Total Restroom 3040 LED Lighted Mirror Instruction Manual
- August 6, 2024
- Total Restroom
Table of Contents
Total Restroom 3040 LED Lighted Mirror
Specifications:
- Product: LED Lighted Mirror
- Components: Screw, Expansion Tube, Installation Manual,Z-Bar
- Usage: Indoor use only
- Hotline: +1 302 336 8180
Product Usage Instructions
Installation Safety:
Inspect the product upon receipt for transit damage or missing parts. Handle
with care and protect against knocks. Ensure no hidden pipes or cables in the
wall before drilling. Wear eye protection when drilling.
Caution:
Do not disassemble the product. The light diodes can cause eye damage.
Aftercare Instructions:
Clean using a dry cloth only when turned off. Avoid cleaning agents or
abrasive materials. Prevent moisture contact with the lamp.
Usage Steps:
- Briefly touch the button to turn the mirror on or off.
- Press and hold the button to change the color temperature when the mirror is on.
- Optionally wire to wall switch for ON/OFF memory function.
- Adjust brightness by pressing and holding the button.
- Release the button at desired brightness level to set it.
- To defog, press defogger button; it will auto-stop after 60 mins of continuous operation.
- To turn off anti-fog function, press the button again.
- To turn blue backlight on/off, press and hold the button.
FAQ:
Q: What should I do if any part of the product is damaged?
A: If any part is damaged, do not use the product. Contact our hotline at
+1 302 336 8180 for assistance.
Q: Can I use cleaning agents to clean the mirror?
A: No, only use a dry cloth for cleaning when the mirror is turned off.
Avoid cleaning agents and abrasive materials.
SAFETY INSTRUCTIONS
WARNING AND SAFETY INSTRUCTIONS
Before assembling your LED Lighted Mirror fixture, please make sure that you carefully read through this instruction sheet, refer back to them during installation to ensure your product is fitted safely and correctly. Keep these instructions for future use.
WARNING Risk of Fire and Electric Shock
- All fittngs must be installed in accordance with current IEE wiring regulations. If in doubt, consult a qualified electrician.
- Switch off the electrical supply at the main circuit board BEFORE installation and maintenance.
- Suitable for indoor use only. This product should be positioned well away from curtains and fabrics. Never cover the mirror.
- Regularly check the cord, the transformer and all other parts for damage. If any part is damaged the product should not be used.
INSTALLATION SAFETY
- Inspect the product immediately upon receipt for the transit damage or missing parts. Handle the product with care and protect against knocks to all sides and edges of the glass.
- Ensure there are no hidden pipes or cables in the wall before drilling.
- Wear suitable eye protection when drilling. Take care if drilling on tiled surfaces in case the drill slips.
CAUTION
The light source of this product is non-changeable light diodes (LED). Do
not disassemble the product, as the light diodes can cause damage to the eyes.
NOTE: The important safeguards and instructions that appear in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care, are factors that can’t be built into any product. These factors must be supplied by the person(s) caring for and operating the fixture. Do not install this fixture in hazardous locations.
CHECK PRODUCT LIST AFTER OPENING THE PACKAGE
- LED Lighted Mirror –1pce
- Screw –5pcs
- Expansion Tube –5pcs
- Installation Manual –1pce
- Z-Bar –1pce
TOOLS YOU MAY NEED
INSTALLATION MANUAL
-
Measure the center of the holes and mark the drilling locations.
-
Ensure markings are leveled.
-
Using a drill, make holes and fill with supplied wall plugs.
-
Align the mounting bracket with the wall plug hole and screw the bracket to the wall.
-
We provide plug with mirrors.
-
Optional to cut the plug directly and connect to electrical wiring if using wall switch.
-
ATTENTION: Please cut off the main power supply before wiring!
-
Place the mirror against the wall and slide down as shown in image.
OPERATION INSTRUCTION
ON/OFF Function
- Briefly touch the button to turn the mirror on or off.
- Press and hold the button to change the color temperature when the mirror is on.
- Optional to be wired to wall switch by ON/OFF memory function.
Dimmer Function
- Briefly touch the button to turn the mirror on or off.
- Press and hold the button to adjust the brightness.
- Release the button when the brightness reaches your desired level to set it.
Anti-Fog Function
- The mirror begins to warm up and defog after you press the defogger button.
- Press the button again to turn off the anti-fog function.
- Press and hold the button to turn the blue backlight on or off.
- Note: To prevent damage from prolonged high temperatures, the defogger will automatically stop after 60 minutes of continuous operation.
AFTERCARE INSTRUCTIONS
Clean using a soft dry cloth only when turned off. Never use cleaning agents
or abrasive materials. Do not allow moisture to come into contact with lamp.
THANK YOU FOR YOUR SUPPORT.
We wish you have wonderful experience in our product. If you have any other needs or queries, please feel free to contact us by hotline: +1 302 336 8180, and get replies within 48 business hours.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>