DALS DCP-LNR24-WH 20W 1 LED Linear Strip Light Installation Guide
- August 7, 2024
- dals
Table of Contents
Installation Guide for
DCP-LNR24-WH
DCP-LNR24-WH 20W 1 LED Linear Strip Light
MODEL| WATTS| DELIVERED LUMENS| KELVIN| VOLTAGE|
**DIMMABLE***
---|---|---|---|---|---
DCP-LNR24-WH| 20W| 1785 Im| 1268+CCT 2700-6500K| 120V| Dais Connect App
Application Dais Connect
ITEMS INCLUDED IN THE BOX
- LED recesed light
- Junction box
- Mounting hardware
Installation guide for gypsum board
BEFORE YOU START
BEFORE STARTING INSTALLATION, SHUT THE LINE FEED POWER OFF USING THE CIRCUIT
BREAKER.
Instructions pertaining to a risk of fire, electric shock or injury to
persons. Installation must be done according to local electrical codes.
Installation should be done by a certified electrician.
This class B digital apparatus complies with Canadian ICES-005. This digital
apparatus does not exceed the Class B limits for radio-noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
-
Cut hole in ceiling and prepare supply wires. Install and unshield the line feed wire 6” (15 cm) and strip wires 5/8” (1.6 cm). Bring supply power to junction box through knockout.
-
Open the lid of the junction box. Use the quick connectors to pair the wires from the mains with the wires from the connection box.
-
Compress the springs and push the fixture into the opening.
It is easier to do one spring at a time. -
INSTALLATION OF 2 OR MORE FIXTURES TOGETHER:
Unscrew the end caps where both fixtures meet. Slide the mounting bracket into the middle rail of each fixture. Make sure it is properly centered on the joint before tightening the 4 set screws.
Installation guide for suspended ceiling
-
Unscrew the butterfly nut at the back of the fixture to remove the spring clips
-
A) CENTERED/OFFSET INSTALLATION: Create a 2” opening in the panel.
B) PERIMETER INSTALLATION: Remove 2” from the side of the panel.
C) INSTALLATION ON RAILS: Plan adding 2 rails spaced 2-1/4” apart. Cut the panel consequently.
*BOTH LNR24 AND LNR48 FIXTURES CANNOT BE INSTALLED ON A SINGLE PANEL. -
Insert the linear fixture inside the suspended ceiling and let it rest onto the rails. Finally, put the suspended ceiling panel back.
A) CENTERED/OFFSET INSTALLATION:
B) PERIMETER INSTALLATION:
C) INSTALLATION ON RAILS:
TIPS:
It is also possible to only add one rail and use the existing frame as shown
in the example beside.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Innovation, Science, and Economic Development Canad licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with FCC/ISEDC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>