Minus and buttons until calibration starts. Calibration takes 25 seconds. Keep the coil in the air throughout. The LCD shows “Coil Ready” when done.
- Perform Auto Frequency Scan (Auto FS) (if necessary select the quietest frequency to eliminate electromagnetic interference)
- Activate Auto FS by holding the Return/Auto FS button in the Main Detection UI.
- The Auto FS process takes 50 seconds.
- Set Sensitivity, Audio Settings, and Vibration (to preferred levels)
- Adjust Sensitivity, aligning the Real-time Scrolling Detection Signal peak with the
- Detection Threshold in the absence of a target.
- Perform Auto Ground Balance (Auto GB) (to eliminate ground response)
- Hold the Right/Auto GB button. Raise and lower the coil until the ground response is minimized or two short beeps are heard, then release the button.
- Begin Detecting
- Keep the coil close to the ground and swing left and right at a pace of about 1 m/s.
- Pinpoint detected target (if needed)
- Enter the Pinpoint UI by pressing the Left/Pinpoint button in the Main Detection UI. Return to the Main Detection UI by pressing the Return/Auto FS button.
PRODUCT FUNCTIONS
- Sensitivity
- Audio Threshold
- Audio Tone
- Audio Treble
- Soil Type
- Detection Mode
- Frequency Scan
- Coil Selection
- Real-time Scrolling Signal
- Ground Drift Indicator (G.D.I)
- Dual Ground Balance Values
- Backlight Level
- High Tone Signal Strength
- Soil Mineralisation
- Low Tone Signal Strength
- Vibration Level
- Audio Volume Level
- Selected Coil Size
- Auto GB In Progress Indicator
- Detection Threshold
Button Functions
- Power On/Off
- Backlight Adjust
- Minus
- Plus
- Vol/Vibration ↓
- Vol/Vibration ↑
- Left/Pinpoint
- Return/Auto FS
- Right/Auto GB
Scan the QR code for the user manual
Caution: AlgoForce E1500 is not intended for use in residential environments and may not provide adequate protection to radio reception in such environments.
Uncover Gold with Ultra-Fine Pulse Induction Technology: VLF Sensitivity, PI Power, Affordable Excellence! Designed & Assembled in Australia by ALGOFORCE PTY LTD.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>