Juniper EDGE Height Adjustable Desk Installation Guide
- August 5, 2024
- JUNIPer
Table of Contents
Juniper EDGE Height Adjustable Desk
Specifications
- Product Name: ESHA EDGE Height-Adjustable Desk
- Parts Included: Adjustable Leg, Surface Attachment Bracket, Surface Support Bracket, Width Adjusting Bracket, Control Box, Cable, 24 C-Leg Foot, Main Surface, Support Bar, Left-Leg Cover, Right-Leg Cover, Floor Modesty Panel, T-Bracket, Wood Screw
- Dimensions: Adjustable to 68″ length
Product Usage Instructions
- Connect Legs and Support Brackets to Adjustable Surface Bracket
- Slide one support bracket underneath each end of the adjustable surface bracket. Set one leg at each end ensuring all pre-drilled holes are aligned. Secure with machine screws.
- Set Frame on Surface and Set Length Align the frame with the surface width and measure from the outer edges of workstation legs to determine the proper workstation length. The frame length should measure to 68″.
- Tighten Screws on Adjustable Surface Bracket
- Tighten the screws on the adjustable surface brackets to secure the length.
- Secure Frame & Handset to Surface
- Attach the frame to the surface using wood screws and tighten the screws on the adjustable center bracket.
- Remove Glide and Inner Bracket
- Twist off both glides and remove the screws holding the inner brackets. This step is necessary for adding feet to the workstation.
- Secure Feet to Legs Using 4 screws for each foot, secure them to the legs with the longer side of the foot facing the front of the workstation.
- Connect Leg Cables and Handset Cable to Control Box
- If not adding a height-adjustable return surface, connect the cables and handset to the control box. Otherwise, refer to specific instructions for installing a return surface control box. Secure Support Bar Secure the support bar to the center of the main surface using wood screws and tighten them. Flip the surface over after securing.
EDGE
Height-Adjustable Desk
Includes Add-Ons: A1 | A2
General Installation Guide
Stand-Alone Desk
Overview
EDGE Height-Adjustable Desk
Quantities are for a single Stand-Alone Desk. Parts may vary depending on
project, but install steps will remain the same.
STAND-ALONE DESK
Parts List 
*Disregard Stand-Alone Desk control box and cable if installing a return surface. Return surface comes with its own control box and cables.
Connect Legs and Support Brackets to Adjustable Surface Bracket
Slide one support bracket underneath each end of adjustable surface bracket.
Set one leg at each end. Be sure all pre-drilled holes are aligned and secure
with machine screws.
Note: Longer side of support brackets will be facing front of workstation and
welded brackets from legs will be facing back of workstation. 
Set Frame on Surface and Set Length
Align frame with surface width and measure from outer edges of workstation
legs to determine proper workstation length. Frame length will measure to 68”.
Inset will be 2” for each side
Note: Run handset cable through cutout at bottom of frame. For left hand
return, run wire on right side. For right hand return, run wire on left side.
.
Tighten Screws on Adjustable Surface Bracket
Tighten adjustable surface brackets screws to secure length.
Secure Frame & Handset to Surface
Using wood screws, attach frame to surface and tighten screws on adjustable
center bracket.
Remove Glide and Inner Bracket
Twist off both glides. Then, using an Allen wrench remove screws that are
holding the inner brackets.
Note: Glide and inner brackets must be removed so feet can be added to
workstation. 
Secure Feet to Legs
Using 4 screws for each foot, secure to legs with longer side of foot facing
the front of workstation.
Connect Leg Cables and Handset Cable to Control Box
Note: If adding a height-adjustable return surface, DO NOT connect cables or
handset to control box. A return surface control box will be installed on PAGE
25, replacing existing control box. 
Secure Support Bar
Secure support bar to center of the main surface. Insert wood screws through
support bar and into underside of surface. Tighten the screw on main profile
beam. Flip surface over.
Remove Panel from Leg Covers
Slide out panels from both leg covers and set aside. 
Slide Leg Covers Around Frame Legs
Leg covers should align with sides of surface, and front/back edge of surface.
Prep Location for Leg Cover Brackets
With front panels in position, place short side of bracket against inner wall
of leg cover, and long tab against inside of removable cover. With a marker,
mark location of holes on inner wall of leg cover.
Secure Brackets to Leg Covers
Remove front panel and screw bracket to inner wall of leg cover where location
was marked. Then, attach front removable panel and screw bracket to front
removable panel. 
Position Leg Cover Tops in Place
Set leg cover tops on small brackets inside leg covers.
Attach T-Brackets to Floor Modesty Panel
Secure 4 T-brackets using provided wood screws. 
Attach Floor Modesty Panel to Leg Covers
Secure modesty panel with T-brackets using provided wood screws. The floor
modesty panel will be inset 3/4″ from the leg covers. 
Power up and Initialize
Note: If installing a height-adjustable return surface, skip step. Power up
and
initialize will occur on PAGE 25.
Connect cord to power source then press and hold and simultaneously for 5
seconds until both leg columns are in lowest position. Desk will slightly
rise, lower again, and then stop. Release buttons. The system is now
operational. 
END OF STAND-ALONE SECTION
Optional | Monitor Arm
Follow proper instructions when installing monitor arm.
Note: Bottom of monitor arm mount should not make contact with the EDGE
Height-Adjustment components. Laminate Modesty Panel
Overview
EDGE Height-Adjustable Desk
Quantities are for a single EDGE Laminate Modesty Panel . Parts may vary
depending on project, but install steps will remain the same.
MODESTY PANEL
Parts List 
Secure Brackets to Modesty Panel
Connect the L-bracket to the modesty panel using screws. Secure tightly.
Attach Modesty Panel to Surface
Attach modesty panel to surface using wood screws provided with brackets.
Panel will be center aligned and inset 2.5″ from back of surface to edge of
bracket. 
Return Surface
Overview
EDGE Height-Adjustable Desk
Quantities are for a single EDGE Return Surface. Parts may vary depending on
project, but
install steps will remain the same. 
RETURN SURFACE
Parts List 
Connect Return Leg to Support Bracket
Secure return leg support bracket to return leg from using 6 screws.
Remove Glide and Inner Bracket
Twist off leg glide. Then, using an Allen wrench remove screws that are
holding the inner bracket and remove bracket from leg.
Note: Glide and inner bracket must be removed so foot can be added to
workstation.
Measure and Adjust Beam Width
Secure T-foot to return leg using 4 screws. Secure Main Surface
Requires 4 wood screws.
Note: The return leg will be centered along the depth of the return surface.
Attach Flat Brackets to Main Surface
Attach 2 flat brackets under the main surface using 4 wood screws. See
measurements below. 
Attach Return Surface to Main Surface
Position return surface on top of attached brackets and secure with 4 wood
screws.
Note: The return leg will be centered along the depth of the return surface.
Attach support bar
Center and secure support bar between flat brackets for extra support and
rigidity. 
Remove Back Panel From Return-Leg Cover
Slide out back panel from return-leg cover and set aside.
Slide Return-Leg Cover Around Return Leg
Return-leg cover should align with sides of return surface, and front/back
edge of return surface.
Prep location for Leg Cover Brackets
With front panels in position, place short side of bracket against inner wall
of leg cover, and long tab against inside of removable cover. With a marker,
mark location of holes on inner wall of leg cover. 
Secure Brackets to Leg Covers
Attach the front removable panel and secure T-bracket to panel. 
Position Leg Cover Tops in Place
Set leg cover tops on small brackets inside leg covers. 
Install Return Control Box
Remove existing control box from main surface and replace with return control
box. Secure with existing screws. Connect all three leg cables, handset, and
power cable.
Power Up and Initialize
Connect cord to power source then press and hold and simultaneously for 5
seconds until both leg columns are in lowest position. Desk will slightly
rise, lower again, and then stop. Release buttons. The system is now
operational. 
1-866-999-0955 |
hello@juniperoffice.com |
juniperoffice.com
© 2024 Juniper Office | Version 24.0.0
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>